817817A 3 Force GEAR HOUSING UPPER W/BEARING, SEALS, WASHER AND PLUG


817817A 3 GEAR HOUSING UPPER W/BEARING, SEALS, WASHER AND PLUG Force H0060B76A, H0060B78B, H0060H79C, H0060H80D, H0064H80F, H0070B79A, H0071H81B, H0071H82C, H0071H83D GEAR
817817A 3 GEAR HOUSING UPPER W/BEARING, SEALS, WASHER AND PLUG Force
Rating:
33

Buy GEAR HOUSING UPPER W/BEARING, SEALS, WASHER AND PLUG 817817A 3 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 16
 

Force entire parts catalog list:

H0060B76A 1976
H0060B78B 1978
H0060H79C 1979
H0060H80D 1980
H0064H80F 1980
H0070B79A 1979
H0071H81B 1981
H0071H82C 1982
H0071H83D 1983

Information:


Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
ZZ     6V-9512     Face Seal Plug     1    
6V-9833 Cap As     1    
6V-9507 Face Seal Plug     1    
6V-9828 Cap As     1    
5P-2909 Plug     1    
8S-4951 Cap     1    
6V-9509 Face Seal Plug     1    
6V-9830 Cap As     1    
6V-7496 Tapered Cap/Plug     1    Start By:
Remove the fuel tank. Refer to Disassembly and Assembly, "Fuel Tank (Left Side) - Remove".Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.Note: SERVICE DATA: TOOLING (ZZ) WILL NOT BE IDENTIFIED IN PHOTOGRAPHS IN THE REMOVAL OR THE INSTALLATION. THIS TOOLING IS SHOWN IN ORDER TO ASSIST THE EXPERIENCED SERVICEMAN.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Drain the cooling system. Refer to Operation and Maintenance Manual, "Cooling System Level - Check" for the correct procedure.
Drain the coolant from the cooling system into a suitable container for storage or disposal.
Illustration 1 g01020095
Remove clip (1). Remove tube assembly (2) .
Illustration 2 g01020097
Disconnect hose assembly (3) .
Disconnect hose assembly (4) .
Disconnect tube assembly (5) .
Disconnect hose assemblies (6) .
Illustration 3 g01020117
Attach a suitable lifting device to air compressor (7). The weight of air compressor (7) is approximately 23 kg (50 lb).
Remove bolts (8) .
Remove air compressor (7) .Installation Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
Illustration 4 g01020117
Attach a suitable lifting device to air compressor (7). The weight of air compressor (7) is approximately 23 kg (50 lb).
Install air compressor (7) .
Install bolts (8) .
Illustration 5 g01020097
Connect hose assemblies (6) .
Connect tube assembly (5) .
Connect hose assembly (4) .
Connect hose assembly (3) .
Illustration 6 g01020095
Install tube assembly (2). Install clip (1) .
Fill the cooling system. Refer to Operation and Maintenance Manual, "Cooling System Level - Check" for the correct procedure.End By: Install the fuel tank. Refer to Disassembly and Assembly, "Fuel Tank (Left Side) - Install".


Parts gear Force:

F318611-1
 
F318611-1 GEAR SHIFT ROD
H0060B76A, H0062H79M, H0082H76G, H0082H79K
F318876-1
 
F318876-1 GEAR SHIFT LEVER
H0060B76A, H0062H79M, H0064H78D, H0082H76G, H0082H79K
F286614
 
F286614 GEAR SHIFT HANDLE
H0060B76A, H0062H79M, H0082H76G, H0082H79K, H0091B80B, H0091H79A, H0091H83C, H0091H84D, H0092284D, H0092B80G, H0092H79F, H0092H81H, H0092H81J, H0092H83K, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H0094H81F, H0101B78A, H0102H76C, H0102H78E, H0121B79
F487417
 
F487417 GEAR SHIFT HANDLE SHAFT
H0060B76A, H0062H79M, H0082H76G, H0082H79K
FA516554
 
FA516554 GEAR HOUSING UPPER W/BEARING, SEALS, WASHER AND PLUG
H0060B78B, H0060H79C, H0060H80D, H0064H80F, H0070B79A, H0075H79A
F498891
 
F498891 GEAR SHIFT ARM PIN
H0060B78B, H0060H79C, H0060H80D, H0064H80F, H0070B79A, H0071H81B, H0071H82C, H0071H83D, H0075H79A, H0091B80B, H0091H79A, H0091H83C, H0091H84D, H0095B80F, H0095B81G, H0095H82H, H0101B78A, H0121B79A, H0125H79E, H0202B80L, H0202B81M, H0202H79K, H0202H82
F90871-3
 
F90871-3 GEAR SHIFT ARM PIN
H0060B78B, H0060H79C, H0060H80D, H0064H80F, H0070B79A, H0071H81B, H0071H82C, H0071H83D, H0075H79A, H0091B80B, H0091H79A, H0091H83C, H0091H84D, H0095B80F, H0095B81G, H0095H82H, H0101B78A, H0121B79A, H0125H79E, H0202B80L, H0202B81M, H0202H79K, H0202H82
F525674
 
F525674 GEAR STARTER PINION
H0060B78B, H0062B78J, H0062H79K, H0070B79A, H0072H79B, H0072H80C, H0082H78J
Back to top