FO12250 Force CHOKE SHUTTER


FO12250 CHOKE SHUTTER Force H0202B80L, H0202B81M, H0202H79K, H0202H82N, H0252B83G, H0252H77B, H0252H78C, H0252H78D, H0254H75A, H0306B80C, H0307H81D, H0350H78L, H0351H76K, H0352H77H, H0352H79L, H0353H78K, H0353H80M, H0353H81N, H0353H82P, H0357H83N CHOKE
FO12250 CHOKE SHUTTER Force
Rating:
8

Buy CHOKE SHUTTER FO12250 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 7
 

Force entire parts catalog list:

H0202B80L 1980
H0202B81M 1981
H0202H79K 1979
H0202H82N 1982
H0252B83G 1983,1984
H0252H77B 1977
H0252H78C 1978
H0252H78D 1978
H0254H75A 1975,1976
H0306B80C 1980
H0307H81D 1981
H0350H78L 1978
H0351H76K 1976
H0352H77H 1977,1978
H0352H79L 1979
H0353H78K 1978
H0353H80M 1980
H0353H81N 1981
H0353H82P 1982
H0357H83N 1983,1984

Information:


Illustration 1 g00856926
SchematicTest Step 1. Check for Connector Damage
Turn the keyswitch to the OFF/RESET position.
Check the connectors and wiring for the following problems: damage, corrosion, abrasion and incorrect attachment.Expected Result:The connectors and wiring should be free of the following problems: damage, corrosion, abrasion and incorrect attachment.Results:
OK - Proceed to Test Step 2.
Not OK - Repair: Repair the connectors or wiring and/or replace the connectors or wiring.Verify that the repair eliminates the problem.STOPTest Step 2. Check the Switch Status on ET
Connect ET to the service tool connector.
Turn the keyswitch to the ON position.
Operate the ground level shutdown switch. Observe the status for the ground level shutdown switch on ET.Expected Result:The status of the switch should be "ON" with the switch in the SHUTDOWN position. The status should be "OFF" when the switch is in the RUN position.Results:
OK - The switch is operating normally.Repair: If an intermittent problem is suspected, refer to Troubleshooting, "Electrical Connectors - Inspect".STOP
Not OK - Proceed to Test Step 3.Test Step 3. Short the Wires at the Switch
Disconnect the J700/P700 ground level shutdown switch.
Use a suitable piece of wire to short P700:B (Digital Return) and P700:C (Ground Level Shutdown (NC)).
Turn the keyswitch to the OFF/RESET position.
Turn the keyswitch to the ON position.
Observe the status of the ground level shutdown switch on ET.Note: The status should be "ON".
Remove the jumper wire from the connector.
Install the jumper wire between P700:B (Digital Return) and P700:A (Ground Level Shutdown (NO)).
Turn the keyswitch to the OFF/RESET position.
Turn the keyswitch to the ON position.
Observe the status of the ground level shutdown switch on ET.Note: The status should be "OFF".
Remove the jumper wire.Expected Result:The status should be "OFF" when P700:B (Digital Return) is shorted to P700:C (Ground Level Shutdown (NC)). The status should be "ON" when P700:A (Ground Level Shutdown (NO)) is shorted to P700:B (Digital Return).Results:
OK - The problem is not with the harness and/or the ECM.Repair: Temporarily connect a new switch. Verify that the new switch solves the problem before you permanently install the new switch.STOP
Not OK - There is a problem in the harness and/or the ECM. Proceed to Test Step 4.Test Step 4. Check for a Short Circuit in the Wiring Harness
Turn the keyswitch to the OFF/RESET position.
Disconnect the J1/P1 ECM connector and the J700/P700 ground level shutdown switch connector.
Measure the resistance between P1:40 (Ground Level Shutdown (NO)) and P1:5 (Digital Return).
Measure the resistance between P1:23 (Ground Level Shutdown (NC)) and P1:5 (Digital Return).
Measure the resistance between P1:40 (Ground Level Shutdown (NO)) and P1:23 (Ground Level Shutdown (NC)).
Measure the resistance between P1:23 (Ground Level Shutdown (NC)) and engine ground.
Measure the resistance between P1:40 (Ground Level Shutdown (NO)) and engine ground. Expected Result:The resistance should be greater than 20,000 Ohms for each measurement.Results:
OK - The wiring harness is not shorted. Proceed to Test Step 5.
Not OK - There is a short in the harness between the switch and the ECM.Repair: Repair the circuit.Verify that the repair eliminates the problem.STOPTest Step 5. Check the Resistance through the Harness
Install a jumper wire between P700:A (Ground Level Shutdown (NO)) and P700:B (Digital Return).
Measure the resistance between P1:40 (Ground Level Shutdown (NO)) and P1:5 (Digital Return).
Remove the jumper wire.
Install the jumper wire between P700:C (Ground Level Shutdown (NC)) and P700:B (Digital Return).
Measure the resistance between P1:23 (Ground Level Shutdown (NC)) and P1:5 (Digital Return).
Remove the jumper wire.Expected Result:The resistance should be less than 10 Ohms for each measurement.Results:
OK - The resistance is within acceptable limits. Proceed to Test Step 6.
Not OK - There is an open or excessive resistance in the harness.Repair: Repair the circuit.Verify that the repair eliminates the problem.STOPTest Step 6. Short the Switch Inputs at the ECM
Remove the F715-PU wire from P1:40. Remove the F716-WH wire from P1:23. Remove the 998-BR wire from P1:5. Use a 121-9587 Wire Removal Tool .
Insert a jumper wire with Deutsch sockets on each end between P1:23 and P1:5.
Reconnect all connectors.
Turn the keyswitch to the ON position.Additional diagnostic codes may be generated because the digital return will no longer be connected to the other sensors and/or switches. Clear the codes after you complete this test.
Observe the status of the ground level shutdown switch on ET.Note: The status should be "OFF".
Turn the keyswitch to the OFF/RESET position.
Disconnect the J1/P1 ECM connector.
Remove the jumper wire.
Insert the jumper wire between P1:40 and P1:5.
Reconnect all of the connectors.
Turn the keyswitch to the ON position.
Observe the status of the ground level shutdown switch on ET.Note: The status should be "ON".
Turn the keyswitch to the OFF/RESET position.
Remove the jumper wire.Expected Result:The status should be "OFF" when the wire is inserted between P1:23 and P1:5. The status should be "ON" when the wire is inserted between P1:40 and P1:5.Results:
OK - The harness is faulty.Repair: Repair the circuit.Verify that the repair eliminates the problem.STOP
Not OK - The switch and the wiring appear to be working properly, but the ECM is not reading the switch inputs properly.Repair: Verify your results before you replace the ECM. Refer to Troubleshooting, "Replacing the ECM".STOP


Parts choke Force:

FO16383
 
FO16383 CHOKE SHAFT AND LEVER
H0352H77H, H0352H79L, H0353H78K, H0353H80M, H0353H81N, H0353H82P, H0356H75F, H0456B78J, H0456B79K, H0456B80L, H0457H82N, H0507H81A, H0507H82B, H0555H74G
F391926-1
 
F391926-1 CHOKE SOLENOID PLUNGER
H0202B81M, H0202H79K, H0252B83G, H0252H77B, H0252H78D, H0254H75A, H0257F88A, H0257F88B, H0306B80C, H0307H81D, H0350H78L, H0351H76K, H0352F90B, H0352F90C, H0353E91A, H0353E91B, H0355D89A, H0356F89B, H0356H75F, H0357C86A, H0357C87A, H0357C88B, H0357F88
FO16385
 
FO16385 CHOKE SHAFT RETURN SPRING
H0352H77H, H0352H79L, H0353H78K, H0353H80M, H0353H81N, H0353H82P, H0356H75F, H0456B78J, H0456B79K, H0456B80L, H0457H82N, H0507H81A, H0507H82B, H0555H74G
FO15725
 
FO15725 CHOKE RELIEF VALVE
H0257F88A, H0257F88B, H0352F90B, H0352F90C, H0352H77H, H0353E91A, H0353E91B, H0355D89A, H0356F89B, H0356H75F, H0357C87A, H0357C88B, H0357F88A, H0357F89C, H0357G90A, H0407E92C, H0456B78J, H0456B79K, H0456B80L, H0457H82N, H0504P89B, H0507A89C, H0507A89
FO10280
 
FO10280 CHOKE SHUTTER RETAINING SCREW AND LOCKWASHER
H0033H75C, H005201RS, H005201SD, H005201TS, H005201UD, H0052C88A, H0060B76A, H0062H79M, H0064H78D, H0082H76G, H0082H79K, H0091B80B, H0091H79A, H0091H84D, H009201RS, H009201SD, H0092284D, H0092B80G, H0092H79F, H0092H81H, H0092H84L, H0092S88A, H0092S91
FO15724
 
FO15724 CHOKE SHUTTER
H0257F88A, H0257F88B, H0352F90B, H0352F90C, H0352H77H, H0353E91A, H0353E91B, H0355D89A, H0356F89B, H0356H75F, H0357C87A, H0357C88B, H0357F88A, H0357F89C, H0357G90A, H0407E92C, H0456B78J, H0456B79K, H0456B80L, H0457H82N, H0504P89B, H0507A89C, H0507A89
F10129
 
F10129 CHOKE RELIEF VALVE
H0252B83G, H0357C86A, H0457H83P, H0503H84B, H0504H88C, H0504H88D, H0505C89B, H0507B85A, H0507C86A, H0507C87A, H0507C87C, H0507C88B, H0507F87B, H0507F88A, H0507Z89B
F10130
 
F10130 CHOKE RELIEF VALVE SPRING
H0252B83G, H0257F88A, H0257F88B, H0355D89A, H0356F89B, H0357C86A, H0357C87A, H0357C88B, H0357F88A, H0457H83P, H0503H84B, H0504H88C, H0504H88D, H0504P89B, H0505C89B, H0507A89C, H0507B85A, H0507C86A, H0507C87A, H0507C87C, H0507C88B, H0507F87B, H0507F88
Back to top