F390137 Force GRIP, STEERING HANDLE


F390137 GRIP, STEERING HANDLE Force H0033H75C, H0042081C, H0042082D, H0042083E, H0042B78C, H0042B80G, H0042C84L, H0042C87A, H0042H77B, H0042H78D, H0042H78E, H0042H79F, H0043F85A, H0052C88A, H0064H78D GRIP
F390137 GRIP, STEERING HANDLE Force
Rating:
18

Buy GRIP, STEERING HANDLE F390137 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 31
 

Force entire parts catalog list:

H0033H75C 1975,1977
H0042081C 1981
H0042082D 1982
H0042083E 1983
H0042B78C 1978
H0042B80G 1980
H0042C84L 1984
H0042C87A 1987
H0042H77B 1977
H0042H78D 1978
H0042H78E 1978
H0042H79F 1979
H0043F85A 1985,1986
H0052C88A 1988,1989,1990,1991,1992,1993,1994,1995
H0064H78D 1978

Information:


Illustration 1 g00829434
Schematic
Illustration 2 g01007781
P1 ECM connectorTest Step 1. Inspect Electrical Connectors and Wiring
Turn the keyswitch to the OFF/RESET position.
Thoroughly inspect the J1/P1 ECM connector, the J61/P61 machine connector, the J403/P403 throttle position sensor connector and all other connectors in the circuit. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.Expected Result:All connectors, pins, and sockets are completely inserted and coupled. The harness and wiring are free of corrosion, of abrasion, and of pinch points. All connections and grounds are tight and free of corrosion.Results:
OK - The connectors and the wiring appear to be OK. Proceed to Test Step 2.
Not OK - There is a problem with the connectors and/or the wiring.Repair: Repair the circuit.Verify that the repair eliminates the problem.STOPTest Step 2. Check for Shorts in the Harness from the ECM to the Throttle Position Sensor
Disconnect the J1/P1 ECM connector and the J403/P403 throttle position sensor connector.
Measure the resistance between P1:4 (+8 VDC) and engine ground.
Measure the resistance between P1:4 (+8 VDC) and P1:5 (Return).
Leave the J1/P1 ECM connector and the throttle position sensor disconnected.Expected Result:The resistance is greater than 20,000 Ohms for each measurement.Results:
OK - The resistance is greater than 20,000 Ohms for each measurement. Proceed to Test Step 3.
Not OK - There is a short between the ECM and the sensor.Repair: Repair the circuit.STOPTest Step 3. Check for Open Circuits in the Harness Between the ECM and the Throttle Position SensorNote: The J1/P1 ECM connector and the throttle position sensor should still be disconnected.
Install a jumper wire between P1:4 (+8 VDC) and P1:5 (Return).
Measure the resistance between terminal A (+8 VDC) and terminal B (Return) of the P403 throttle position sensor connector on the wiring harness.Expected Result:The resistance is less than 10 Ohms.Results:
OK - The resistance is less than 10 Ohms.Repair: Remove the jumper wire and reconnect the J1/P1 ECM connector. Leave the throttle position sensor disconnected. Proceed to Test Step 4.
Not OK - There is an open circuit in the wiring harness between the sensor and the ECM.Repair: Repair the circuit.Verify that the repair eliminates the problem.STOPTest Step 4. Check the Digital Sensor Supply Voltage at the Sensor Connector
Turn the keyswitch to the ON position.
Measure the voltage across terminal A (+8 VDC) and terminal B (Return) of the P403 throttle position sensor connector on the wiring harness.Expected Result:The digital sensor supply voltage is 8.0 0.5 VDC.Results:
OK - The supply voltage is reaching the sensor. Proceed to Test Step 5.
Not OK - The supply voltage is not reaching the sensor. Proceed to Test Step 7.Test Step 5. Check the Digital Sensor for an Internal Short
Install a 7X-6370 Adapter Cable As (3 Pin DT Breakout) at the sensor connector, but do not connect the sensor to the breakout at this time.
Turn the keyswitch to the ON position.
Reconnect the throttle position sensor while you observe the voltage across terminals A (+8 VDC) and B (Return) at the breakout.Expected Result:The supply voltage is 8.0 0.5 VDC and the voltage does not drop when the sensor is connected.Results:
OK - The sensor does not have an internal short.Repair: Refer to Troubleshooting, "Electrical Connectors - Inspect" if the problem is intermittent.STOP
Not OK - The sensor may have an internal short. Proceed to Test Step 6.Test Step 6. Temporarily Install a New Sensor
Disconnect the suspect sensor and remove the suspect sensor.
Turn the keyswitch to the ON position.
Temporarily connect a new sensor to the breakout while you observe the voltage across terminals A (+8 VDC) and B (Return) at the breakout.Expected Result:The supply voltage is 8.0 0.5 VDC and the voltage does not drop when the sensor is connected.Results:
OK - The suspect sensor was faulty.Repair: Permanently install the new sensor.STOP
Not OK - The sensor and the circuit appear to be OK at this time.Repair: Refer to Troubleshooting, "Electrical Connectors - Inspect" if the problem is intermittent.STOPTest Step 7. Check the Digital Sensor Supply Voltage at the ECM
Install a 140-2266 Cable (Seventy-Pin Breakout) at the J1/P1 ECM connector.
Turn the keyswitch to the ON position.
Measure the voltage across P1:4 (+8 VDC) and P1:5 (Return) at the breakout.Expected Result:The supply voltage is 8.0 0.5 VDC.Results:
OK - The ECM is supplying the correct voltage.Repair: Refer to Troubleshooting, "Electrical Connectors - Inspect" if the problem is intermittent.STOP
Not OK - The ECM is not supplying the correct voltage.Repair: Verify your results.Replace the ECM. Refer to Troubleshooting, "Replacing the ECM" before replacing the ECM.Verify that the repair eliminates the problem.STOP


Parts grip Force:

F459137
 
F459137 GRIP
H0032H84G, H0064H78D
F702137
 
F702137 GRIP-STEERING HANDLE
H005201RS, H0052C88A, H0091H84D, H009201RS, H009201SD, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H015201RS, H015211SS, H0152C84K, H0152S89A
Back to top