F667397 Force DECAL-PORT


F667397 DECAL-PORT Force H0091H84D, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H0152C84K, H0152S89A DECAL
F667397 DECAL-PORT Force
Rating:
83

Buy DECAL-PORT F667397 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 13
 

Force entire parts catalog list:

H0091H84D 1984
H0092284D 1984,1985,1986,1987,1988,1989,1990,1991,1992,1993,1994,1995
H0092H84L 1984
H0092S88A 1988
H0092S91A 1991
H0093S91A 1991
H0152C84K 1984
H0152S89A 1989

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A(1) 9U-6198 Crankshaft Turning Tool 1
A(2) 9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
B 8T-3052 Degree Wheel 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Discard all used Connecting Rod fasteners.
Inspect the pins of the crankshaft for damage. If the crankshaft is damaged, replace the crankshaft. Refer to Disassembly and Assembly, "Crankshaft - Remove" and Disassembly and Assembly, "Crankshaft - Install" for the correct procedure. Ensure that the bearing shells are clean and free from wear and damage. If necessary, replace the bearing shells.
Illustration 1 g02437999
Install upper bearing shell (5) into connecting rod (3). Ensure that the locating tab for the upper bearing shell is correctly seated in the slot in the connecting rod. Note: The ends of the upper bearing shell must be centered in the connecting rod. The ends of the upper bearing shell must be equally positioned in relation to the mating faces of the connecting rod.
Lubricate upper bearing shell (5) with clean engine oil.
Use Tooling (A) to rotate the crankshaft until the crankshaft pin is at the bottom dead center position.
Carefully pull connecting rod (3) against the crankshaft pin. Note: Do not allow the connecting rod to contact the piston cooling jet.
Clean connecting rod cap (2). Install lower bearing shell (4) into connecting rod cap (2). Ensure that the locating tab for the lower bearing shell is correctly seated in the slot in the connecting rod cap.
Lubricate the pin of the crankshaft and lubricate lower bearing shell (4) with clean engine oil.
Illustration 2 g02437998
Install connecting rod cap (2) to connecting rod (3). Note: Ensure that etched Number (X) on connecting rod cap (2) matches etched Number (X) on connecting rod (3). Ensure the correct orientation of the connecting rod cap. The locating tab for the upper bearing shell and the lower bearing shell should be on the same side.Note: Do not reuse the old connecting rod bolts in order to secure the connecting rod cap.
Install new bolts (1) to the connecting rod. Tighten the bolts evenly to a torque of 40 N m (30 lb ft).
Turn the bolts through an additional 120 degrees in a clockwise direction. Use Tooling (B) to achieve the correct final torque.
Ensure that the installed connecting rod assembly has tactile side play. Rotate the crankshaft in order to ensure that there is no binding.
Repeat Step 2 through Step 11 for the remaining connecting rod bearings. Note: If all connecting rod bearings require replacement, the procedure can be carried out on two cylinders at the same time. The procedure can be carried out on the following pairs of cylinders. 1 with 4 and 2 with 3. Ensure that both pairs of the connecting rod bearings are installed before changing from one pair of cylinders to another pair of cylinders. Refer to Disassembly and Assembly, "Connecting Rod Bearings - Install" for the correct procedure.
If the glow plugs were removed, install the glow plugs. Ref to Disassembly and Assembly, "Glow Plugs - Remove and Install" for the correct procedure. End By:
If the engine is equipped with a balancer, install the balancer. Refer to Disassembly and Assembly, "Balancer - Install" for the correct procedure.
If the engine is not equipped with a balancer, install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install" for the correct procedure.


Parts decal Force:

F286585-1
 
F286585-1 DECAL, TILT RELEASE (NOT SHOWN)
H0060B76A, H0060B78B, H0060H79C, H0060H80D, H0062B78J, H0062H79K, H0062H79M, H0064H80F, H0064H82H, H0067H79C, H0070B79A, H0071H81B, H0071H82C, H0071H83D, H0071H84E, H0072B81D, H0072H79B, H0072H80C, H0072H82E, H0075H79A, H0082H76G, H0082H78J, H0082H79
F510374
 
F510374 DECAL, CIRCUIT BREAKER
H0091B80B, H0091H79A, H0091H83C, H0092H79F, H0092H81H, H0092H81J, H0095B80F, H0095B81G, H0095H82H, H0101B78A, H0102H76C, H0102H78E, H0121B79A, H0122H79E, H0125H79E, H0152B78D, H0152B83J, H0152C84K, H0152H79E, H0202B81M, H0202H79K, H0252B83G, H0252H77
FA617396
 
FA617396 DECAL, "CHRYSLER", STARBOARD
H0091H83C, H0092H83K, H0092H84L
FA617386
 
FA617386 DECAL, NUMERAL
H0092H83K, H0092H84L
FA627396
 
FA627396 DECAL-STBD
H0091H84D, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H0152C84K, H0152S89A
F681396
 
F681396 DECAL-STARBOARD
H0091H84D, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H0152C84K, H0152S89A
F736528
 
F736528 DECAL-REAR
H0091H84D, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H0152C84K, H0152S89A
820731A95
 
820731A95 DECAL SET (9.9 FORCE)
H0091H84D, H009201SD, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H015211SS, H0152C84K, H0152S89A
Back to top