F5H014 Force FLUSHING ADAPTER


F5H014 FLUSHING ADAPTER Force H0306B80C, H0350H78L, H0559H80N, H0756H81G, H0756H82H, H0757H78D, H0850H79A, H0850H80A, H0850H81C, H0851H79A, H0855H79A, H0856B80H, H0857B78F, H0857H79G, H0858B80C, H0858B82E, H0859B79B, H1000H79A, H1004H79A, H1006B80B, H1006B81C, H1007H79A, H1008H80 FLUSHING
F5H014 FLUSHING ADAPTER Force
Rating:
78

Buy FLUSHING ADAPTER F5H014 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: &nbsp
 

Force entire parts catalog list:

H0306B80C 1980
H0350H78L 1978
H0559H80N 1980,1981
H0756H81G 1981
H0756H82H 1982
H0757H78D 1978
H0850H79A 1979
H0850H80A 1980
H0850H81C 1981
H0851H79A 1979
H0855H79A 1979
H0856B80H 1980
H0857B78F 1978
H0857H79G 1979
H0858B80C 1980
H0858B82E 1982
H0859B79B 1979
H1000H79A 1979
H1004H79A 1979
H1006B80B 1980
H1006B81C 1981
H1007H79A 1979
H1008H80A 1980
H1057B78H 1978
H1058H82G 1982
H1150H79A 1979
H1151H79A 1979
H1154B79A 1979
H1155H79A 1979
H1156H80C 1980
H1156H81D 1981
H1157B79B 1979
H1157H78A 1978
H1158B82E 1982
H1158H80D 1980
H1159H79C 1979
H1251F84A 1984
H1258H81A 1981,1982
H1400H79A 1979
H1401H79A 1979
H1405H79A 1979
H1406H80C 1980
H1406H81D 1981
H1407B79B 1979
H1408B80C 1980
H1408H82D 1982
H1409H79B 1979

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A - Guide Bolt
(M16 by 115mm) 2
B 8T-3052 Degree Wheel 1
C 1U-6396 O-Ring Assembly Compound 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Thoroughly clean the mating surfaces of the cylinder head and the cylinder block. Do not damage the mating surfaces of the cylinder head of the cylinder block. Ensure that no debris enters the cylinder bores, the coolant passages, or the lubricant passages.
Inspect the mating surface of the cylinder head for distortion. Refer to Specifications, "Cylinder Head" for more information. If the mating surface of the cylinder head is distorted beyond maximum permitted limits, replace the cylinder head.
If necessary, install the inlet manifold to the cylinder head. Refer to Disassembly and Assembly, "Inlet manifold - Remove and Install".
Illustration 1 g01340176
Inspect dowels (18) for damage. If necessary, replace the dowels in the cylinder block.
Install Tooling (A) to the cylinder block.
Align cylinder head gasket (17) with dowels (18). Install cylinder head gasket (17) onto the cylinder block.
Illustration 2 g01340086
Typical example
Use a suitable lifting device (16) to lift cylinder head (15). The weight of the cylinder head is approximately 66 kg (145.5 lb). Note: A spreader bar must be used in order to distribute the weight of the cylinder head during the lifting operation.
Use Tooling (A) to align the cylinder head with the cylinder block. Install the cylinder head to the cylinder block. Note: Ensure that the cylinder head is correctly positioned on dowels (18).
Remove Tooling (A).
Illustration 3 g01340188
Clean bolts (14). Follow Steps 10.a for the procedure to inspect the bolts.
Use a straight edge to check the threads of the bolts. Refer to Illustration 3. Replace any bolts that show visual reduction in the diameter of the thread over length (Y).
Lubricate the threads and the shoulder of bolts (14) with clean engine oil.
Illustration 4 g01340081
Illustration 5 g01340192
Install bolts (14) to cylinder head (16).
Tighten the bolts to a torque of 50 N m (37 lb ft) in the numerical sequence. Refer to Illustration 5.
Tighten the bolts to a torque of 100 N m (74 lb ft) in the numerical sequence. Refer to Illustration 5.
Turn the bolts through an additional 225 degrees in the numerical sequence. Refer to Illustration 5. Use Tooling (B) to achieve the correct final torque.
Illustration 6 g01340080
Typical example
Use Tooling (C) in order to lubricate the O-ring seals. Install new O-ring seals (12) and (13) to bypass tube (11). Install the bypass tube in the cylinder head. Install bolts (10). Tighten the bolts to a torque of 22 N m (16 lb ft).
Illustration 7 g01340077
Typical example
Remove the plugs and caps from the ports and tube assemblies.
Install tube assembly (8) for the fuel return to the cylinder head and to the transfer pump. Secure the tube clips for tube assembly (8).
If the engine has a wastegate solenoid, install tube assembly (9) for the wastegate solenoid to the cylinder head. Secure the tube clips for tube assembly (9).
Illustration 8 g01340075
Typical example
Follow Steps 20.a and 20.b in order to connect harness assembly (4) to inlet air temperature sensor (7).
Connect harness assembly (4) to inlet air temperature sensor (7).
Slide the locking tab into the locked position.
Follow Steps 21.a and 21.b in order to connect harness assembly (4) to boost pressure sensor (6).
Connect harness assembly (4) to boost pressure sensor (6).
Slide the locking tab into the locked position.
Follow Steps 22.a and 22.b in order to connect harness assembly (4) to coolant temperature sensor (5).
Connect harness assembly (4) to coolant temperature sensor (5).
Slide the locking tab into the locked position.
Use new cable straps in order to secure the harness assembly to the cylinder head and to the inlet manifold. Ensure that the harne


Parts flushing Force:

F5H013
 
F5H013 FLUSHING ADAPTER
H0060H79C, H0060H80D, H0070B79A, H0071H81B, H0071H82C, H0071H83D, H0075H79A, H0091B80B, H0091H79A, H0091H83C, H0091H84D, H0095B81G, H0095H82H, H0101B78A, H0121B79A, H0125H79E, H1157H78A
Back to top