FT2948 Force HELI COIL KIT (3/8-16)


FT2948 HELI COIL KIT (3/8-16) Force H005201SD, H005201TS, H005201UD, H0052C88A, H0091H84D, H009201SD, H009201UD, H009201US, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H015201US, H015211SS, H0152C84K, H0152S89A, H040312RD, H040312SD, H040312UD, H0407E92C, H0706A91B, H075312S HELI
FT2948 HELI COIL KIT (3/8-16) Force
Rating:
78

Buy HELI COIL KIT (3/8-16) FT2948 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: -
 

Force entire parts catalog list:

H005201SD 1996,1997
H005201TS 1997
H005201UD 1998,1999
H0052C88A 1988,1989,1990,1991,1992,1993,1994,1995
H0091H84D 1984
H009201SD 1996,1997
H009201UD 1998
H009201US 1998
H0092284D 1984,1985,1986,1987,1988,1989,1990,1991,1992,1993,1994,1995
H0092H84L 1984
H0092S88A 1988
H0092S91A 1991
H0093S91A 1991
H015201US 1998
H015211SS 1996,1997
H0152C84K 1984
H0152S89A 1989
H040312RD 1995
H040312SD 1996,1997
H040312UD 1998,1999
H0407E92C 1992,1993,1994
H0706A91B 1991,1992,1993,1994,1995
H075312SD 1996,1997
H075312UD 1998
H090312RD 1995
H0903E91H 1991,1992,1993,1994
H1201A90A 1990,1991,1992,1993,1994
H120412RD 1995
H1501E89A 1989,1990,1991,1992,1993,1994

Information:


Illustration 1 g02251074
Schematic for the fuel pressure differential pressure switch
Test Step 1. Inspect the Electrical Connectors and the Wiring
Turn the keyswitch to the OFF position.
Illustration 2 g02251713
Left side engine view (typical example)
(1) J2/P2 ECM connectors
Illustration 3 g02251794
Typical location of the fuel filter differential pressure switch (right front engine view)
(2) Fuel filter differential pressure switch
Thoroughly inspect connector (1). Also, thoroughly inspect the connector for switch (2). Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Illustration 4 g02251855
Terminal locations at the P2 ECM connector for the fuel filter differential pressure switch
(P2-49) Fuel filter differential pressure switch
(P2-54) Return
Illustration 5 g01218763
Connector for the fuel filter differential pressure switch
(Terminal 1) Fuel filter differential pressure switch
(Terminal 2) Return for the switch
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector and the sensor connectors.
Check the allen head screw for each of the ECM connectors for the proper torque. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Check the harness and wiring for abrasions and for pinch points from the sensor to the ECM. Expected Result:All connectors, pins, and sockets are coupled and/or inserted. The harness and wiring are free of corrosion, of abrasion, and of pinch points.Results:
OK - The harness and wiring are OK. Proceed to Test Step 2.
Not OK - There is a problem in the connectors and/or wiring.Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are coupled.Verify that the repair eliminates the problem.STOPTest Step 2. Check the Switch Circuit with no Pressure in the Fuel System
Disconnect the connector for the differential pressure switch.
Check continuity between the terminals for the differential pressure switch at the connector. Expected Result:The resistance check indicates a short circuit.Results:
OK - The resistance check indicates a short circuit. Proceed to Test Step 3.
Not OK - The resistance check indicates an open circuit. There is an open circuit in the fuel filter differential pressure switch.Repair: Replace the differential pressure switch.STOPTest Step 3. Check the Switch Circuit with Pressure in the Fuel System
Turn the keyswitch to the ON position.
Use the "Fuel Pump Relay Command Override" in "Caterpillar" Electronic Technician (ET) to engage the fuel priming pump.
While the fuel priming pump is running, check continuity between the terminals for the differential pressure switch at the connector.
Turn the keyswitch to the OFF position. Expected Result:The resistance check indicates a short circuit.Results:
OK - The resistance check indicates a short circuit. The differential pressure switch is OK. Proceed to Test Step 4.
Not OK - The resistance check indicates an open circuit. There is an open circuit in the wiring for the fuel filter differential pressure switch.Repair: Replace the differential pressure switch.STOPTest Step 4. Check for an Open Circuit in the Harness
Disconnect the J2/P2 ECM connector.
Create a short on the ECM side of the harness between the terminals of the connector for the differential pressure switch.
Check continuity at the ECM connector between terminal P2-49 (fuel filter pressure switch) and terminal P2-54 (return). Expected Result:The resistance check indicates a short circuit.Results:
OK - The resistance check indicates a short circuit. Proceed to Test Step 5.
Not OK - The resistance check indicates an open circuit.Repair: Repair the connectors or wiring and/or replace the connectors or wiring between the ECM and the connector for the differential pressure switch.STOPTest Step 5. Check for a Short Circuit in the Harness
Check continuity at the ECM connector between terminal P2-49 (fuel filter pressure switch) and every terminal on the P1 and P2 ECM connectors. Expected Result:The resistance checks indicate an open circuit.Results:
OK - The resistance checks indicate an open circuit.Repair: Check all connectors and wiring. Ensure that there are clean, solid connections at each connector. Return all wiring to the original configuration and retest the circuit. The most likely cause of the problem is a poor connection. The ECM can be tested by removing the wire P2-49 (fuel filter pressure switch) from the P1 ECM connector. Start and run the engine. After an hour, check for an event code related to the switch. If the event code is activated with the open in place at the ECM connector, there may be a problem with the ECM. Before you consider replacing the ECM, consult the Dealer Solutions Network (DSN).STOP
Not OK - The resistance checks indicate a short circuit.Repair: Repair the connectors or wiring and/or replace the connectors or wiring between the ECM and the connector for the differential pressure switch.STOP


Parts heli Force:

FT2969
 
FT2969 HELI COIL KIT (10-24)
H005201SD, H005201TS, H005201UD, H0052C88A, H0091H84D, H009201SD, H009201UD, H009201US, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H015201US, H015211SS, H0152C84K, H0152S89A, H040312RD, H040312SD, H040312UD, H0407E92C, H0706A91B, H075312S
FT2970
 
FT2970 HELI COIL KIT (1/4-20)
H005201SD, H005201TS, H005201UD, H0052C88A, H0091H84D, H009201SD, H009201UD, H009201US, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H015201US, H015211SS, H0152C84K, H0152S89A, H040312RD, H040312SD, H040312UD, H0407E92C, H0706A91B, H075312S
FT2971
 
FT2971 HELI COIL KIT (5/16-18)
H005201SD, H005201TS, H005201UD, H0052C88A, H0091H84D, H009201SD, H009201UD, H009201US, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H015201US, H015211SS, H0152C84K, H0152S89A, H040312RD, H040312SD, H040312UD, H0407E92C, H0706A91B, H075312S
Back to top