F462128 Force DRIVESHAFT FOR LONG SHAFT MODELS


F462128 DRIVESHAFT FOR LONG SHAFT MODELS Force H0306B80C, H0307H81D, H0350H78L, H0351H76K, H0357C86A, H0357C87A, H0357F88A, H0357H83N DRIVESHAFT
F462128 DRIVESHAFT FOR LONG SHAFT MODELS Force
Rating:
83

Buy DRIVESHAFT FOR LONG SHAFT MODELS F462128 Force genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$14.02
 

20-09-2017

Perfect Fi: Perfect Fit Group
Perfect Fit Group F462128 - F-Series Expedition Front Door Handle LH, Outside, Textured Black, W/ Keyhole
This Replacement Door Handle is made specifically to repair the original.||Partslink: FO1310119||Replaces OEM: 7L3Z1522405AA
Number on catalog scheme: -
 

Force entire parts catalog list:

H0306B80C 1980
H0307H81D 1981
H0350H78L 1978
H0351H76K 1976
H0357C86A 1986
H0357C87A 1987
H0357F88A 1988
H0357H83N 1983,1984

Information:


Table 1
Required Tools
Part Number Part Name Quantity
1U-5470
or
198-4240 Engine Pressure Group
or
Digital Pressure Indicator 1
Illustration 1 g00295554
1U-5470 Engine Pressure Group
Air Inlet Restriction
There will be a reduction in the performance of the engine if there is a restriction in the air inlet system.
Inspect the engine air cleaner inlet and ducting in order to ensure that the passageway is not blocked or collapsed.
Inspect the engine air cleaner element. Replace a dirty engine air cleaner element with a clean engine air cleaner element.
Check for dirt contamination on the clean side of the engine air cleaner element. If any dirt contamination is observed, contaminants are flowing past the engine air cleaner element and/or the seal for the engine air cleaner element.
Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool.
Making contact with a running engine can cause burns from hot parts and can cause injury from rotating parts.When working on an engine that is running, avoid contact with hot parts and rotating parts.
Use the differential pressure gauge of the 1U-5470 Engine Pressure Group.
Connect the vacuum port of the differential pressure gauge to the test location. The test location may be located anywhere along the air inlet piping after the air cleaner but before the turbocharger.
Leave the pressure port of the differential pressure gauge open to the atmosphere.
Start the engine. Run the engine in the no-load condition at high idle.
Record the value.
Multiply the value from Step 4.d by 1.8.
Compare the result from Step 4.e to the appropriate values that follow. The air flow through a used engine air cleaner may have a restriction. The air flow through a plugged engine air cleaner will be restricted to some magnitude. In either case, the restriction must not be more than the following amount: Maximum restriction ... 7.6 kPa (30.54 inch of H2O)The air flow through a new engine air cleaner element must not have a restriction of more than the following amount: Maximum restriction ... 3.7 kPa (14.87 inch of H2O)Exhaust Restriction
There will be a reduction in the performance of the engine if there is a restriction in the exhaust system.Back pressure is the difference in the pressure between the exhaust at the outlet elbow and the atmospheric air.
Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool.
Making contact with a running engine can cause burns from hot parts and can cause injury from rotating parts.When working on an engine that is running, avoid contact with hot parts and rotating parts.
Connect the pressure port of the differential pressure gauge to the test location. The test location can be located anywhere along the exhaust piping after the turbocharger but before the muffler.
Leave the vacuum port of the differential pressure gauge open to the atmosphere.
Start the engine. Run the engine in the no-load condition at high idle.
Record the value.
Multiply the value from Step 4 by 1.8.
Compare the result from Step 5 to the value that follows. Back pressure from the exhaust must not be more than the following amount: Maximum back pressure ... 6.8 kPa (27.33 inch of H2O)


Parts driveshaft Force:

F458128
 
F458128 DRIVESHAFT FOR STANDARD SHAFT MODELS
H0306B80C, H0350H78L, H0351H76K
FT8972
 
FT8972 DRIVESHAFT SEAL INSTALLER
H0202B80L, H0202B81M, H0202H79K, H0202H82N, H0252B83G, H0257F88A, H0257F88B, H0306B80C, H0307H81D, H0350H78L, H0351H76K, H0356F89B, H0357C86A, H0357C87A, H0357C88B, H0357F88A, H0357F89C, H0357H83N, H0407E92C, H0504H88C, H0504H88D, H0504P89B, H0505C89
Back to top