820195 Force CARBURETOR (BOTTOM) (TC-120A)


820195 CARBURETOR (BOTTOM) (TC-120A) Force H1201A90A, H120412RD, H120412SD CARBURETOR
820195 CARBURETOR (BOTTOM) (TC-120A) Force
Rating:
103

Buy CARBURETOR (BOTTOM) (TC-120A) 820195 Force genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$775.93
 

09-03-2018
400 Hundredths Pounds
Arai: Arai
Arai Helmets 820195 Corsair-X Giugliano Helmet (Giugliano, XX-Large)
Perhaps the most fabled name in the entire Arai lineup, the Corsair has long been renowned as one of the most advanced, highest quality helmets available anywhere in the world.||It represents the culmination of Arai's vast experience in helmet design and unwavering focus on rider protection.||And with features like the ingenious VAS shield mechanism, dramatically improved air flow and ventilation and an antimicrobial Eco-Pure liner, the Corsair-X has certainly earned its place as Arai's flagship model.The Corsair-X has Arai's Intermediate Oval||By combining the pin trajectory, which is based on an imaginary axis, with the two trajectories of the double pivot point slot, the shield opens and closes smoothly even with the much lower shield mount position.A dual-function lever releases both the sid||Being able to see the shield mechanism allows for easier shield changes.Improved Glance Off Ability:The VAS pivot cover is now smaller and lower than the previous design, yielding an average of 24 mm more area above the cover.
Number on catalog scheme: 1
 

Compatible models:

Force entire parts catalog list:

H1201A90A 1990,1991,1992,1993,1994
H120412RD 1995
H120412SD 1996,1997

Information:

2. Start the LEXT3037 PC Program, or Flash from Electronic Technician (ET).3. Select the engine Personality Module part number to be programmed into the ECM, and proceed with programming the Personality Module. The new ECM is shipped with a blank Personality Module.4. PC Program Personality Module Messages and Their Meaning are discussed below. A new ECM comes with a blank (previously unprogrammed) personality module. A blank personality module will prompt you for all three of the following messages. The information contained in the "ECM Status" will be scrambled and meaningless if the module has not been previously programmed (this is normal).- Message - "The engine ID in the flash file does not match the engine ID in the ECM."- Meaning - The ECM has a personality module in it for a different engine, for example, the ECM has a 3406E personality module in it, and you are attempting to program a 3176B personality module into it.- What you should do - Stop the transfer and access information about "ECM Status" under the "Electronic Control Module" menu. Make sure the file you are about to transfer is for the same engine it will be installed in.- Message - "The application ID in the flash file does not match the application ID in the ECM."- Meaning - The ECM has a personality module in it for a different application, for example, the ECM has a 3176B On-Highway Truck personality module in it, and you are attempting to program a 3176B Challenger personality module into it.- What you should do - Stop the transfer and access information about "ECM Status" under the "Electronic Control Module" menu. Make sure the file you are about to transfer is for the On-Highway Truck application.- Message - "The ECM ID in the flash file does not match the ECM ID in the ECM."- Meaning - The ECM is not for use in the 3176B, C-10, C-12, and 3406E On-Highway truck application.- What you should do - Stop the transfer and access information about "ECM Status" under the "Electronic Control Module" menu. Make sure the ECM on the engine is for a 3176B, C-10, C-12, and 3406E On-Highway truck application. If you access the "ECM Status" under the "Electronic Control Module" menu of the PC Program, but do not follow this information access by programming the Personality Module, you must turn the vehicle ignition key switch to the OFF position, and then to the ON position before using an ECAP or ET. If you do not cycle the key switch after reading the "ECM Status", the ECM will not communicate with your service tool, or start the engine. Cycling the key switch is not necessary following successful programming of a personality module using the Flash Designer Program.5. Start the engine and check for proper operation. - Program any parameters not previously in the old personality module if 253-02 Check Customer Or System Parameters (56) code is active. Read the code from the Active Diagnostic code screen of the ECAP or ET to determine the parameter(s) requiring programming.- Remember, on initial power up of a new ECM, five parameters (six for a 3406E) must be programmed to avoid a 253-02 Check Customer Or System Parameters (56) code. They are Full Load Setting (FLS), Full Torque Setting (FTS), Vehicle Speed Calibration (ppm), Rating Number and Engine Serial Number (and Injector Codes, 3406E only). If the ECM serial number does not end in "CG" or "CJ" and the ECM is flash programmed with a NOV95 Personality Module the Total Tattletale may change by a random value when a Customer Specified Parameter value is programmed. To correct this problem upgrade to AUG96 or later Personality Module.6. Clear / reset trip data. - Flash programming may cause the trip data to appear scrambled when viewed. After flash programming is complete reset the trip data before releasing the vehicle.


Parts carburetor Force:

F440906
 
F440906 CARBURETOR GASKET
H040312RD, H040312SD, H040312UD, H0407E92C, H0507A90C, H0507A90D, H0507A91A, H0507A91C, H0507A92A, H0507E91B, H0706A91B, H075312SD, H075312UD, H0906R83D, H1000H79A, H1004H79A, H1006B81C, H1007H79A, H1008H83C, H1058H82G, H1058V83H, H1059H76D, H1059H77
F589061-3
F664061-2
 
F664061-2 CARBURETOR COMPLETE (BOTTOM)
H1201A90A, H1251A89D, H1251A89E
820203
CARBURETOR (TOP) (TC-119A)
820203 CARBURETOR (TOP) (TC-119A)
H1201A90A, H120412RD, H120412SD
Back to top