818021 1 Force DECAL (BAYLINER & SPECTRUM MODELS)

3. Loosen the clamps on breather tube (1), and pull it back for clearance. Loosen the clamps on hose (3). Slide hose (3) off of the water pump cover.4. Remove two bolts and remove elbow (2). 5. Remove bolt (4) from the cover on the side of the cylinder block. 6. Remove the three bolts that hold cover (5) to the water pump. Remove cover (5) from the water pump. 7. Remove the two bolts, and remove elbow (7) from bonnet (6). Remove the two bolts, and remove bonnet (6) from the water pump. It is not necessary to remove bolts (10). These bolts only hold the cover to the timing gear cover.8. Remove six long bolts (9) that hold the water pump to the timing gear cover. Remove water pump (8). The following steps are for the installation of the water pump.9. Check the O-ring seals and gaskets, and make replacements if needed. 10. Make sure O-ring seal (11) is in position on the water pump. Put water pump (8) into position in the timing gear cover. Install the bolts that hold the water pump in place.11. Make sure the gaskets are in place. Connect bonnet (6) to the water pump. Connect elbow (7) to the bonnet. 12. Make sure O-ring seal (12) is in position, and install cover (5) on the water pump.13. Install bolt (4) on the cover on the side of the engine.14. Put breather tube (1) in position, and install the clamps that hold it.15. Install the alternator mounting group and alternator on the engine if so equipped. 16. Install the gasket and O-ring seal on elbow (2). Lubricate the O-ring seal with clean oil. Install elbow (2) in the bore of the water pump. Use two bolts to fasten the elbow to the cylinder head.17. Slide hose (3) into position on the water pump. Tighten the hose clamp.18. Fill the cooling system to the correct level. See the Operation & Maintenance Manual.Disassemble & Assemble Water Pump
Start By:a. remove water pump FLUID SPILLAGE CONTAINMENTCare must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the machine. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to "Tools And Shop Product Guide", NENG2500, for tools and supplies suitable to collect and contain fluids in Caterpillar machines. Dispose fluids according to local regulations and mandates. The water pump seal can be replaced without removing the water pump from the engine.An intermittent leakage of a small amount of coolant from the hole in the water pump housing is not an indication of a water pump seal failure. This is required to provide lubrication for the seal. Replace the water pump seal only if a large amount of leakage or a constant flow of coolant is observed draining from the water pump housing. 1. Remove O-ring seal (3) from adapter (4). Remove the adapter from housing (7). Remove the O-ring seal from the outside of the adapter.2. Remove bolt (1) and washer (2). Use Tooling (A) to remove impeller (6) from shaft (13).3. Remove spring and seal (5) from the shaft.4. Remove four bolts (16) from retainer (12) that hold the shaft assembly to the pump housing. Remove O-ring seal (18) from housing (7).5. Remove gear and shaft assembly (17) from the housing. Remove bolt (15), retainer (14), and retainer (12) from the shaft assembly.6. Use a press to remove shaft (13) from the gear. Remove bearing (9), spacer (10), and bearing (11) from the shaft.7. Remove lip seal (8) from the housing.8. Turn the housing over, and remove ceramic ring (20) and seal (19) from the housing. The following steps are for the assembly of the water pump.9. Use 4C-9500 Quick Cure Primerand clean shaft (13) and the seal counter bore in the pump housing.10. Install bearing (9), spacer (10), and bearing (11) on shaft (13).11. Put retainer (12) and gear (17) on the shaft assembly. Install retainer (14) and bolt (15) on the shaft.12. Use Tooling (B) to install lip seal (8) in housing (7). Install seal with the lip toward the inside of the housing. Put a small amount of clean engine oil on the lip of the seal.13. Install a new O-ring seal (18) on the housing.14. Put gear and shaft assembly (17) in position in the housing. Install bolts (16) that hold retainer (12) to the housing.
Do not damage or put hands on the wear surface of the carbon ring or the ceramic ring. Install the ceramic ring with the smoothest face of the ring toward the carbon seal assembly.
15. Put ceramic ring (20) in position in seal (19). Use hand pressure and Tool (C) to install the ceramic ring in the housing.
Avoid contaminating the seal faces with grease or oil. Also, avoid stretching the rubber seal during installation.
The carbon seal assembly must rotate with the water pump shaft after installation.16. Separate spring from seal (5). Use hand pressure and Tool (C) to install the seal on the shaft of gear and shaft assembly (17). Push the seal on the shaft until the seal faces make light contact. Install the spring on the shaft.17. Put impeller (6) in position on the shaft. Install washer (2) and bolt (1) that hold the impeller. Tighten the bolt to a torque of 39 3 N.m (29 2 lb ft).18. Install the O-ring seal on the outside diameter of adapter (4). Put a small amount of clean SAE 30 oil on the O-ring seal.19. Install O-ring seal (3) on the adapter.20. Put adapter (4) in position on the housing.End By:a. install water pump