F474509 Force CHOKE LINK


F474509 CHOKE LINK Force H0558H79L, H0559B80M, H0559H77H, H0559H77J, H0559H78K, H0559H80N, H0559H83R, H0606H84A, H0659B78B CHOKE
F474509 CHOKE LINK Force
Rating:
28

Buy CHOKE LINK F474509 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 10
 

Force entire parts catalog list:

H0558H79L 1979
H0559B80M 1980
H0559H77H 1977
H0559H77J 1977
H0559H78K 1978
H0559H80N 1980,1981
H0559H83R 1983
H0606H84A 1984,1985,1989
H0659B78B 1978

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-6192 Pliers 1
B 7M-3978(1) Piston Ring Expander Gp 1
7B-7974(2) Piston Ring Expander Gp 1
C 5P-8639 Hydraulic Press (Connecting Rod Bearing) 1
8F-0024 Hose Assembly 1
1P-2375 Connecting Coupler 1
1P-2376 Connecting Coupler 1
5P-8651 Spacer 1
5P-8649 Adapter 1
5P-8650 Bushing Adapter 1
9U-6600 Hand Hydraulic Pump 1
(1) For use with 137 mm (5.4 inch) bores.
(2) For use with 145 mm (5.7 inch) bores.Note: Prior to removal from the engine, the pistons and connecting rod assemblies were marked. The components must be reassembled together. The components must be installed in the original location in the engine. Do not interchange any of the components.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01017742
Illustration 2 g01018268
The connecting rod must be heated for the installation of the piston pin bearing. Do not use a torch.
Raise heat of connecting rod (6) along Length (Y). (Y) Maximum Length for heating the connecting rod ... 95 mm (3.7 inch)
Allow the connecting rod and the bearing to cool to room temperature.
Use Tooling (C) to remove the old bearing and install new bearing (7) at the same time. The adapter of Tooling (C) should make full contact with the surfaces of connecting rod (6). Note: Orient the bearing joint within 5 degrees of either Location (X).
Use a pin boring machine to machine the bore of bearing (7) to the correct diameter. Diameter of bearing bore ... 60.035 0.008 mm (2.3636 0.0003 inch)
Illustration 3 g01056145
Position the spring for the oil control piston ring in the oil ring groove in the piston body assembly.
Position oil control piston ring (3) over the spring. Position the oil control piston ring so that the gap is 180 degrees from the joint in the spring. Install the oil control piston ring on the piston with Tooling (B).
Use Tooling (B) to install intermediate piston ring (2) with the side that has the identification “UP-2” toward the top of the piston.
Use Tooling (B) to install top piston ring (1) with the side that has the identification “UP-1” toward the top of the piston.
Position piston rings (1), (2), and (3) so the gaps are 120 degrees from each other.
Check the clearance between the ends of piston rings (1), (2), and (3). Refer to Specifications, "Pistons And Rings".
Position piston body assembly (4) on connecting rod (6). Apply clean engine oil to connecting rod pin (8) and install the connecting rod pin. Install pin retainer (5) with Tooling (A).
Install upper connecting rod bearing (9) in connecting rod (6). Note: Ensure that the bearing locking tab is located in the notch of the connecting rod.
Install lower connecting rod bearing (10) in connecting rod bearing cap (11). Note: Ensure that the bearing locking tab is located in the notch of the connecting rod bearing cap.
Ensure that the dowels are installed in the connecting rod bearing cap. End By:
Install the pistons and connecting rods. Refer to Disassembly and Assembly, "Pistons and Connecting Rods - Install".


Parts choke Force:

F391926-1
 
F391926-1 CHOKE SOLENOID PLUNGER
H0202B81M, H0202H79K, H0252B83G, H0252H77B, H0252H78D, H0254H75A, H0257F88A, H0257F88B, H0306B80C, H0307H81D, H0350H78L, H0351H76K, H0352F90B, H0352F90C, H0353E91A, H0353E91B, H0355D89A, H0356F89B, H0356H75F, H0357C86A, H0357C87A, H0357C88B, H0357F88
F85924
 
F85924 CHOKE SOLENOID
H0202B81M, H0202H79K, H0252B83G, H0252H77B, H0252H78D, H0254H75A, H0306B80C, H0307H81D, H0350H78L, H0351H76K, H0357C86A, H0357H83N, H0558H79L, H0559B80M, H0559H77H, H0559H77J, H0559H78K, H0559H80N, H0559H83R, H0606H84A, H0659B78B, H0700H79A, H0709B79
FO16850
 
FO16850 CHOKE SHAFT AND LEVER
H0558H79L, H0559B80M, H0559H77H, H0559H77J, H0559H78K, H0559H80N, H0559H83R, H0659B78B, H0700H79A, H0709B79A, H0750H79A, H0756H80F, H0756H81G, H0756H82H, H0757B79E, H0757H75A, H0757H76C, H0757H78D, H0758H80B, H0759H79A, H0850H79A, H0850H80A, H0850H81
F85033
 
F85033 CHOKE ROD SWIVEL
H0559H77H, H0559H77J, H0559H78K, H0700H79A, H0709B79A, H0750H79A, H0756H80F, H0756H81G, H0756H82H, H0757B79E, H0757H75A, H0757H76C, H0757H78D, H0758H80B, H0758H82E, H0759H79A, H0850H79A, H0850H80A, H0850H81C, H0851H79A, H0851X88A, H0853F88B, H0853F89
F85925
 
F85925 CHOKE ROD
H0558H79L, H0559B80M, H0559H77H, H0559H77J, H0559H78K, H0559H80N, H0559H83R, H0606H84A, H0659B78B, H0700H79A, H0709B79A, H0750H79A, H0756H80F, H0756H81G, H0756H82H, H0757B79E, H0757H75A, H0757H76C, H0757H78D, H0758H80B, H0758H82E, H0759H79A, H0850H79
FO13947
 
FO13947 CHOKE SHAFT RETURN SPRING
H0558H79L, H0559B80M, H0559H77H, H0559H77J, H0559H78K, H0559H80N, H0559H83R, H0659B78B, H0757H75A, H0757H76C, H0850H79A, H0850H80A, H0851H79A, H0855H79A, H0856B80H, H0857B78F, H0857H79G, H0858B80C, H0859B79B, H0859H77A, H0859H78A, H1000H79A, H1004H79
FO13555
 
FO13555 CHOKE SHUTTER
H0558H79L, H0559B80M, H0559H77H, H0559H77J, H0559H78K, H0559H80N, H0559H83R, H0659B78B, H0757H75A, H0757H76C, H0850H79A, H0850H80A, H0850H81C, H0851H79A, H0855H79A, H0856B80H, H0856H82K, H0857B78F, H0857H79G, H0858B80C, H0858B82E, H0858C84H, H0859B79
F10143
 
F10143 CHOKE SHAFT RETURN SPRING
H0252B83G, H0257F88A, H0257F88B, H0355D89A, H0356F89B, H0357C86A, H0357C87A, H0357C88B, H0357F88A, H0606H84A, H0758H82E, H0851X88A, H0853F88B, H0853F89C, H0853F89E, H0853F89F, H0853F89G, H0856A89A, H0856C87A, H0856C87B, H0856F84A, H0856F85A, H0856F86
Back to top