F437719 Force CLUTCH SPRING


F437719 CLUTCH SPRING Force H0252H77B, H0252H78C, H0252H78D, H0254H75A CLUTCH
F437719 CLUTCH SPRING Force
Rating:
63

Buy CLUTCH SPRING F437719 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 21
 

Compatible models:

Force entire parts catalog list:

H0252H77B 1977
H0252H78C 1978
H0252H78D 1978
H0254H75A 1975,1976

Information:


Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     -     Strap Wrench     1    Start By:
Remove engine.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g02786236
Use Tooling (A) in order to remove engine oil filter (5) . Remove plug (3) and drain the engine lubricating oil. Remove O-ring seal (4) (not shown) from plug (3) . Refer to Operation and Maintenance Manual, "Engine Oil and Filter - Change" for correct procedure.
Remove breather hose (1) from the clip. Position the breather hose away from the engine oil pan.
Loosen nut (6) and remove tube assembly (2) . Remove O-ring seal (7) and seal (8) from the tube assembly.
Illustration 2 g02786240
Remove nuts (9) and bolts (10) from engine oil pan (11) .Note: The bolts are different lengths. Note the position of the different bolts.
Attach a suitable lifting device to engine oil pan (11) . Support the weight of the engine oil pan. The engine oil pan weighs approximately 41 kg (90 lb).
Use the lifting device to remove engine oil pan (11) from the cylinder block.
Remove gasket (12) from the cylinder block.Installation Procedure
Table 2
Required Tools    
Tool    Part Number    Part Description    Qty    
A     -     Loctite 5900     -    
B     -     Loctite 243     -    
C     -     Straight Edge     1    Note: In order to install a cast iron oil pan, the engine must be removed from the machine.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the face of the cylinder block is clean and free from damage. Inspect the studs in the cylinder block for damage. If necessary, replace the studs.
Ensure that the engine oil pan is clean and free from damage.
Illustration 3 g02786279
Illustration 4 g02786281
Apply a bead of Tooling (A) to Positions (Y) on the cylinder block.Note: If the bridge piece for the cylinder block has just been installed, the engine oil pan must be installed before Tooling (A) has cured.
Illustration 5 g02786286
Illustration 6 g02786316
Align a new gasket (12) with the studs in the cylinder block. Install the gasket to the cylinder block.
Attach a suitable lifting device to engine oil pan (11) . The engine oil pan weighs approximately 41 kg (90 lb).
Use the lifting device to align engine oil pan (11) with the studs in the cylinder block. Install the engine oil pan to the cylinder block. Remove the lifting device from the engine oil pan.
Install nuts (9) and bolts (10) finger tight.
Align the rear face of engine oil pan (11) to the rear face of cylinder block (13) on both sides. Use Tooling (C) and a feeler gauge in order to check the alignment between the engine oil pan and the cylinder block. The maximum step that is allowed between the cylinder block and the sump is 0.1 mm (0.004 inch).
Tighten bolts (9) and nuts (10) to a torque of 22 N m (16 lb ft). Refer to Specifications, "Engine Oil Pan" for t


Parts clutch Force:

F437521
 
F437521 CLUTCH
H0252H77B, H0252H78C, H0252H78D, H0254H75A
F901728
 
F901728 CLUTCH SHIFT PIN
H0062B78J, H0062H79K, H0062H79M, H0064H78D, H0064H82H, H0067H79C, H0071H84E, H0072B81D, H0072H79B, H0072H80C, H0072H82E, H0082H76G, H0082H78J, H0082H79K, H0252H77B, H0252H78C, H0252H78D, H0254H75A
F901721
 
F901721 CLUTCH SHIFT CAM
H0252H77B, H0252H78C, H0252H78D, H0254H75A
Back to top