F10136 Force FLOAT LEVER PIN


F10136 FLOAT LEVER PIN Force H0252B83G, H0457H83P, H0503H84B, H0507B85A, H0606H84A, H0758H82E, H0856F84A, H0856F85A, H0856H82K, H0858C84H, H0906R83D, H1008H83C, H1058V83H, H1158H84G FLOAT
F10136 FLOAT LEVER PIN Force
Rating:
68

Buy FLOAT LEVER PIN F10136 Force genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$57.95
 

23-12-2023
6.0[2.70] pounds
US: Race-Driven Inc
Yellow Non O-Ring Chain & Silver Sprocket 15/40 100L 09-13 fits Yamaha YFZ450 YFZ 450
Race-Driven 15 Tooth Front Sprocket, 40 Tooth Rear Sprocket and 520-100L Yellow Non-O-Ring Chain || All Race-Driven sprockets meet or exceed OEM specifications and use hardened S45C steel. || Non-O-Ring chain doesn't have o-rings between the links so it is lighter, thinner and has less drag. || Fits 2009 2010 2011 2012 2013 Yamaha YFZ450
Number on catalog scheme: 23
 

Force entire parts catalog list:

H0252B83G 1983,1984
H0457H83P 1983,1984
H0503H84B 1984
H0507B85A 1985
H0606H84A 1984,1985,1989
H0758H82E 1982,1983,1984
H0856F84A 1984
H0856F85A 1985
H0856H82K 1982,1983
H0858C84H 1984
H0906R83D 1983,1984
H1008H83C 1983,1984
H1058V83H 1983
H1158H84G 1984

Information:


Table 1
Diagnostic Codes Table    
Description     Conditions which Generate this Code     System Response    
1599-5 Engine Fan Blade Position Pull Solenoid current below normal     The Electronic Control Module (ECM) detects current that is below normal.     The code is logged.
The fan control solenoid is disabled.    
1599-6 Engine Fan Blade Position Pull Solenoid current above normal     The ECM detects current that is above normal.     The code is logged.
The fan control solenoid is disabled.    
1600-5 Engine Fan Blade Position Push Solenoid current below normal     The ECM detects current that is below normal.     The code is logged.
The fan control solenoid is disabled.    
1600-6 Engine Fan Blade Position Push Solenoid current above normal     The ECM detects current that is above normal.     The code is logged.
The fan control solenoid is disabled.    The blades on the variable pitch fan can be placed into the following three positions:
Push
Pull
NeutralThe purpose of a variable pitch fan is to clean debris from the radiator. This is done by temporarily reversing the direction of the air flow through the radiator. Temporarily reversing the air flow through the radiator is called purging the radiator. An automatic purge of the radiator will occur after a length of time, and an automatic purge of the radiator will occur if the coolant reaches a certain temperature. The operator can manually purge the radiator by pressing the manual purge button.
Illustration 1 g01399962
SchematicTest Step 1. Inspect Electrical Connectors and Wiring
Remove electrical power from the ECM.
Illustration 2 g01139425
ECM (1) J1/P1 connectors (2) J2/P2 connectors
Thoroughly inspect ECM connector J1/P1, ECM connector J2/P2, and all other connectors in the wiring harness. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Illustration 3 g01399974
P1 terminals that are associated with the variable pitch fan (P1-19) Manual purge switch (P1-21) Pull solenoid (P1-29) Digital return (P1-27) Push solenoid
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector and the sensor connectors that are associated with the active diagnostic code.
Check the ECM connector (allen head screw) for the proper torque. Refer to Troubleshooting, "Electrical Connectors - Inspect".Expected Result:All connectors, pins, and sockets are completely inserted and coupled. The harness and wiring are free of corrosion, of abrasion, and of pinch points. All connections and grounds are tight and free of corrosion.Results:
OK - The harness and wiring are OK. Proceed to Test Step 2.
Not OK - There is a problem with the harness and/or wiring.Repair: Repair the circuit.Verify that the repair eliminates the problem.STOPTest Step 2. Check the Resistance through the Solenoid
Remove electrical power from the ECM.
Disconnect the push/pull solenoid for the variable pitch fan.
Measure the resistance between terminal 1 (push solenoid) and terminal 2 (digital return).
Measure the resistance between terminal 4 (pull solenoid) and terminal 3 (digital return).Expected Result:Resistance is 25 5 Ohms.Results:
OK - The push/pull solenoid for the variable pitch fan has the correct resistance. Proceed to Test Step 3.
Not OK - The resistance is not acceptable. The push/pull solenoid for the variable pitch fan is faulty.Repair: Install a new push/pull solenoid for the variable pitch fan.Verify that the repair eliminates the problem.STOPTest Step 3. Check the Status of the Manual Purge Switch
Connect Caterpillar Electronic Technician (ET) to the service tool connector.
Restore electrical power to the ECM.
Observe the status for "Engine Fan Manual Purge Switch" on Cat ET while you operate the switch.
Remove electrical power from the ECM.Expected Result:The status of the switch is "On" when the switch is depressed. The status reads "Off" when the switch is released.Results:
OK - The status shows the expected result. The manual purge switch is working properly. Proceed to Test Step 5.
Not OK - The status does not show the expected result. The ECM does not recognize the input from the manual purge switch. Proceed to Test Step 4.Test Step 4. Check the Manual Purge Switch
Remove electrical power from the ECM.
Disconnect the connector for the manual purge switch.
Measure the continuity between terminal B (manual purge


Parts float Force:

FO13944
 
FO13944 FLOAT LEVER PIN
H0033H75C, H005201RS, H005201SD, H005201TS, H005201UD, H0052C88A, H0060B76A, H0062H79M, H0064H78D, H0082H76G, H0082H79K, H0091B80B, H0091H79A, H0091H84D, H009201RS, H009201SD, H009201UD, H009201US, H0092284D, H0092B80G, H0092H79F, H0092H81H, H0092H84
FO13554
 
FO13554 FLOAT
H0033H75C, H005201RS, H0060B76A, H0062H79M, H0064H78D, H0082H76G, H0082H79K, H0091B80B, H0091H79A, H0092B80G, H0092H79F, H0092H81H, H0095B81G, H0101B78A, H0102H76C, H0102H78E, H0121B79A, H0122H79E, H0125H79E, H0152B78D, H0152H79E, H0152H80F, H0152H81
F10135
 
F10135 FLOAT
H0252B83G, H0257F88A, H0257F88B, H0355D89A, H0356F89B, H0357C86A, H0357C87A, H0357C88B, H0357F88A, H0457H83P, H0503H84B, H0504H88C, H0504H88D, H0504P89B, H0505C89B, H0507A89C, H0507B85A, H0507C86A, H0507C87A, H0507C87C, H0507C88B, H0507F87B, H0507F88
Back to top