F658803 Force GASKET, SPACER PLATE


F658803 GASKET, SPACER PLATE Force H0407E92C, H0504H88C, H0504H88D, H0504P89B, H0505C89B, H0507A89C, H0507A89D, H0507A90A, H0507A90B, H0507A90C, H0507A90D, H0507A91A, H0507A91C, H0507A92A, H0507C87A, H0507C87C, H0507C88B, H0507E91B, H0507F87B, H0507F88A, H0507Z89B, H0706A91B, H0851X88 GASKET
F658803 GASKET, SPACER PLATE Force
Rating:
63

Buy GASKET, SPACER PLATE F658803 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 3
 

Force entire parts catalog list:

H0407E92C 1992,1993,1994
H0504H88C 1988
H0504H88D 1988
H0504P89B 1989
H0505C89B 1989
H0507A89C 1989
H0507A89D 1989
H0507A90A 1990
H0507A90B 1990
H0507A90C 1990
H0507A90D 1990
H0507A91A 1991
H0507A91C 1991
H0507A92A 1992
H0507C87A 1987
H0507C87C 1987
H0507C88B 1988
H0507E91B 1991
H0507F87B 1987
H0507F88A 1988
H0507Z89B 1989
H0706A91B 1991,1992,1993,1994,1995
H0851X88A 1988
H0853F88B 1988,1989
H0853F89C 1989
H0853F89E 1989
H0853F89F 1989
H0853F89G 1989
H0856A89A 1989
H0856A89H 1989
H0856C87A 1987
H0856C87B 1987
H0856L89D 1989
H0856Y89B 1989
H085LD89A 1989
H085LD89B 1989
H085LD89C 1989
H0903E91D 1991
H0903E91H 1991,1992,1993,1994
H0903F90B 1990
H0903F90C 1990
H0903F91A 1991
H0903F91C 1991
H0906A90A 1990
H090LD90A 1990
H090LD90B 1990,1991
H090LD90C 1990
H090LD91D 1991
H1201A90A 1990,1991,1992,1993,1994
H120LD90A 1990
H120LD90B 1990
H120LD90C 1990
H120LD91B 1991
H120LD91D 1991
H120LD92B 1992
H1251A88A 1988
H1251A88B 1988
H1251A88C 1988
H1251A89A 1989
H1251A89B 1989
H1251A89C 1989
H1251A89D 1989
H1251A89E 1989
H1251F87A 1987
H1251F87B 1987
H125LD89A 1989
H125LD89B 1989
H1501E89A 1989,1990,1991,1992,1993,1994

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 589-7433 Link Bracket 2
B - Loctite ® C5-A (North America) -
Loctite ® 8008 (Outside North America) -
C 207-1601 Rubber Lubricant 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the spacer plate and the surface of the cylinder block are clean.
Illustration 1 g06553514
Ensure that the surface of the spacer plate gasket and the surface of the cylinder block are clean. Do not use a gasket adhesive on these surfaces.
Install a new gasket (18) on the dowels in the cylinder block.
Install O-ring seal (19).
Illustration 2 g06553497
Install spacer plate (17) and cylinder head gasket (16) on the dowels in the cylinder block.
Check the cylinder liner projection. Refer to Testing and Adjusting, "Cylinder Liner Projection" for the correct procedure.
Illustration 3 g06553298
Install seals (13) and seals (14).
Apply Tooling (C) to the bore of the inlet tube assembly. Install O-ring seal (11) in the inlet tube assembly.
Install gasket (12) on the exhaust manifold.
Install O-ring seal (15) on the dowel.
Illustration 4 g06554112
Install plug (20).
Illustration 5 g06554127
Install Tooling (A) onto cylinder head assembly (10). Attach a suitable lifting device to Tooling (A). The weight of cylinder head assembly (7) is approximately 47 kg (104 lb).
Ensure that the bottom of the cylinder head assembly is thoroughly clean.
Illustration 6 g06552788
Lift the cylinder head assembly into position on the cylinder block. Install bolts (8) and bolts (9) according to the instructions in Step 15 or Step 16.Note: Only 216 mm (8.5 inch) bolts (8) can be used for the following torque procedures.Note: Refer to Specifications, "Cylinder Head".
Remove Tooling (A) from the cylinder head.
Illustration 7 g06554187
Tightening sequence with 362-8264 Cylinder Head Gasket (MLS) and 519-7297 Spacer Plate (Iron).Note: Refer to Illustration 7 for the correct tightening sequence.
Coat the threads of the bolts with clean engine oil.
Tighten bolt (1) through bolt (8) to a torque of 30 5 N m (22 4 lb ft).
Tighten bolt (1) through bolt (8) to a torque of 145 15 N m (107 11 lb ft).
Tighten bolt (1) through bolt (8) to a torque of 145 15 N m (107 11 lb ft).
Turn bolt (1) through bolt (8) an angle of 180 5 degrees.
Tighten bolts (9) and (10) to a torque of 55 10 N m (40 7 lb ft).
Illustration 8 g06554195
Tightening sequence with 110-6991 Cylinder Head Gasket (Cellulose) and 110-6994 Spacer Plate (Aluminum) or 362-9677 Spacer Plate (Aluminum).Note: The cellulose head gasket cannot be used with an iron spacer plate.Note: Refer to Illustration 8 for the correct tightening sequence.
Tighten bolt (1) through bolt (8) to a torque of 30 5 N m (22 4 lb ft).
Tighten bolt (1) through bolt (8) to a torque of 200 15 N m (148 11 lb ft).
Tighten bolt (1) through bolt (8) again to a torque of 200 15 N m (148 11 lb ft).
Turn bolt (1) through bolt (8) to an angle of 180 degrees.
Tighten bolt (9) and bolt (10) to a torque of 55 10 N m (41 7 lb ft).


Parts gasket Force:

FG1007-1
 
FG1007-1 GASKET SET (NOT SHOWN)
H0352H77H, H0352H79L, H0353H78K, H0353H80M, H0353H81N, H0353H82P, H0356H75F, H0456B78J, H0456B79K, H0456B80L, H0457H82N, H0457H83P, H0503H84B, H0507B85A, H0507C86A, H0507C87A, H0507H81A, H0507H82B, H0555H74G
F85748-2
 
F85748-2 GASKET, CYLINDER DRAIN REED PLATE
H0700H79A, H0706A91B, H0709B79A, H0750H79A, H0756H80F, H0756H81G, H0756H82H, H0757B79E, H0757H75A, H0757H76C, H0757H78D, H0758H80B, H0758H82E, H0759H79A, H0850H79A, H0850H80A, H0850H81C, H0851H79A, H0851X88A, H0853F88B, H0853F89C, H0853F89E, H0853F89
FG1019
 
FG1019 GASKET SET
H0906R83D, H1006B80B, H1006B81C, H1008H80A, H1008H83C, H1058H82G, H1058V83H, H1156H80C, H1158B82E, H1158H80D, H1158H84G, H1251A88A, H1251A88B, H1251F84A, H1251F86A, H1251F87A, H1251F87B, H1251X85A, H1258H81A, H1406H81D, H1408B80C, H1408H82D, H1408H83
F17602
 
F17602 GASKET PACKAGE
H0507C87C, H0507F87B
FG1028
 
FG1028 GASKET SET
H0853F89C, H0853F89E, H0853F89F, H0853F89G, H0856A89H, H0856L89D, H085LD89A, H085LD89B, H085LD89C, H0903F90B, H0906A90A, H090LD90A
FG1033
GASKET SET
FG1033 GASKET SET
H0507A90C, H0507A90D, H0507A91A, H0507A92A
FG1026-2
 
FG1026-2 GASKET SET
H1201A90A, H120LD91D, H120LD92B
Back to top