F7011 Force ELASTIC STOP NUT, 10 - 24

Table 1
Diagnostic Trouble Codes for the ARD Nozzle Heater    
CDL Code     Description     Notes    
3182-5     Aftertreatment #1 Fuel Injector #1 Heater : Current Below Normal     The Electronic Control Module (ECM) detects the following conditions:
A low current condition (open circuit) in the circuit for the Aftertreatment Regeneration Device (ARD) nozzle heater relay circuit for one second.
The ECM has been powered for at least one second.
The ECM is not attempting to power the ARD nozzle heater relay.    
3182-6     Aftertreatment #1 Fuel Injector #1 Heater : Current Above Normal     The ECM detects the following conditions:
A high current condition (short circuit) in the circuit for the ARD nozzle heater circuit for at least one second.
The ECM has been powered for at least one second.
The ECM is attempting to power the ARD nozzle heater relay.    The ARD nozzle can become plugged with carbon or with debris. The engine is equipped with a system that cleans the nozzle. The ECM periodically tests the condition of the nozzle. The ARD combustion head contains an electric heating element. The heating element operates periodically in order to clean the nozzle.ARD Nozzle Heater TestThe electronic service tool includes the "ARD Nozzle Heater Test". This override will assist the analysis of the ARD nozzle heater circuit. The override can be used to control the operation of the ARD nozzle heater while the engine is not running.
Illustration 1 g02453041
Schematic for the ARD nozzle heater
Illustration 2 g02041053
Pin locations on the P2 connector for the ARD nozzle heater (41) ARD nozzle heater relay return (43) ARD nozzle heater relay control
Illustration 3 g02169813
Pin locations on the 31-pin connector and the 40-pin connector for the ARD nozzle heater circuit
Illustration 4 g02474716
Control panel for the Clean Emissions Module (CEM) (1) 2-pin connector for the ARD nozzle heater (2) Relay for the ARD nozzle heater (3) Connector for the ARD nozzle heater relay (hidden)Test Step 1. Inspect Electrical Connectors And Wiring
Check that the fuses are not blown.
Check the harness for abrasion and pinch points from the ARD nozzle heater back to the ECM. Check the harness for abrasion and pinch points from the ARD nozzle heater back to the battery.
Inspect the connectors for the ARD heater and the ARD heater relay. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Thoroughly inspect the 31-pin connector and the 40-pin connector. Refer to Troubleshooting, "Electrical Connectors - Inspect".
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector and the connectors that are associated with the ARD nozzle heater.
Check the screw for the ECM connector for the correct torque of 6 N m (53 lb in).
Check the harness for abrasions and for pinch points from the heating element back to the ECM.Results:
All connectors, pins, and sockets are correctly coupled and/or inserted. The harness is free of corrosion, abrasion, and pinch points. The fuses are not blown. - Proceed to Test Step 2.
There is a fault with the harness and connectors - Repair: Repair the connectors or the harness and/or replace the connectors or the harness. Ensure that all of the seals are correctly in place and ensure that the connectors are correctly connected. Replace blown fuses.
Start the engine. Wait for the engine to reach operating temperature.
Use the electronic service tool to check for active diagnostic codes.
Do not energize the heater for more than 30 seconds. If the heater is energized more than 30 seconds, damage to the heater can occur. Allow the heating element to cool for 2 minutes between power cycles.
Use the "ARD Nozzle Heater Test" in the electronic service tool to switch on the ARD nozzle heater. Check for active diagnostic codes.
Confirm that the fault has been eliminated.Note: If a fuse is replaced and the fault reoccurs, continue with this procedure.STOPTest Step 2. Check for Active Diagnostic Codes
Connect the electronic service tool to the diagnostic connector.
Start the engine. Wait for the engine to reach operating temperature.
Check for an active 3182-5 diagnostic code.
Do not energize the heater for more than 30 seconds. If the heater is energized more than 30 seconds, damage to the heater can occur. Allow the heating element to cool for 2 minutes between power cycles.
Use the "ARD Nozzle Heater Test" in the electronic service tool to switch on the ARD nozzle heater. Check for an active 3182-6 diagnostic code.
Use the "ARD Nozzle Heater Test" in the electronic service tool to switch off the ARD nozzle heater.Results:
A 3182-5 diagnostic code is active or recently logged. - Proceed to Test Step 3.
A 3182-6 diagnostic code is active or recently logged. - Proceed to Test Step 6.
There are no active 3182 diagnostic codes. - There may be a fault with the switched power circuit for the ARD nozzle heater. The ECM does not monitor the status of this condition. Proceed to Test Step 11.Test Step 3. Create a Short at the ARD Nozzle Heater Relay
Turn the keyswitch to the OFF position.
Disconnect the connector for the ARD nozzle heater relay.
Fabricate a jumper wire that is 150 mm (6 in