A517397 Force DECAL, PORT "CHRYSLER"

Table 1
J1939 Code and Description CDL Code and Description Comments
651-5
Engine Injector Cylinder #01 : Current Below Normal 1-5
Cylinder #1 Injector : Current Below Normal The code is logged.
The A6:E2 ECM detects an open circuit.
The ECM continues the attempt to energize the solenoid circuit until the circuit is repaired.
651-6
Engine Injector Cylinder #01 : Current Above Normal 1-6
Cylinder #1 Injector : Current Above Normal The code is logged.
The ECM detects a short circuit. The ECM will disable the solenoid circuit to prevent damage to the circuit.
The ECM disables this solenoid circuit. The ECM will periodically attempt to energize the solenoid circuit until the circuit is repaired.
652-5
Engine Injector Cylinder #02 : Current Below Normal 2-5
Cylinder #2 Injector : Current Below Normal The code is logged.
The ECM detects an open circuit.
The ECM continues the attempt to energize the solenoid circuit until the circuit is repaired.
652-6
Engine Injector Cylinder #02 : Current Above Normal 2-6
Cylinder #2 Injector : Current Above Normal The code is logged.
The ECM detects a short circuit. The ECM will disable the solenoid circuit to prevent damage to the circuit.
The ECM disables this solenoid circuit. The ECM will periodically attempt to energize the solenoid circuit until the circuit is repaired.
653-5
Engine Injector Cylinder #03 : Current Below Normal 3-5
Cylinder #3 Injector : Current Below Normal The code is logged.
The ECM detects an open circuit.
The ECM continues the attempt to energize the solenoid circuit until the circuit is repaired.
653-6
Engine Injector Cylinder #03 : Current Above Normal 3-6
Cylinder #3 Injector : Current Above Normal The code is logged.
The ECM detects a short circuit. The ECM will disable the solenoid circuit to prevent damage to the circuit.
The ECM disables this solenoid circuit. The ECM will periodically attempt to energize the solenoid circuit until the circuit is repaired.
654-5
Engine Injector Cylinder #04 : Current Below Normal 4-5
Cylinder #4 Injector : Current Below Normal The code is logged.
The ECM detects an open circuit.
The ECM continues the attempt to energize the solenoid circuit until the circuit is repaired.
654-6
Engine Injector Cylinder #04 : Current Above Normal 4-6
Cylinder #4 Injector : Current Above Normal The code is logged.
The ECM detects a short circuit. The ECM will disable the solenoid circuit to prevent damage to the circuit.
The ECM disables this solenoid circuit. The ECM will periodically attempt to energize the solenoid circuit until the circuit is repaired.
655-5
Engine Injector Cylinder #05 : Current Below Normal 5-5
Cylinder #5 Injector : Current Below Normal The code is logged.
The ECM detects an open circuit.
The ECM continues the attempt to energize the solenoid circuit until the circuit is repaired.
655-6
Engine Injector Cylinder #05 : Current Above Normal 5-6
Cylinder #5 Injector : Current Above Normal The code is logged.
The ECM detects a short circuit. The ECM will disable the solenoid circuit to prevent damage to the circuit.
The ECM disables this solenoid circuit. The ECM will periodically attempt to energize the solenoid circuit until the circuit is repaired.
656-5
Engine Injector Cylinder #06 : Current Below Normal 6-5
Cylinder #6 Injector : Current Below Normal The code is logged.
The ECM detects an open circuit.
The ECM continues the attempt to energize the solenoid circuit until the circuit is repaired.
656-6
Engine Injector Cylinder #06 : Current Above Normal 6-6
Cylinder #6 Injector : Current Above Normal The code is logged.
The ECM detects a short circuit. The ECM will disable the solenoid circuit to prevent damage to the circuit.
The ECM disables this solenoid circuit. The ECM will periodically attempt to energize the solenoid circuit until the circuit is repaired.
Electrical shock hazard. The injector for the common rail fuel system uses 90-120 volts.
Contact with high pressure fuel may cause fluid penetration and burn hazards. High pressure fuel spray may cause a fire hazard. Failure to follow these inspection, maintenance and service instructions may cause personal injury or death.
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High-Pressure Fuel Lines" for safety information.Refer to Systems Operation, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Table 2
Troubleshooting Test Steps Values Results
1. Check for Codes
A. Establish communication between Cat® Electronic Technician (ET) and the ECM. Refer to Troubleshooting, "Electronic Service Tools", if necessary.
B. Download the "Warranty Report" from the ECM before performing any troubleshooting or clearing diagnostic trouble codes.
C. Determine the diagnostic trouble code that relates to an injector.
Codes
Result: A logged -5 code or a logged -6 code is present.
Proceed to Test Step 2.
Result: An active -5 code is present.
Proceed to Test Step 3.
Result: An active -6 code is present.
Proceed to Test Step 4.
2. Inspect the Electrical Connectors and Wiring
A. Turn the keyswitch to off.
B. Thoroughly inspect the connectors at the cylinder head for the injectors. Refer to Troubleshooting, Electrical Connectors - Inspect for the procedure.
Electrical Connectors and Wiring
Result: There is a problem with a connector and/or wiring.
Repair: Repair or replace any connector or wiring as necessary. Use the service tool to clear all codes and verify that the problem is resolved.
Result: There is not a problem with any connectors and/or wiring.
Repair: The problem maybe intermittent. Refer to Troubleshooting, Electrical Connectors - Inspect. If the wiring appears to be ok, perform the following procedure:
1. Turn the keyswitch to OFF.
2. Disconnect the connectors. Inspect the terminals for proper installation. The terminals should be dry and clean.
3. Insert a pin into each socket. Verify that each socket grips the pin firmly. Repair any problems that are found.
4. Connect all the connectors.
5. Verify that the problem is resolved. Return the unit to service.
3. Check the External Engine Harness for an Open Circuit
A. Turn the keyswitch to OFF.
Note: A strong electrical shock hazard is present if the keyswitch is not turned to OFF.
B. Disconnect the harness connectors for the affected cylinder at the cylinder head.
C. Fabricate a jumper wire to shor