825149A 1 Force DECAL KIT-SHIFT TO NEUTRAL


825149A 1 DECAL KIT-SHIFT TO NEUTRAL Force H009201UD, H009201US, H015201US, H015211SS, H025201TD, H025201TS, H025201US, H040312UD, H075312UD, H075412VD, H090412UD, H090422VD, H120412UD DECAL
825149A 1 DECAL KIT-SHIFT TO NEUTRAL Force
Rating:
33

Buy DECAL KIT-SHIFT TO NEUTRAL 825149A 1 Force genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$15.92
 

08-10-2019
0.0[0.00] Pounds
-: -
Mercury Marine New OEM Warning Decal, F609853, 825149A1, 37-825149A1, FA609853
Supersedes Part #F609853 || Supersedes to Part #825149A1/37-825149A1 || Please verify your own fitment
Number on catalog scheme: 23
 

Force entire parts catalog list:

H009201UD 1998
H009201US 1998
H015201US 1998
H015211SS 1996,1997
H025201TD 1997
H025201TS 1997
H025201US 1998
H040312UD 1998,1999
H075312UD 1998
H075412VD 1999
H090412UD 1998
H090422VD 1999
H120412UD 1998,1999

Information:


Illustration 1 g02901037
Table 1
Specification for 316-0062 Connecting Rods, 316-0063 Connecting Rods, 434-0480 Connecting Rods, and 434-0481 Connecting Rods
Item Qty Part Specification Description
A 1 229-9809 Bushing After installation, bore in bushing for new piston pin is 75.040 0.008 mm (2.9543 0.0003 inch).
Bore in the connecting rod for the bushing is 82.985 0.015 mm (3.2671 0.0006 inch).
B - - Distance between center of bearings is 420 mm (16.5354 inch).
C - - After the bolts are tightened, the bore in the connecting rod for the bearing is 157.000 0.013 mm (6.1811 0.0005 inch).
- - - Connecting end play is 0.72 to 1.28 mm (0.0284 to 0.0504 inch).
- - - The 316-0062 Connecting Rods and 434-0480 Connecting Rods are assembled in the even number cylinder bank of the engine. The chamfer side is facing the fillet radius of the crankshaft. When the marking on the side of the rod indicates "Even Front", the arrow points to the front of the engine.
- - - The 316-0063 Connecting Rods and 434-0481 Connecting Rods are assembled into the odd number cylinder bank. The chamfer side is facing the fillet radius of the crankshaft. When the marking on the side of the rod indicates "Odd Front", the arrow points to the front of the engine.
- - - Careful handling of the connecting rod is required at all times. The fracture face of the connecting rod and the fracture face of the connecting rod cap must not contact any surface. The connecting rod and the connecting rod cap must be laid flat on the sides. When possible, the rod assembly should be kept together in order to protect the fracture face when the connecting rod is out of the engine.
- - - The connecting rod and the connecting rod cap must be marked only with a mechanical etcher with the number of the cylinder. The cylinder number must be etched on the same surface as the part number and the serial number for the connecting rod.
Illustration 2 g03321190
The arrow represents the front of the engine block
(A) Bearing tab side
(3) Odd numbered connecting rod
(4) Even numbered connecting rod
Table 2
Assembly Specification for Type 1 Connecting Rods with 290-2541 Bolts
Item Qty Part Specification Description
1 6 290-2541 Bolts Use the following procedure to tighten the bolts of the connecting rod:
Note : Apply Bel-Ray Molylube 67700 to the threads and middle rings of bolt (2) and the contact surface under the bolt head.
1. Install the spacers (2) and the bolts (1). Hand tighten the bolts.
Note : Bolt 1 is identified as the middle bolt on the tab side of the bearing on the connecting rod. Tighten this bolt first in order to seat the bearing into the bore.
2. Tighten bolt 1 and bolt 2 to 105 5 N m (77 4 lb ft).
3. Tighten bolt 3 and bolt 4 to 105 5 N m (77 4 lb ft).
4. Tighten bolt 5 and bolt 6 to 105 5 N m (77 4 lb ft).
5. Again tighten bolt 1 and bolt 2 to 105 5 N m (77 4 lb ft)..
6. Again tighten bolt 3 and bolt 4 to 105 5 N m (77 4 lb ft).
7. Again tighten bolt 5 and bolt 6 to 105 5 N m (77 4 lb ft).
8. Turn bolt 3 and bolt 4 to 90 5 degrees.
9. Turn bolt 5 and bolt 6 to 90 5 degrees.
10. Turn bolt 1 and bolt 2 to 90 5 degrees.
2 2 269-0588 Spacers
Table 3
Assembly Specification for Type 1 Connecting Rods with 428-7386 Bolt As
Item Qty Part Specification Description
1 6 428-7386 Bolt As Use the following procedure in order to tighten the bolts of the connecting rod:
Lubricate each bolt with Bel-Ray Molylube 67700 by fully coating the elastomer rings, threads, and the contact surface under the bolt head.
1. Install all of the bolts into the spacers by pushing and rotating the bolt simultaneously.
Note: Rotating the bolt while pushing will avoid damage to the bolts.
2. Install the bolts into the connecting rod cap by pushing and rotating the bolt simultaneously.
3. Engage the threads by pushing and slowly rotating the bolt. Do not tap the bolt. All six bolts should have the threads engaged before the joint is drawn together on either side. The order of engaging the threads is bolts 1-2-3-4-5-6. Engaging bolt 1 and 2 first helps center the cap to the connecting rod. Once bolts 1 and 2 threads have engaged install the remaining bolts in order.
4. Tighten bolt 1 and bolt 2 to 105 5 N m (77 4 lb ft).
5. Tighten bolt 3 and bolt 4 to 105 5 N m (77 4 lb ft).
6. Tighten bolt 5 and bolt 6 to 105 5 N m (77 4 lb ft).
7. Again tighten bolt 1 and bolt 2 to 105 5 N m (77 4 lb ft).
8. Again tighten bolt 3 and bolt 4 to 105 5 N m (77 4 lb ft).
9. Again tighten bolt 5 and bolt 6 to 105 5 N m (77 4 lb ft).
10. Turn bolt 3 and bolt 4 an additional 90 5 degrees.
11. Turn bolt 5 and bolt 6 an additional 90 5 degrees.
12. Turn bolt 1 and bolt 2 an additional 90 5 degrees.
2 2 269-0588 Spacer


Parts decal Force:

FA609853
 
FA609853 DECAL, WARNING
H0071H84E, H0091H84D, H009201RS, H009201SD, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H015201RS, H015211SS, H0152B83J, H0152C84K, H0152S89A, H025201RD, H025201TD, H0357H83N, H040312RD, H040312SD, H0407E92C, H0457H83P, H0503H84B, H0504H88
F688585
 
F688585 DECAL-TILT LOCK
H0091H84D, H009201RS, H009201SD, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H015201RS, H015211SS, H0152C84K, H0152S89A, H025201RD, H025201TD
818029
 
818029 DECAL-FUEL MIX
H005201RS, H0052C88A, H0091H84D, H009201RS, H009201SD, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H015201RS, H015211SS, H0152C84K, H0152S89A, H025201RD, H025201TD, H0353E91A, H040312RD, H040312SD, H0407E92C, H0507A91C, H0706A91B, H075312S
855443A97
 
855443A97 DECAL SET
H009201SD, H009201UD, H009201US, H015201US, H015211SS
809856A96
 
809856A96 DECAL SET
H009201SD, H015211SS
826343 9
 
826343 9 DECAL (STARBOARD)
H025201TS, H025201US
826343 10
 
826343 10 DECAL (PORT)
H025201TS, H025201US
855394A98
Back to top