F502128 Force DRIVESHAFT FOR STANDARD SHAFT MODELS


F502128 DRIVESHAFT FOR STANDARD SHAFT MODELS Force H0202B80L, H0202B81M, H0202H79K, H0202H82N, H0252B83G DRIVESHAFT
F502128 DRIVESHAFT FOR STANDARD SHAFT MODELS Force
Rating:
33

Buy DRIVESHAFT FOR STANDARD SHAFT MODELS F502128 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 3
 

Force entire parts catalog list:

H0202B80L 1980
H0202B81M 1981
H0202H79K 1979
H0202H82N 1982
H0252B83G 1983,1984

Information:

Start By:a. remove exhaust manifoldb. remove rocker shaft assembly and push rods1. Drain the coolant from cooling system into a suitable container for storage or disposal. 2. Loosen clamps (3) and remove hose (1).3. Loosen clamps (4) and disconnect hose (2).4. Remove two bolts (5) that hold the water pump to the cylinder head.5. Unplug connector (6). Disconnect connector (7). 6. Remove bolts (11) and plate (9).7. Remove the four bolts, the washers, the cover, and the gasket from the rear opening on the cylinder head. Install Tool (A) and fasten a hoist.8. Remove twenty bolts (10) and seven bolts (8). Remove the cylinder head. The weight of the cylinder head assembly is approximately 177 kg (390 lbs).
Do not set the cylinder head on a flat surface because of possible damage to the fuel injection nozzle tips.
The following steps are for the installation of the cylinder head. When the cylinder head is removed, a new spacer plate gasket must be installed. See the topic "Remove & Install Spacer Plate".9. Make sure the surfaces that make contact between the cylinder head and cylinder block are clean and dry. Install a new gasket on the cylinder block.10. Install Tool (A) on the cylinder head and fasten a hoist. Put the cylinder head in position on the engine.11. Remove Tool (A). 12. Loosen the adjusting screws (13) on the rocker arms for valve clearance. This will prevent a bent valve or push rod during installation of the rocker shaft assembly.13. Install the push rods. The O-ring seal in the rear support must be installed new each time the bolt is removed from the rear support bracket.14. Put rocker shaft assembly (14) in position on the cylinder head.
Make sure the dowels on each end of the rocker shaft assembly are in alignment with the holes in the cylinder head.
15. Put 5P-0960 Molylube on all head bolts and washer faces. Install the rocker shaft bolts, bolts (8), and bolts (10) with the washers.16. Tighten the bolts as follows: a. Tighten bolts 1 through 26 in number sequence to a torque of 150 N m (110 lb ft).b. Tighten bolts 1 through 26 again in number sequence to a torque of 250 17 N m (185 13 lb ft).c. Tighten bolts A through G in letter sequence (hand tighten only) to a torque of 43 7 N m (32 5 lb ft).17. Make adjustments until the inlet valve clearance is 0.38 mm (.015 in) and the exhaust valve. Clearance is 0.64 mm (.025 in). See the topic "Valve Clearance Setting" in Testing & Adjusting. Tighten the locknuts for adjusting screw (13) to a torque of 29 7 N m (21 5 lb ft).18. Put the gasket and cover (12) in position on the cylinder head. Install the four bolts and washers.19. Put plate (9) in position and install bolts (11) and the washers.20. Install the gasket and two bolts (5) that hold the water pump to the cylinder head.21. Connect connector (6) and connector (7).22. Put hose (2) in position and tighten clamps (4).23. Put hose (1) in position and tighten clamps (3).24. Fill the cooling system with coolant to the proper level.End By:a. install rocker shaft assembly and push rodsb. install exhaust manifold


Parts driveshaft Force:

FT8972
 
FT8972 DRIVESHAFT SEAL INSTALLER
H0202B80L, H0202B81M, H0202H79K, H0202H82N, H0252B83G, H0257F88A, H0257F88B, H0306B80C, H0307H81D, H0350H78L, H0351H76K, H0356F89B, H0357C86A, H0357C87A, H0357C88B, H0357F88A, H0357F89C, H0357H83N, H0407E92C, H0504H88C, H0504H88D, H0504P89B, H0505C89
F503128
 
F503128 DRIVESHAFT FOR LONG SHAFT MODELS
H0202B80L, H0202B81M, H0202H79K, H0202H82N, H0252B83G
Back to top