818059A 1 Force GEAR SHIFT ROD


818059A 1 GEAR SHIFT ROD Force H0352H77H, H0352H79L, H0353H78K, H0353H80M, H0353H81N, H0353H82P GEAR
818059A 1 GEAR SHIFT ROD Force
Rating:
63

Buy GEAR SHIFT ROD 818059A 1 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 28
 

Force entire parts catalog list:

H0352H77H 1977,1978
H0352H79L 1979
H0353H78K 1978
H0353H80M 1980
H0353H81N 1981
H0353H82P 1982

Information:


Table 1
Engine Arrangement
Original Engine Replacement Engine
4N-8330
2W-5258 257-6350(1)
(1) New Repower EngineThis Special Instruction does not include procedures that can be found in your existing manuals. Refer to the original Service Manual, Parts Manual, and Operation and Maintenance Manual for more information.When you have completed this procedure, prepare the machine for service. Refer to the Operation and Maintenance Manual.Note: Do not perform any procedure in this Special Instruction until the information has been read and understood.Reference: Service Manual, Parts Manual, Operation and Maintenance Manual.Note: This instruction contains some procedures that come from dealer feedback. The emissions replacement engine is not a direct replacement. Additional parts and additional labor hours may be needed to complete this engine replacement. Variations in machine serial number breaks or options could cause a discrepancy in the modifications, parts needed, and labor hours to complete this repower. This documentation is a guideline for Caterpillar dealer personnel to complete the repower procedure. If errors are found, submit feedback in SIS Web or contact the Emissions Retrofit Group.
Machine serial number
Original engine arrangement number
Original engine serial number
Emissions engine arrangement number
Details of the error
Photos of the error and photos after the proposed solutionRegistering the Retrofit
Reference: Special Instruction, REHS5097, "Instructions to Register the Retrofit"Documenting changes to a machine configuration is an advantage to Caterpillar and the dealer technicians that are sent to repair a machine. By identifying that the machine has been reconfigured, the technician will have a better opportunity to have the correct parts, tooling, and service information. Identifying that the machine has been reconfigured will also allow Caterpillar to include the retrofitted serial numbers in applicable Service Letters.Safety
Personal injury or death can result from sudden machine movement.Sudden movement of the machine can cause injury to persons on or near the machine.To prevent injury or death, make sure that the area around the machine is clear of personnel and obstructions before operating the machine.
Do not attempt to assemble this machine until you read and you understand the assembly instructions.Improper assembly procedures could result in injury or death.
Personal injury or death can result from improper lifting or blocking.When a hoist or jack is used to lift any part or component, stand clear of the area. Be sure the hoist or jack has the correct capacity to lift a component. Install blocks or stands before performance of any work under a heavy component.Approximate weights of the components are shown. Clean all surfaces where parts are to be installed.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Welding on Electronically Controlled Engines
Proper welding procedures are necessary to avoid damage to electronic controls. Perform welding on the engine according to the following procedure.
Set the engine control to the "STOP" mode.
Turn OFF the fuel supply to the engine.
If equipped, turn the battery disconnect switch to the OFF position. If there is no battery disconnect switch, remove the negative battery cable at the battery.
Protect the wiring harnesses from welding debris and/or from welding spatter.
Do NOT use electrical components (ECM or sensors) or electronic component grounding points for grounding the welder.
Connect the welder ground cable directly to the engine component that will be welded. Place the clamp as close as possible to the w


Parts gear Force:

F90891
 
F90891 GEAR SHIFT ARM PIN
H0060B76A, H0350H78L, H0351H76K, H0352H77H, H0356H75F, H0456B78J, H0555H74G, H0558H79L, H0559B80M, H0559H77H, H0559H77J, H0559H78K, H0659B78B, H0757H75A, H0757H76C, H0757H78D, H0857B78F, H0859H77A, H1057B78H, H1059H76D, H1059H77G, H1157H78A, H1159H77
FA90871-2
 
FA90871-2 GEAR SHIFT ARM PIN W/YOKE
H0060B76A, H0352H77H, H0356H75F
F328621
 
F328621 GEAR SHIFT LEVER ARM
H0352H77H, H0352H79L, H0353H78K, H0353H82P, H0356H75F, H0456B78J, H0503B83A
FC544054
FK1074
 
FK1074 GEAR HOUSING SEAL KIT
H0257F88A, H0257F88B, H0352F90B, H0352F90C, H0352H79L, H0353E91A, H0353E91B, H0353H80M, H0353H81N, H0353H82P, H0356F89B, H0357C88B, H0357F89C, H0357G90A, H0456B79K, H0456B80L, H0457H82N, H0457H83P, H0503H84B, H0504H88C, H0504H88D, H0504P89B, H0505C89
Back to top