F525529 Force GASKET, CYLINDER HEAD


F525529 GASKET, CYLINDER HEAD Force H0060B78B, H0060H79C, H0060H80D, H0062B78J, H0062H79K, H0064H80F, H0064H82H, H0067H79C, H0070B79A, H0071H81B, H0071H82C, H0071H83D, H0071H84E, H0072B81D, H0072H79B, H0072H80C, H0072H82E, H0075H79A, H0082H78J GASKET
F525529 GASKET, CYLINDER HEAD Force
Rating:
33

Buy GASKET, CYLINDER HEAD F525529 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: &nbsp
 

Force entire parts catalog list:

H0060B78B 1978
H0060H79C 1979
H0060H80D 1980
H0062B78J 1978
H0062H79K 1979
H0064H80F 1980
H0064H82H 1982
H0067H79C 1979
H0070B79A 1979
H0071H81B 1981
H0071H82C 1982
H0071H83D 1983
H0071H84E 1984,1985
H0072B81D 1981
H0072H79B 1979
H0072H80C 1980
H0072H82E 1982
H0075H79A 1979
H0082H78J 1978

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Gp 1
B - Loctite LB 8028 Camshaft Lube -
C - Loctite Superflex Silicone Adhesive Sealant, Blue -
D - Loctite 242 -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Do not turn the crankshaft or the camshaft while the camshaft gear is removed. If the front gear group is not correctly timed during installation, interference can occur between the pistons and the valves, resulting in damage to the engine.
Thoroughly clean the gasket material from the cylinder block and both sides of the plate.
Illustration 1 g01101567
If studs (24) are loose or the threads are damaged, install new studs (24) in the front plate. Apply Tooling (D) to the serrations of studs (24). Install studs (24) in the front plate.
Install integral seal (25) on the dowel pins on the cylinder block.Note: Apply Tooling (C) to the bottom of integral seal (25) in order to fill the space at the cylinder block, the front housing, and the engine oil pan.
Install plate (22) on the dowel pins on the cylinder block. Install new locking bolts (23) (Marked "X") in order to fasten the front plate to the cylinder block. Tighten locking bolts (23) to a torque of 55 N m (41 lb ft).Note: Clean the old sealant from the bolts and apply Tooling (D) to the bolts.
Tighten locking bolts (23) again to a torque of 55 N m (41 lb ft).
Illustration 2 g01239343
Install stub shaft (18). Apply Tooling (D) to the studs and the bolt for stub shaft (18). Tighten nuts (19) and the bolt to a torque of 55 10 N m (41 7 lb ft).
Install stub shaft assembly (16). Apply Tooling (D) to the studs and the bolt for stub shaft assembly (16). Do not tighten nuts (17) and the bolt for stub shaft assembly (16) at this time. Nuts (17) and the bolt for stub shaft assembly (16) will need to be tightened when the backlash is adjusted.
Adjust the backlash between the camshaft gear and the adjustable idler gear assembly. The backlash should be 0.356 0.254 mm (0.014 0.010 inch). Refer to Testing and Adjusting, "Gear Group (Front) - Time" for the backlash adjustment procedure. Tighten nuts (17) and the bolt to a torque of 55 10 N m (41 7 lb ft).
Install stub shaft (20). Apply Tooling (D) to bolts (21). Install bolts (21) and tighten in a numeric sequence 1, 3, 4, 5, 2, 1, 2, 3, 4, 5, 1 to a torque of 55 10 N m (41 7 lb ft).
Illustration 3 g01239302
Use Tooling (A) to install the sleeve bearing in cluster gear assembly (13).
Put cluster gear assembly (13) on the stub shaft. Ensure that Timing Marks (V) are aligned on the cluster gear assembly and the crankshaft gear.
Position plate (15) with the oil groove toward the face of the gear. Apply Tooling (D) to bolts (14). Install bolts (14). Tighten bolts (14) to a torque of 30 7 N m (22 5 lb ft).
Illustration 4 g01239267
Use Tooling (A) to install the sleeve bearing in idler gear (10) and adjustable idler gear (7).Note: Align the oil hole in the bearing with the oil hole in the adjustable idler gear.
Put idler gear assembly (10) on the stub shaft. Install plate (12) with the oil groove toward the gear face. Apply Tooling (D) to bolts (11). Install bolts (11). Tighten bolts (11) to a torque of 30 7 N m (22 5 lb ft).
Put adjustable idler gear assembly (7) on the stub shaft assembly. Position plate (9) with the oil groove toward the face of the gear. Apply Tooling (D) to bolts (8). Install bolts (8). Tighten bolts (8) to a torque of 30 7 N m (22 5 lb ft).Note: Check the backlash for the camshaft gear and the adjustable idler gear assembly. The camshaft gear must be installed and the adjustable idler gear assembly must be removed in order to perform the backlash adjustment procedure. Refer to Testing and Adjusting, "Gear Group (Front) - Time".
Illustration 5 g01008431
Install O-ring seal (5) and O-ring seal (6) in sealing plate (3). Lubricate O-ring seal (6) with a 50/50 mixture of Tooling (B) and clean engine oil.
Illustration 6 g01008430
Illustration 7 g01008429
Install adapter (4). Ensure that the dowel in the adapter engages the hole in the camshaft.


Parts gasket Force:

F24748-2
 
F24748-2 GASKET, FUEL PUMP COVER
H005201RS, H005201SD, H005201TS, H005201UD, H0052C88A, H0060B76A, H0060B78B, H0060H79C, H0060H80D, H0062B78J, H0062H79K, H0062H79M, H0064H78D, H0064H80F, H0064H82H, H0067H79C, H0070B79A, H0071H81B, H0071H82C, H0071H83D, H0071H84E, H0072B81D, H0072H79
F286277
 
F286277 GASKET, CRANKSHAFT BEARING CAGE
H0060B76A, H0060B78B, H0060H79C, H0060H80D, H0062B78J, H0062H79K, H0062H79M, H0064H78D, H0064H80F, H0064H82H, H0067H79C, H0070B79A, H0071H81B, H0071H82C, H0071H83D, H0071H84E, H0072B81D, H0072H79B, H0072H80C, H0072H82E, H0075H79A, H0082H76G, H0082H78
F10066
 
F10066 GASKET, VALVE SEAT
H0032H84G, H0042081C, H0042082D, H0042083E, H0042B78C, H0042B80G, H0042C84L, H0042C87A, H0042H77B, H0042H78D, H0042H78E, H0042H79F, H0043F85A, H0052C88A, H0060B78B, H0060H79C, H0060H80D, H0062B78J, H0062H79K, H0064H80F, H0064H82H, H0067H79C, H0070B79
F10068
 
F10068 GASKET, FUEL BOWL
H0032H84G, H0042081C, H0042082D, H0042083E, H0042B78C, H0042B80G, H0042C84L, H0042C87A, H0042H77B, H0042H78D, H0042H78E, H0042H79F, H0043F85A, H0052C88A, H0060B78B, H0060H79C, H0060H80D, H0062B78J, H0062H79K, H0064H80F, H0064H82H, H0067H79C, H0070B79
F10069
 
F10069 GASKET SET
H0032H84G, H0042081C, H0042082D, H0042083E, H0042B78C, H0042B80G, H0042C87A, H0042H77B, H0042H78D, H0042H78E, H0042H79F, H0060B78B, H0060H79C, H0060H80D, H0062B78J, H0062H79K, H0064H80F, H0064H82H, H0067H79C, H0070B79A, H0071H81B, H0071H82C, H0071H83
F525159
 
F525159 GASKET, REED PLATE
H0060B78B, H0060H79C, H0060H80D, H0062B78J, H0062H79K, H0064H80F, H0064H82H, H0067H79C, H0070B79A, H0071H81B, H0071H82C, H0071H83D, H0071H84E, H0072B81D, H0072H79B, H0072H80C, H0072H82E, H0075H79A, H0082H78J
F525168
 
F525168 GASKET MANIFOLD
H0060B78B, H0060H79C, H0060H80D, H0062B78J, H0062H79K, H0064H80F, H0064H82H, H0067H79C, H0070B79A, H0071H81B, H0071H82C, H0071H83D, H0071H84E, H0072B81D, H0072H79B, H0072H80C, H0072H82E, H0075H79A, H0082H78J
F10090
 
F10090 GASKET FUEL BOWL RETAINER
H0032H84G, H0042081C, H0042082D, H0042083E, H0042B80G, H0042C84L, H0042C87A, H0042H79F, H0043F85A, H0052C88A, H0060B78B, H0060H79C, H0060H80D, H0062B78J, H0062H79K, H0064H80F, H0064H82H, H0067H79C, H0070B79A, H0071H81B, H0071H82C, H0071H83D, H0071H84
Back to top