F480518 Force CYLINDER HEAD


F480518 CYLINDER HEAD Force H0700H79A, H0750H79A, H0756H80F, H0756H81G, H0756H82H, H0757B79E, H0757H76C, H0757H78D, H0758H80B, H0758H82E, H0759H79A, H0850H79A, H0850H80A, H0850H81C, H0851H79A, H0855H79A, H0856B80H, H0856F84A, H0856F85A, H0856F86A, H0856H82K, H0857B78F, H0857H79 CYLINDER
F480518 CYLINDER HEAD Force
Rating:
8

Buy CYLINDER HEAD F480518 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 72
 

Force entire parts catalog list:

H0700H79A 1979
H0750H79A 1979
H0756H80F 1980
H0756H81G 1981
H0756H82H 1982
H0757B79E 1979
H0757H76C 1976
H0757H78D 1978
H0758H80B 1980
H0758H82E 1982,1983,1984
H0759H79A 1979
H0850H79A 1979
H0850H80A 1980
H0850H81C 1981
H0851H79A 1979
H0855H79A 1979
H0856B80H 1980
H0856F84A 1984
H0856F85A 1985
H0856F86A 1986
H0856H82K 1982,1983
H0857B78F 1978
H0857H79G 1979
H0858B80C 1980
H0858B82E 1982
H0858C84H 1984
H0859B79B 1979
H0859H77A 1977
H0859H78A 1978

Information:


Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g03409484
If suction pipe (5) has a support bracket, remove bolt (7) from bracket (8). Remove bolt (6) for the retaining clip.
Remove bracket (8). Note: Note the position and orientation of the components for the support bracket.
Remove bolts (4) from suction pipe (1).
Remove suction pipe (5) from oil pump (2).
Remove gasket (3) (not shown).
Remove bolts (1) and remove the assembly of engine oil pump (2) from the cylinder block.
Illustration 2 g03409496
If necessary, follow Step 7.a through step 7.c to disassemble engine oil pump assembly (2).
Remove bolts (11).
Remove front cover assembly (12) from engine oil pump assembly (2).
Make temporary mark on outer rotor (13) for assembly purposes. Remove the outer rotor from of engine oil pump (2).
Do not remove dowel (9) or dowel (10) from the housing of the engine oil pump unless the dowels are damaged.
Illustration 3 g03409497
If necessary, follow Step 9.a through step 9.c to remove cross over tube assembly (14).
Remove bolts (15) and bolts (16) from cross over tube assembly (14).
Remove cross over tube assembly (14) from the cylinder block.
Remove gasket (17) and gasket (18). Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 7H-1942 Dial Indicator 1
- Magnetic Base and Stand 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
If any part of the engine oil pump is worn or damaged, the complete assembly of the engine oil pump must be replaced.
Ensure that all components of the engine oil pump are clean and free from wear and damage. Refer to System Operation, Testing and Adjusting, "Engine Oil Pump - Inspect" for more information. Replace the complete assembly of the engine oil pump if any of the components are worn or damaged.
Illustration 4 g03409497
If necessary, follow Step 2.a through step 2.d to install cross over tube assembly (14).
Install new gasket (17) and new gasket (18).
Position cross over tube assembly (14) onto the cylinder block.
Install bolts (15) and bolts (16) to cross over tube assembly (14) finger tight.
Tighten bolts (15) and bolts (16) to a torque of 22 N m (195 lb in).
Illustration 5 g03409496
If necessary, follow Step 3.a through step 3.d to assemble engine oil pump assembly (2).
Lubricate the internal components for the assembly of the engine oil pump with clean engine oil.
Install outer rotor (13) to oil pump assembly (2). Ensure that the outer rotor is installed in the outer rotor original position and orientation.
Install front cover assembly (12) to engine oil pump assembly (2).
Install bolts (11) finger tight. Tighten the bolts to a torque of 22 N m (195 lb in).
Ensure that dowel (9) and dowel (10) are correctly located in the housing of engine oil pump (2).
Install bolts (7). Tighten the bolts to a torque of 22 N m (195 lb in).
Install the assembly of engine oil pump (2) to the cylinder block. Ensure that dowel (9) and dowel (10) are correctly aligned with the holes in the cylinder block.
Install bolts (1) to assembly of engine oil pump (2). Tighten the bolts to a torque of 22 N m (195 lb in).
Use Tooling (A) to check the backlash between idler gear and the crankshaft gear. Refer to Specifications, "Gear Group (Front)" for more information.
If suction pipe (5) had a support bracket, Follow Step 9.a through Step 9.e in order to install support bracket and the suction pipe.
Install a new gasket (3) (not shown) to suction pipe (5).
Install bolts (4) to suction pipe (1).
Position the assembly of suction pipe (5) onto oil pump (2). Tighten bolts (4) to a torque to 22 N m (195 lb in).
Position bracket (8) onto cylinder block and retaining clip. Install bolt (7) to the bracket. Install bolt (6) to the retaining clip. Hand tighten the bolts. Note: Ensure the correct location and orientation of the bra


Parts cylinder Force:

F93920
 
F93920 CYLINDER DRAIN REED STOP
H0352H77H, H0352H79L, H0353H78K, H0353H80M, H0353H81N, H0353H82P, H0356H75F, H0407E92C, H0456B78J, H0456B79K, H0456B80L, H0457H82N, H0457H83P, H0503H84B, H0504H88C, H0504H88D, H0504P89B, H0505C89B, H0507A89C, H0507A89D, H0507A90A, H0507A90B, H0507A90
F2A404757
 
F2A404757 CYLINDER DRAIN REED PLATE
H0700H79A, H0706A91B, H0709B79A, H0750H79A, H0756H80F, H0756H81G, H0756H82H, H0757B79E, H0757H75A, H0757H76C, H0757H78D, H0758H80B, H0758H82E, H0759H79A, H0850H79A, H0850H80A, H0850H81C, H0851H79A, H0851X88A, H0853F88B, H0853F89C, H0853F89E, H0853F89
817787A 1
 
817787A 1 CYLINDER DRAIN COVER
H0700H79A, H0706A91B, H0709B79A, H0750H79A, H0756H80F, H0756H81G, H0756H82H, H0757B79E, H0757H75A, H0757H76C, H0757H78D, H0758H80B, H0758H82E, H0759H79A, H0850H79A, H0850H80A, H0850H81C, H0851H79A, H0851X88A, H0853F88B, H0853F89C, H0853F89E, H0853F89
F85279-2
 
F85279-2 CYLINDER EXHAUST GASKET, UPPER
H0700H79A, H0709B79A, H0750H79A, H0756H80F, H0756H81G, H0756H82H, H0757B79E, H0757H75A, H0757H76C, H0757H78D, H0758H80B, H0758H82E, H0759H79A, H0850H79A, H0850H80A, H0850H81C, H0851H79A, H0851X88A, H0853F88B, H0853F89C, H0853F89E, H0853F89F, H0853F89
F369529
 
F369529 CYLINDER HEAD GASKET
H0709B79A, H0756H80F, H0757B79E, H0757H75A, H0757H76C, H0757H78D, H0758H80B, H0759H79A, H0857B78F, H0857H79G, H0859B79B, H0859H77A, H0859H78A
F499995
 
F499995 CYLINDER HEAD COVER
H0700H79A, H0709B79A, H0750H79A, H0756H80F, H0756H81G, H0756H82H, H0757B79E, H0757H76C, H0757H78D, H0758H80B, H0758H82E, H0759H79A, H0850H79A, H0850H80A, H0850H81C, H0851H79A, H0851X88A, H0853F88B, H0855H79A, H0856A89A, H0856B80H, H0856C87A, H0856C87
A438010 3
F630518
 
F630518 CYLINDER HEAD "B" & "C" MODELS
H0851X88A, H0853F88B, H0853F89C, H0853F89E, H0856A89A, H0856C87A, H0856C87B, H0856F86A, H0856Y89B
Back to top