F1947 Force FLANGED 12 PT. SCREW, 5/16 - 18 X 2


F1947 FLANGED 12 PT. SCREW, 5/16 - 18 X 2 Force H0352H77H, H0352H79L, H0353H78K, H0353H80M, H0353H81N, H0353H82P, H0356H75F, H0456B78J, H0456B79K, H0456B80L, H0457H82N, H0457H83P, H0503B83A, H0503H84B, H0507B85A, H0507C86A, H0507C87A, H0507C87C, H0507F87B, H0507F88A, H0507H81A, H0507H82B, H0555H74 FLANGED

Buy FLANGED 12 PT. SCREW, 5/16 - 18 X 2 F1947 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 8
 

Force entire parts catalog list:

H0352H77H 1977,1978
H0352H79L 1979
H0353H78K 1978
H0353H80M 1980
H0353H81N 1981
H0353H82P 1982
H0356H75F 1975,1976,1977
H0456B78J 1978
H0456B79K 1979
H0456B80L 1980,1981
H0457H82N 1982
H0457H83P 1983,1984
H0503B83A 1983
H0503H84B 1984
H0507B85A 1985
H0507C86A 1986
H0507C87A 1987
H0507C87C 1987
H0507F87B 1987
H0507F88A 1988
H0507H81A 1981
H0507H82B 1982
H0555H74G 1974,1976

Information:


Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00611180
Remove bolt (1) that holds the bracket for the engine speed/timing sensor to the timing gear housing. Remove two engine speed/timing sensors (3) and the bracket from the timing gear housing.
Cut the straps that hold the wiring harness to side cover (2) of the cylinder block.
Remove the bolts that hold side cover (2) to the cylinder block.
Illustration 2 g00611182
Remove the bolts and side covers (4) and (5) from the cylinder block.
Illustration 3 g00611184Note: Ensure that the sleeves of the side covers remain in the side covers.
Remove four bolts (6) and the dowels that hold the lifter arms (7) and the lifter shaft (8) to each side cover. Remove gasket (9). Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 4 g00611184
Install gasket (9).
Install lifter arms (7) on lifter shaft (8).
Position lifter shaft (8) and the dowels on the side cover. Ensure that the oil holes in the lifter shaft are facing the side cover. Apply 9S-3263 Thread Lock Compound on the threads of bolts (6) that hold lifter shaft (8) to the side cover. Install bolts (6). Tighten bolts (6) to a torque of 13 3 N m (10 2 lb ft). Tighten the two center bolts. Then tighten the end bolts.
Lubricate the lifters with clean engine oil.
Ensure that the cylinder block and the sealing surfaces of the side cover are thoroughly clean. Apply 1U-8846 Sealant to the sealing surfaces of the side cover. The side covers must be installed on the cylinder block within 10 minutes of applying the sealant.
Illustration 5 g00611182
Illustration 6 g00611180
Position the gaskets and side covers (2), (4), and (5) on the cylinder block. Install the bolts and clips that hold the side covers in position.
Install two engine speed/timing sensors (3) and the bracket to the timing gear housing. Install bolt (1).
Secure the two plugs of the wiring harness to the engine speed/timing sensors in the timing gear housing. Use new straps to hold the wiring harness to the side covers of the cylinder block. End By:
Install the electronic control module (ECM). Refer to Disassembly and Assembly, "Electronic Control Module - Remove and Install".
Install the air compressor (if equipped). Refer to Disassembly and Assembly, "Air Compressor - Remove and Install".
Install the unit injector hydraulic pump. Refer to Disassembly and Assembly, "Unit Injector Hydraulic Pump - Install".
Install the rocker arms and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Install".
Install the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base - Remove and Install".


Back to top