F695088 Force HOSE, HYDRAULIC (DOWN)


F695088 HOSE, HYDRAULIC (DOWN) Force H085LD89A, H085LD89B, H085LD89C, H090LD90A, H120LD90A, H125LD89A, H125LD89B HOSE
F695088 HOSE, HYDRAULIC (DOWN) Force
Rating:
63

Buy HOSE, HYDRAULIC (DOWN) F695088 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 3
 

Force entire parts catalog list:

H085LD89A 1989
H085LD89B 1989
H085LD89C 1989
H090LD90A 1990
H120LD90A 1990
H125LD89A 1989
H125LD89B 1989

Information:

1. Remove the bolt and lock that holds suction bell (1) to the oil pan plate. Remove two bolts (4) that hold the elbow to the oil pump.
Oil pump idler gear (2) can fall off the pump when the pump is removed. To prevent injury, always hold the gear on the pump when the pump is removed.
2. Remove the bolts and locks that hold the oil pump to the engine. Remove oil pump (3). The following steps are for the installation of the oil pump.3. Install idler gear (2) on oil pump (3). Put the oil pump in position on the engine as shown with idler gear (2) engaged with the crankshaft gear. Install the bolts and locks that hold the oil pump to the engine.4. Install bolts (4) that hold the elbow to the oil pump.5. Install the bolt and lock that hold suction bell (1) to the oil pan plate.End By:a. install oil panDisassemble Oil Pump
Start By:a. remove oil pump (3304) or remove oil pump (3306) FLUID SPILLAGE CONTAINMENT Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the machine. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to "TOOLS AND SHOP PRODUCT GUIDE, NENG2500", for tools and supplies suitable to collect and contain fluids in Caterpillar machines. Dispose fluids according to local regulations and mandates. 1. Remove idler gear (2). Remove the bearing from the idler gear with Tooling (B).2. Remove suction bell (1).3. Remove the bolt and the washer from the oil pump drive gear. 4. Remove the drive gear from the shaft with Tooling (A).5. Remove the key from the pump shaft.6. Remove bolts (3) from the pump body. 7. Remove body (8), two gears (7), the keys and spacer (4) from the pump.8. Remove two shafts (5) and the gears.9. Remove bolts (6), the cover and the pressure relief valve from the body. 10. Remove the bearings from the oil pump body assembly and the scavenge pump body assembly with Tooling (B).Assemble Oil Pump
1. Install the bearings in the scavenge pump body assembly with Tooling (A) and a press as follows: a. Put bearings (1) in position on the inside of the scavenge pump body assembly with the chamfer on the bearing toward the outside of the pump body. Install the bearing until it is 1.52 mm (.060 in) below the inside machined surface of the scavenge pump body assembly. Make sure the joints in the bearings are at an angle of 30 15 degrees from the center line through the bores in the scavenge pump body and toward the outlet passage of the pump. The outlet passage has a cavity between the bearing bores. 2. Install the bearings in oil pump body assembly with Tooling (A) and a press as follows: a. Put bearings (2) in position on the inside of the oil pump body assembly with the chamfer on the bearings toward the outside of the pump body. Install the bearings until they are even with the outside of the pump body. Make sure the joints in the bearings are at an angle of 30 15 degrees from the centerline through the bearing bores and toward the outlet passage of the pump. The outlet passage has a cavity between the bearing bores.3. Check the condition of the relief valve. Check the condition and specifications for all the parts of the oil pump before it is assembled. See the topic "Oil Pump" in the Specifications Manual.4. Put clean engine oil on all the parts of the oil pump. 5. Install pressure relief valve (3), cover (4) and bolt (5) in the oil pump body assembly. 6. Install shaft assemblies (6) in the oil pump body assembly.7. Install spacer (7). Install the key in the shaft assembly.8. Install the two gears on the shaft assemblies. 8. Install scavenge pump body assembly (8) and the bolts that hold it.9. Install key (9), drive gear (11), the washer and bolt (10). Tighten the bolt to a torque of 43 7 N m (32 5 lb ft).10. Install the bearing in the idler gear with Tooling (A) and a press until it is even with the outside surface of the gear.11. Install the suction bell on the oil pump. Install the idler gear on the oil pump.
The oil pump must turn freely by hand after it is assembled.
End By:a. install oil pump


Parts hose Force:

F433253
 
F433253 HOSE
H0700H79A, H0709B79A, H0750H79A, H0756H80F, H0756H81G, H0756H82H, H0757B79E, H0757H75A, H0757H76C, H0757H78D, H0758H80B, H0758H82E, H0759H79A, H0850H79A, H0850H80A, H0850H81C, H0851H79A, H0851X88A, H0853F88B, H0853F89C, H0853F89E, H0853F89F, H0853F89
FT8900
HOSE CLAMP PLIERS
FT8900 HOSE CLAMP PLIERS
H0032H84G, H0042081C, H0042082D, H0042083E, H0042C84L, H0043F85A, H005201SD, H005201TS, H005201UD, H0052C88A, H0054H76D, H0064H82H, H0071H81B, H0071H82C, H0071H83D, H0071H84E, H0072B81D, H0072H82E, H0091H83C, H0091H84D, H009201SD, H0092284D, H0092H81
F695276-2
 
F695276-2 HOSE, EXHAUST
H085LD89A, H085LD89B, H085LD89C, H090LD90A, H120LD90A, H120LD90B, H125LD89A, H125LD89B
F695261-1
 
F695261-1 HOSE, EXHAUST
H085LD89A, H085LD89B, H085LD89C, H090LD90A, H120LD90A, H120LD90B, H125LD89A, H125LD89B
F695773
 
F695773 HOSE, EXHAUST MANIFOLD & SPACER PLATE
H085LD89A, H085LD89B, H085LD89C, H090LD90A, H120LD90A, H125LD89A, H125LD89B
F695254
 
F695254 HOSE
H085LD89A, H085LD89B, H085LD89C, H090LD90A, H090LD90B, H090LD90C, H090LD91D, H120LD90A, H120LD90B, H120LD90C, H120LD91B, H120LD91D, H120LD92B, H125LD89A, H125LD89B
F695865
 
F695865 HOSE, BOWL VENT
H085LD89A, H085LD89B, H085LD89C, H090LD90A, H090LD90B, H090LD90C, H090LD91D
F695754
 
F695754 HOSE, FUEL DRAIN
H085LD89A, H085LD89B, H085LD89C, H0903E91D, H0903F91A, H0903F91C, H090LD90A, H090LD90B, H090LD90C, H090LD91D, H120LD90A, H120LD90B, H120LD90C, H120LD91B, H120LD91D, H120LD92B, H125LD89A, H125LD89B
Back to top