F17068 Force DETENT SPRING


F17068 DETENT SPRING Force H0356H75F, H0456B78J, H0456B79K, H0456B80L, H0457H82N, H0457H83P, H0507H81A, H0507H82B, H0555H74G, H0558H79L, H0559B80M, H0559H77H, H0559H77J, H0559H78K, H0559H80N, H0659B78B, H0700H79A, H0709B79A, H0750H79A, H0756H80F, H0756H81G, H0756H82H, H0757B79 DETENT
F17068 DETENT SPRING Force
Rating:
103

Buy DETENT SPRING F17068 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 37
 

Force entire parts catalog list:

H0356H75F 1975,1976,1977
H0456B78J 1978
H0456B79K 1979
H0456B80L 1980,1981
H0457H82N 1982
H0457H83P 1983,1984
H0507H81A 1981
H0507H82B 1982
H0555H74G 1974,1976
H0558H79L 1979
H0559B80M 1980
H0559H77H 1977
H0559H77J 1977
H0559H78K 1978
H0559H80N 1980,1981
H0659B78B 1978
H0700H79A 1979
H0709B79A 1979
H0750H79A 1979
H0756H80F 1980
H0756H81G 1981
H0756H82H 1982
H0757B79E 1979
H0757H75A 1975,1976
H0757H76C 1976
H0757H78D 1978
H0758H80B 1980
H0758H82E 1982,1983,1984
H0850H79A 1979
H0850H80A 1980
H0850H81C 1981
H0851H79A 1979
H0856B80H 1980
H0856H82K 1982,1983
H0857B78F 1978
H0857H79G 1979
H0858B80C 1980
H0858B82E 1982
H0858C84H 1984
H0859B79B 1979
H0859H77A 1977
H0859H78A 1978
H1000H79A 1979
H1004H79A 1979
H1006B80B 1980
H1006B81C 1981
H1007H79A 1979
H1008H80A 1980
H1057B78H 1978
H1058H82G 1982
H1059H76D 1976
H1059H77G 1977
H1150H79A 1979
H1151H79A 1979
H1154B79A 1979
H1156H80C 1980
H1156H81D 1981
H1157B79B 1979
H1157H78A 1978
H1158B82E 1982
H1158H80D 1980
H1159H77A 1977
H1159H78B 1978
H1159H79C 1979
H1209H76F 1976,1977
H1258H81A 1981,1982
H1400H79A 1979
H1401H79A 1979
H1406H80C 1980
H1406H81D 1981
H1407B79B 1979
H1407H78A 1978
H1408B80C 1980
H1408H82D 1982
H1409H78A 1978
H1409H79B 1979

Information:


Illustration 1 g00830479
Schematic
Illustration 2 g00956626
P1 ECM connectorTest Step 1. Inspect Electrical Connectors and Wiring
Thoroughly inspect the J1/P1 ECM connector, the battery connections, and the connections to the keyswitch. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector that are associated with the electrical power supply.
Check the ECM connector (allen head screw) for the proper torque of 6.0 N m (55 lb in).
Check the harness and wiring for abrasions and for pinch points from the battery to the ECM. Also, check the harness and wiring for abrasions and for pinch points from the keyswitch to the ECM.Expected Result:All connectors, pins, and sockets are completely coupled and/or inserted. The harness and wiring are free of corrosion, of abrasion, and/or of pinch points.Results:
OK - The connectors and the wiring appear to be OK. Proceed to Test Step 2.
Not OK - There is a problem with the connectors and/or the wiring.Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled.STOPTest Step 2. Check the Battery Voltage at the Batteries
Measure the no-load battery voltage and load test the batteries. Use the 4C-4911 Battery Load Tester. Refer to Special Instruction, SEHS9249, "Use of 4C-4911 Battery Load Tester for 6, 8 and 12 Volt Lead Acid Batteries" and Special Instruction, SEHS7633, "Battery Test Procedure".Expected Result:The battery voltage is OK and the batteries pass the load test.Results:
OK - Proceed to Test Step 3.
Not OK - Repair: Recharge or replace the faulty batteries. Verify that the repair eliminates the problem.STOPTest Step 3. Check the Unswitched Battery Voltage at the ECM
Ensure that the keyswitch is in the OFF position.
Disconnect the J1/P1 ECM connector.
Measure the voltage between all of the +Battery terminals and all of the −Battery terminals in the P1 ECM connector.Expected Result:The measured voltage is a constant voltage that is within 1 VDC of battery voltage.Results:
OK - The ECM is receiving the correct unswitched battery voltage. Proceed to Test Step 4.
Not OK - Repair: If an intermittent condition is suspected, refer to Troubleshooting, "Electrical Connectors - Inspect".Isolate the circuit that is not providing the correct voltage. Repair the circuit. Verify that the repair eliminates the problem.STOPTest Step 4. Check the Keyswitch Voltage at the ECM
Ensure that the J1/P1 ECM connector is disconnected.
Turn the keyswitch to the ON position.
Measure the voltage between P1:70 (Keyswitch (Run)) and P1:63 (−Battery).
Turn the keyswitch to the OFF position and reconnect the J1/P1 ECM connector.Expected Result:The measured voltage is a constant voltage that is within 1 VDC of battery voltage.Results:
OK - The ECM is receiving the correct voltage at this time. Proceed to Test Step 5.
Not OK - Repair: Repair the keyswitch circuit. Verify that the repair eliminates the problem.STOPTest Step 5. Bypass the Machine Wiring
Batteries give off flammable fumes which can explode.To avoid injury or death, do not strike a match, cause a spark, or smoke in the vicinity of a battery.
Do Not connect the bypass harness to the battery until the 20 amp in-line fuse has been removed from the +Battery line. If the fuse is not removed before connection to the battery, a spark may result.
Illustration 3 g00781203
Bypass harnessNote: This bypass harness is only for test applications. This bypass harness may be left only temporarily on the vehicle. The bypass harness can be used in order to determine if the cause of the intermittent problem is interruptions in battery power to the ECM or the keyswitch circuit.
Turn the keyswitch to the OFF position.
Disconnect the J1/P1 ECM connector.
Connect a bypass harness to the J1/P1 ECM connector.
Remove the 20 amp in-line fuse from the positive battery circuit of the bypass harness and connect the alligator clamps directly to the battery posts. Note: This bypass directly connects the circuit for the keyswitch to the ECM. The ECM will remain powered until the positive battery circuit is interrupted. Remove the 20 amp fuse from the in-line fuse holder in order to power down the ECM. Do not connect the bypass to the battery posts without first removing the 20 amp in-line fuse. Do not remove the bypass from the battery posts without first removing the 20 amp in-line fuse.
Connect Cat ET to the service tool connector of the bypass harness and verify that communication is established.
Restore all wiring to the original condition after testing.Expected Result:Installing the bypass eliminates the problem.Note: The status of the keyswitch will always indicate "On" while the bypass harness is installed.Results:
OK - The symptoms disappear when the bypass harness is installed. Also, the symptoms return when the bypass harness is removed. The problem is in the machine wiring that supplies power to the ECM. Repair the wiring that supplies power to the ECM.STOP
Not OK - Repair: Connect the bypass to another battery and verify if the problem is resolved. If the problem is resolved, the problem is with the machine batteries.If the problem still exists, temporarily connect a test ECM. Remove all jumpers and replace all connectors. Recheck the system for active diagnostic codes and repeat the Test Step. If the problem is resolved with the test ECM, reconnect the suspect ECM. If the problem returns with the suspect ECM, replace the ECM.Verify that the repair eliminates the problem.STOP


Parts detent Force:

F17111
 
F17111 DETENT BALL
H0356H75F, H0456B78J, H0456B79K, H0456B80L, H0457H82N, H0457H83P, H0503B83A, H0503H84B, H0507B85A, H0507C86A, H0507C87A, H0507F87B, H0507H81A, H0507H82B, H0555H74G, H0558H79L, H0559B80M, H0559H77H, H0559H77J, H0559H78K, H0559H80N, H0559H83R, H0606H84
F17006
 
F17006 DETENT SPRING
H0356H75F, H0456B78J, H0456B79K, H0456B80L, H0457H82N, H0457H83P, H0503H84B, H0507B85A, H0507C86A, H0507C87A, H0507F87B, H0507H81A, H0507H82B, H0555H74G, H0558H79L, H0559B80M, H0559H77H, H0559H77J, H0559H78K, H0559H80N, H0559H83R, H0606H84A, H0659B78
F17082-1
 
F17082-1 DETENT BALL
H0356H75F, H0456B78J, H0456B79K, H0456B80L, H0457H82N, H0457H83P, H0503B83A, H0503H84B, H0507B85A, H0507C86A, H0507C87A, H0507F87B, H0507H81A, H0507H82B, H0555H74G, H0558H79L, H0559B80M, H0559H77H, H0559H77J, H0559H78K, H0559H80N, H0559H83R, H0606H84
F17008
 
F17008 DETENT SPRING
H1057B78H, H1059H76D, H1059H77G, H1157H78A, H1159H77A, H1159H78B, H1209H76F, H1407H78A, H1409H78A
F17157
 
F17157 DETENT SPRING
H0503B83A, H0503H84B, H0507B85A, H0507C86A, H0507C87A, H0507F87B, H0559H83R, H0606H84A, H0856C87A, H0856F84A, H0856F85A, H0856F86A, H0858C84H, H0906R83D, H1008H83C, H1058V83H, H1158H84G, H1251F84A, H1251F86A, H1251F87A, H1251X85A, H1408H83E
Back to top