825207A 2 Force HARNESS ASSEMBLY-CDM Tester


825207A 2 HARNESS ASSEMBLY-CDM Tester Force H040312SD, H040312UD, H075312SD, H075312UD, H075412VD, H090412SD, H090412UD, H090422VD, H120412SD, H120412UD HARNESS
825207A 2 HARNESS ASSEMBLY-CDM Tester Force
Rating:
53

Buy HARNESS ASSEMBLY-CDM Tester 825207A 2 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: -
 

Force entire parts catalog list:

H040312SD 1996,1997
H040312UD 1998,1999
H075312SD 1996,1997
H075312UD 1998
H075412VD 1999
H090412SD 1996,1997
H090412UD 1998
H090422VD 1999
H120412SD 1996,1997
H120412UD 1998,1999

Information:

This procedure checks for air in the fuel. This procedure also assists in finding the source of the air.
Examine the fuel system for leaks. Ensure that the fuel line fittings are properly tightened. Check the fuel level in the fuel tank. Air can enter the fuel system on the suction side between the fuel transfer pump and the fuel tank.
Install a 2P-8278 Fuel Flow Tube (Sight Gauge) in the fuel return line. When possible, install the sight gauge in a straight section of the fuel line that is at least 304.8 mm (12 inches) long. Do not install the sight gauge near the following devices that create turbulence:
Elbows
Relief valves
Check valvesObserve the fuel flow during engine cranking. Look for air bubbles in the fuel. If there is no fuel in the sight gauge, prime the fuel system. Refer to Testing and Adjusting, "Fuel System - Prime" for more information. If the engine starts, check for air in the fuel at varying engine speeds. When possible, operate the engine under the conditions which have been suspect of air in the fuel.
Illustration 1 g00578151
2P-8278 Fuel Flow Tube (Sight Gauge) (1) A steady stream of small bubbles with a diameter of approximately 1.60 mm (0.063 inch) is an acceptable amount of air in the fuel. (2) Bubbles with a diameter of approximately 6.35 mm (0.250 inch) are also acceptable if there is two seconds to three seconds intervals between bubbles. (3) Excessive air bubbles in the fuel are not acceptable.
If excessive air is seen in the sight gauge in the fuel return line, install a second sight gauge at the inlet to the fuel transfer pump. If a second sight gauge is not available, move the sight gauge from the fuel return line and install the sight gauge at the inlet to the fuel transfer pump. Observe the fuel flow during engine cranking. Look for air bubbles in the fuel. If the engine starts, check for air in the fuel at varying engine speeds.If excessive air is not seen at the inlet to the fuel transfer pump, the air is entering the system after the fuel transfer pump. Proceed to Step 6.If excessive air is seen at the inlet to the fuel transfer pump, air is entering through the suction side of the fuel system.
To avoid personal injury, always wear eye and face protection when using pressurized air.
To avoid damage, do not use more than 55 kPa (8 psi) to pressurize the fuel tank.
Pressurize the fuel tank to 35 kPa (5 psi). Do not use more than 55 kPa (8 psi) in order to avoid damage to the fuel tank. Check for leaks in the fuel lines between the fuel tank and the fuel transfer pump. Repair any leaks that are found. Check the fuel pressure in order to ensure that the fuel transfer pump is operating properly. For information about checking the fuel pressure, see Testing and Adjusting, "Fuel System Pressure - Test".
If the source of the air is not found, disconnect the supply line from the fuel tank and connect an external fuel supply to the inlet of the fuel transfer pump. If this corrects the problem, repair the fuel tank or the stand pipe in the fuel tank.
If the injector sleeve is worn or damaged, combustion gases may be leaking into the fuel system. Also, if the O-rings on the injector sleeves are worn, missing, or damaged, combustion gases may leak into the fuel system.


Parts harness Force:

819514A 6
 
819514A 6 HARNESS ASSEMBLY
H075312SD, H0903E91H, H1201A90A, H1501E89A
819514A10
 
819514A10 HARNESS ASSEMBLY, TRIM
H040312RD, H040312SD, H040312UD
17201A 7
 
17201A 7 HARNESS ASSEMBLY, TRIM
H040312RD, H040312SD, H040312UD
828296A 1
 
828296A 1 HARNESS ASSEMBLY-Wiring
H040312SD, H040312UD
828298A 1
 
828298A 1 HARNESS ASSEMBLY-Ignition
H075312SD, H075312UD, H075412VD, H090412SD, H090412UD, H090422VD
828297A 1
 
828297A 1 HARNESS ASSEMBLY
H075312SD, H075312UD, H075412VD, H090412SD, H090412UD, H090422VD, H120412SD, H120412UD
819514A11
 
819514A11 HARNESS ASSEMBLY-Wiring
H075312SD, H075312UD, H075412VD, H090412SD, H090412UD, H090422VD, H120412SD, H120412UD
828298A 2
Back to top