F310398 Force DECAL-TOTE TANK (USA - NOT SHOWN)


F310398 DECAL-TOTE TANK (USA - NOT SHOWN) Force H0091H84D, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H0152C84K, H0152S89A, H0257F88A, H0257F88B, H0355D89A, H0356F89B, H0357C86A, H0357C87A, H0357C88B, H0357F88A, H0504H88C, H0504H88D, H0505C89B, H0507A89C, H0507C86A, H0507C87A, H0507C87 DECAL
F310398 DECAL-TOTE TANK (USA - NOT SHOWN) Force
Rating:
38

Buy DECAL-TOTE TANK (USA - NOT SHOWN) F310398 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: -
 

Force entire parts catalog list:

H0091H84D 1984
H0092284D 1984,1985,1986,1987,1988,1989,1990,1991,1992,1993,1994,1995
H0092H84L 1984
H0092S88A 1988
H0092S91A 1991
H0093S91A 1991
H0152C84K 1984
H0152S89A 1989
H0257F88A 1988,1989
H0257F88B 1988,1989,1991
H0355D89A 1989
H0356F89B 1989
H0357C86A 1986
H0357C87A 1987
H0357C88B 1988
H0357F88A 1988
H0504H88C 1988
H0504H88D 1988
H0505C89B 1989
H0507A89C 1989
H0507C86A 1986
H0507C87A 1987
H0507C87C 1987
H0507C88B 1988
H0507F87B 1987
H0507F88A 1988
H0507Z89B 1989
H0851X88A 1988
H0853F88B 1988,1989
H0856C87A 1987
H0856C87B 1987
H0856F86A 1986

Information:


Table 1
Diagnostic Codes Table
CDL Code Code Description Comments
91-3 Throttle Position Sensor : Voltage Above Normal The Electronic Control Module (ECM) detects signal voltage that is not in the acceptable range.
The code is logged. The ECM flags the throttle position as invalid data and a default value is used. The engine speed is limited to high idle.
91-4 Throttle Position Sensor : Voltage Below Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged. The ECM flags the throttle position as invalid data and a default value is used. The engine speed is limited to high idle.
91-8 Throttle Position Sensor abnormal frequency, pulse width, or period The ECM detects an incorrect frequency on the throttle signal or an incorrect duty cycle on the throttle signal.
The code is logged. The ECM flags the throttle position as invalid data and a default value is used. The engine speed is limited to high idle. The throttle position sensor is mounted to a pedal assembly that allows the operator to control the speed of the engine. The geometry of the pedal assembly controls both the travel of the sensor and the range of the output signal. The throttle position sensor cannot be adjusted.The output from the throttle position sensor is a PWM signal that varies with the position of the throttle pedal. The throttle position sensor produces a minimum duty cycle in the released position and a maximum duty cycle in the fully depressed position. When the pedal is released, the ECM translates the sensor output signal to a throttle position of 0 percent. When the pedal is fully depressed, the ECM translates the output signal to a throttle position of 100 percent.
Illustration 1 g02075215
Schematic for throttle position sensor
Illustration 2 g01214474
P1 ECM connector
(P1-4) 8 VDC supply
(P1-5) Digital return
(P1-66) Throttle position
Table 2
Troubleshooting Test Steps Values Results
1. Check the Signal Frequency and the Duty Cycle at the Sensor
A. Turn the keyswitch to the OFF position.
B. Remove the wire from terminal location C (throttle position) on the harness side of the connector for the throttle position sensor.
C. Install a 326-4904 Adapter Cable As (3-PIN BREAKOUT) at the connector for the throttle position sensor.
D. Connect the connector for the throttle position sensor.
E. Turn the keyswitch to the ON position.
F. Measure the frequency and the duty cycle between terminal B (digital return) and terminal C (throttle position) at the 326-4904 Adapter Cable As (3-PIN BREAKOUT). Operate the throttle pedal while making the measurements.
G. Turn the keyswitch to the OFF position.
H. Remove the breakout harness. Restore the wiring for the harness connector to the original configuration.
Signal Frequency
Result: The frequency and the duty cycle are within specifications for the entire range of the pedal.
Repair: Repair or replace the harness.
STOP
Result:The ECM detects an incorrect frequency on the throttle signal or an incorrect duty cycle on the throttle signal. The frequency is below 150 Hz or the frequency is above 1000 Hz. The duty cycle is less than 5 percent or the duty cycle is greater than 95 percent.
Proceed to Test Step 2.
2. Check the Supply Voltage to the Sensor
A. Turn the keyswitch to the OFF position.
B. Disconnect the harness connector for the throttle position sensor.
C. Measure the voltage across terminal A (8 V supply) and terminal B (digital return) on the harness side of the connector.
Supply Voltage
Result: The supply voltage is above 7.5 VDC at the sensor connector.
Repair: The wiring is OK. Replace the sensor.
STOP
Result: The supply voltage is not above 7.5 VDC at the sensor connector. The supply voltage is not reaching the speed control.
Repair: Repair or replace the harness.
STOP
Test Step 1. The procedure corrected the issue. Return to service.Results:
The procedure did not correct the issue. - Repair: Contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).STOP


Parts decal Force:

F286585-1
 
F286585-1 DECAL, TILT RELEASE (NOT SHOWN)
H0060B76A, H0060B78B, H0060H79C, H0060H80D, H0062B78J, H0062H79K, H0062H79M, H0064H80F, H0064H82H, H0067H79C, H0070B79A, H0071H81B, H0071H82C, H0071H83D, H0071H84E, H0072B81D, H0072H79B, H0072H80C, H0072H82E, H0075H79A, H0082H76G, H0082H78J, H0082H79
FA540392
 
FA540392 DECAL, SAILOR PORT
H0091H83C, H0091H84D, H0095B81G, H0095H82H
F712894
 
F712894 DECAL-SPEED/SHIFT INDICATOR (RED)
H005201RS, H005201SD, H005201TS, H005201UD, H0052C88A, H0091H84D, H009201RS, H009201SD, H009201UD, H009201US, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H015201RS, H015201US, H015211SS, H0152C84K, H0152S89A, H025201RD, H025201TD, H025201T
F666396
 
F666396 DECAL-STBD
H0091H84D, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H0152C84K, H0152S89A
FX689397
 
FX689397 DECAL-PORT
H0091H84D, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H0152C84K, H0152S89A
F715528
 
F715528 DECAL-REAR
H0091H84D, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H0152C84K, H0152S89A
F662386
 
F662386 DECAL, "50"
H0507C87A, H0507C87C, H0507F87B, H0507F88A
Back to top