F40906-1 Force FLANGE GASKET


F40906-1 FLANGE GASKET Force H0202B80L, H0202B81M, H0202H79K, H0202H82N, H0252B83G, H0252H77B, H0252H78C, H0252H78D, H0254H75A, H0306B80C, H0307H81D, H0350H78L, H0351H76K, H0352H77H, H0352H79L, H0353H78K, H0353H80M, H0353H81N, H0353H82P, H0356H75F, H0357C86A, H0357C87A, H0357C88 FLANGE
F40906-1 FLANGE GASKET Force
Rating:
103

Buy FLANGE GASKET F40906-1 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: -
 

Force entire parts catalog list:

H0202B80L 1980
H0202B81M 1981
H0202H79K 1979
H0202H82N 1982
H0252B83G 1983,1984
H0252H77B 1977
H0252H78C 1978
H0252H78D 1978
H0254H75A 1975,1976
H0306B80C 1980
H0307H81D 1981
H0350H78L 1978
H0351H76K 1976
H0352H77H 1977,1978
H0352H79L 1979
H0353H78K 1978
H0353H80M 1980
H0353H81N 1981
H0353H82P 1982
H0356H75F 1975,1976,1977
H0357C86A 1986
H0357C87A 1987
H0357C88B 1988
H0357F88A 1988
H0357H83N 1983,1984
H0456B78J 1978
H0456B79K 1979
H0456B80L 1980,1981
H0457H82N 1982
H0457H83P 1983,1984
H0503B83A 1983
H0503H84B 1984
H0504H88C 1988
H0504H88D 1988
H0507B85A 1985
H0507C86A 1986
H0507C87A 1987
H0507C87C 1987
H0507C88B 1988
H0507F87B 1987
H0507F88A 1988
H0507H81A 1981
H0507H82B 1982
H0555H74G 1974,1976
H0558H79L 1979
H0559B80M 1980
H0559H77H 1977
H0559H77J 1977
H0559H78K 1978
H0559H80N 1980,1981
H0559H83R 1983
H0606H84A 1984,1985,1989
H0659B78B 1978

Information:


Do not operate or work on this engine unless you have read and understand the instructions and warnings in the Operation and Maintenance Manual. Failure to follow the instructions or heed the warnings could result in injury or death. Contact any Caterpillar dealer for replacement manuals. Proper care is your responsibility.
Accidental engine starting can cause injury or death to personnel working on the equipment.To avoid accidental engine starting, disconnect the battery cable from the negative (−) battery terminal. Completely tape all metal surfaces of the disconnected battery cable end in order to prevent contact with other metal surfaces which could activate the engine electrical system.Place a Do Not Operate tag at the Start/Stop switch location to inform personnel that the equipment is being worked on.
Table 1
Parameter Value
Face Runout (Axial Eccentricity) of the Flywheel 0.15 mm (0.006 inch)
Bore Runout (Radial Eccentricity) of the Flywheel 0.15 mm (0.006 inch)
Bore Runout (Radial Eccentricity) Flywheel clutch pilot bearing bore 0.13 mm (0.005 inch) Introduction
Use this procedure to check the axial and radial runout of the flywheel.Required Tools
Table 2
Required Tools
Item Qty Part Number Part Name
T1 1 8T-5096 Tool Gp
T1a 1 7H-1645 Holding Rod
T1b 1 7H-1940 Universal Attachment
T1c 1 7H-1942 Dial Indicator
T1d 1 7H-1945 Holding Rod
T1e 1 7H-1948 Swivel Clamp Face Runout (Axial Eccentricity) of the Flywheel - Check
Illustration 1 g06442773
Checking face runout of the flywheel
(T1a) 7H-1645 Holding Rod
(T1b) 7H-1940 Universal Attachment
(T1c) 7H-1942 Dial Indicator
(T1d) 7H-1945 Holding Rod
(T1e) 7H-1948 Swivel Clamp
Install Tooling (T1c) onto the flywheel housing with Tooling (T1a), (T1d), and (T1e). Always put a force on the crankshaft in the same direction before the dial indicator is read. This will remove any crankshaft end clearance.
Set the dial indicator to read 0.0 mm (0.00 inch).
Turn the flywheel at intervals of 90 degrees and read the dial indicator.
Take the measurements at all four points. Find the difference between the lower measurements and the higher measurements. This value is the runout. The maximum permissible face runout (axial eccentricity) of the flywheel must not exceed 0.15 mm (0.006 inch).Bore Runout (Radial Eccentricity) of the Flywheel - Check
Illustration 2 g06442491
Checking bore runout of the flywheel
(T1a) 7H-1645 Holding Rod
(T1b) 7H-1940 Universal Attachment
(T1c) 7H-1942 Dial Indicator
(T1d) 7H-1945 Holding Rod
(T1e) 7H-1948 Swivel Clamp
Install Tooling (T1c) onto the flywheel housing with Tooling (T1a), (T1d), and (T1e). Make an adjustment of Tooling (T1b) so that the dial indicator makes contact on the flywheel.
Set the dial indicator to read 0.0 mm (0.00 inch).
Turn the flywheel at intervals of 90 degrees and read the dial indicator.
Take the measurements at all four points. Find the difference between the lower measurements and the higher measurements. This value is the runout. The maximum permissible bore runout (radial eccentricity) of the flywheel must not exceed 0.15 mm (0.006 inch).Bore Runout (Radial Eccentricity) of the Flywheel Clutch Pilot Bearing Bore - Check
Illustration 3 g06442800
Flywheel clutch pilot bearing bore
(T1a) 7H-1645 Holding Rod
(T1b) 7H-1940 Universal Attachment
(T1c) 7H-1942 Dial Indicator
(T1d) 7H-1945 Holding Rod
(T1e) 7H-1948 Swivel Clamp
Install Tooling (T1c) onto the flywheel housing with Tooling (T1a), (T1d), and (T1e). Make an adjustment of Tooling (T1b) so that the dial indicator makes contact on the flywheel.
Set the dial indicator to read 0.0 mm (0.00 inch).
Turn the flywheel at intervals of 90 degrees and read the dial indicator.
Take the measurements at all four points. Find the difference between the lower measurements and the higher measurements. This value is the runout. The maximum permissible pilot bore runout of the flywheel must not exceed 0.13 mm (0.005 inch).


Back to top