F318154 Force GASKET, EXHAUST COVER


F318154 GASKET, EXHAUST COVER Force H0060B76A, H0062H79M, H0064H78D, H0082H76G, H0082H79K GASKET
F318154 GASKET, EXHAUST COVER Force
Rating:
93

Buy GASKET, EXHAUST COVER F318154 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 46
 

Force entire parts catalog list:

H0060B76A 1976
H0062H79M 1979
H0064H78D 1978
H0082H76G 1976,1977
H0082H79K 1979

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 370-8376 Capping Kit 1
Contact with high pressure fuel may cause fluid penetration and burn hazards. High pressure fuel spray may cause a fire hazard. Failure to follow these inspection, maintenance and service instructions may cause personal injury or death.
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information. Refer to System Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Turn the fuel supply to the OFF position.
Turn the battery disconnect switch to the OFF position.
If necessary, remove fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base - Remove and Install" for the correct procedure.
If necessary, remove crankcase breather canister filter. Refer to Operation and Maintenance Manual, "Engine Crankcase Breather Element - Replace" for the correct procedure.
Illustration 1 g03585598
Clean the area around flow control valve (3) and fuel injection pump (1). Ensure that the area is free from contamination before beginning disassembly.
Disconnect harness assembly (4) from flow control valve (3).
Make temporary marks on flow control valve (3) and the fuel injection pump for installation purpose.
Remove allen heads screws (2) from flow control valve (3).
Remove flow control valve (3) from fuel injection pump (1).
Use Tooling (A) to plug fuel injection pump (1).
Remove O-ring seal (5) and O-ring seal (6).
Use Tooling (A) to cap flow control valve (3). Installation Procedure
Ensure that all component at free from wear and damage. If any part of the flow control valve is worn or damaged, the flow control valve must be replaced as an assembly.
Illustration 2 g03585598
Illustration 3 g03411799
Flow control valve guide pins
Remove cap from flow control valve (3). Position new O-ring seal (5) and new O-ring seal (6) onto flow control valve (3).
Install guide pins into Position (X) on fuel injection pump (1).
Lubricate O-ring seal (5) and O-ring seal (6) with clean fuel. Note: Ensure that the O-ring seal is not damaged or misaligned.
Remove plug from fuel injection pump (1). Align flow control valve (3) onto guide pins.
Install flow control valve (3) to fuel injection pump (1).
Remove guide pins from the fuel injection pump.
Install allen head screws (2) from the flow control valve repair kit.
Tighten allen head screws (2) equally until the flow control valve is seated correctly onto the fuel injection pump. Note: Ensure that the allen screws are tightened equally. Failure to ensure that the allen screws are tightened equally will result in damage to the fuel injection pump.
Tighten allen head screws (2) to a torque of 9 N m (80 lb in).
Connect harness assembly (4) to flow control valve (3).
Replace the filters for primary fuel system. Refer to Operation and Maintenance Manual, "Fuel System Primary (Water Separator) Element - Replace" for the correct procedure.
Replace the filters for secondary fuel system. Refer to Operation and Maintenance Manual, "Fuel System Secondary Filter - Replace" for the correct procedure.
Turn the fuel supply to the ON position.
Turn the battery disconnect switch to the ON position.
Remove the air from the fuel system. Refer to Operation and Maintenance Manual, "Fuel System - Prime" for more information. End By:
Remove the air from the fuel system. Refer to Operation and Maintenance Manual, "Fuel System - Prime" for the correct procedure.
After replacement of the flow control valve, the fuel injection pump requires a high-pressure fuel pump calibration procedure to be performed. Refer to Troubleshooting, "Fuel Rail Pressure Problem" for the correct procedure.


Parts gasket Force:

F10006
GASKET SET
F10006 GASKET SET
H0033H75C, H0060B76A, H0062H79M, H0064H78D, H0082H76G, H0082H79K, H0091B80B, H0091H79A, H0092B80G, H0092H79F, H0095B80F, H0101B78A, H0102H76C, H0102H78E, H0121B79A, H0122H79E, H0125H79E, H0152B78D, H0152H79E, H0152H80F
F318453-1
 
F318453-1 GASKET, LEG MOUNTING
H0060B76A, H0062H79M, H0064H78D, H0082H76G, H0082H79K
F24748-2
 
F24748-2 GASKET, FUEL PUMP COVER
H005201RS, H005201SD, H005201TS, H005201UD, H0052C88A, H0060B76A, H0060B78B, H0060H79C, H0060H80D, H0062B78J, H0062H79K, H0062H79M, H0064H78D, H0064H80F, H0064H82H, H0067H79C, H0070B79A, H0071H81B, H0071H82C, H0071H83D, H0071H84E, H0072B81D, H0072H79
F318168
 
F318168 GASKET, MANIFOLD
H0060B76A, H0062H79M, H0064H78D, H0082H76G, H0082H79K
F318159
 
F318159 GASKET, REED PLATE
H0060B76A, H0062H79M, H0064H78D, H0082H76G, H0082H79K
F318967
 
F318967 GASKET, SHOCK MOUNT PLATE
H0060B76A, H0062H79M, H0064H78D, H0082H76G, H0082H79K
F429472
 
F429472 GASKET, CYLINDER DRAIN COVER
H0060B76A, H0062H79M, H0064H78D, H0082H76G, H0082H79K, H0091B80B, H0091H79A, H0091H83C, H0091H84D, H0092284D, H0092B80G, H0092H79F, H0092H81H, H0092H81J, H0092H83K, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H0094H81F, H0095B80F, H0095B81G, H0095H82
F318223-1
 
F318223-1 GASKET, TRANSFER PORT COVER
H0060B76A, H0062H79M, H0064H78D, H0082H76G, H0082H79K
Back to top