F474244 Force INLET WATER LINE


F474244 INLET WATER LINE Force H0558H79L, H0559B80M, H0559H77H, H0559H77J, H0559H78K INLET
F474244 INLET WATER LINE Force
Rating:
18

Buy INLET WATER LINE F474244 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 5
 

Force entire parts catalog list:

H0558H79L 1979
H0559B80M 1980
H0559H77H 1977
H0559H77J 1977
H0559H78K 1978

Information:


Illustration 1 g01161814
Typical example
Test Step 1. Check for Connector Damage
Turn the engine control switch to the OFF/RESET mode. The engine should be off.
Turn the battery disconnect switch to the OFF position.
Thoroughly inspect the ECM connectors J1/P1 and J2/P2. Inspect all of the other connectors. Refer to the diagnostic functional test Troubleshooting, "Inspecting Electrical Connectors" for details.
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector that are associated with the circuit.
Check the ECM connectors (allen head screw) for the proper torque. Refer to Troubleshooting, "Inspecting Electrical Connectors".
Check the harness and the wiring for abrasion and for pinch points. Expected Result:All connectors, pins, and sockets are completely coupled and/or inserted, and the harness and wiring are free of corrosion, of abrasion and of pinch points.Results:
OK - The connectors and wiring are OK. Proceed to Test Step 2.
Not OK - The connectors and/or wiring need repair.Repair: Repair the connectors and/or wiring or replace the connectors and/or wiring.STOPTest Step 2. Check for Electrical Shorts in the Harness
Disconnect the ECM connector and disconnect the generator connector.
Disconnect any module that is connected to the Cat Data Link.
Measure the resistance at the following points. Wiggle the harness during the measurement in order to reveal an intermittent short.
Cat Data Link + to Cat Data Link −
Cat Data Link + to −Battery terminal
Cat Data Link − to −Battery terminal
Cat Data Link + to +Battery terminal
Cat Data Link − to +Battery terminal
Cat Data Link + to engine ground
Cat Data Link − to engine groundExpected Result:The resistance is greater than 20,000 Ohms for each measurement.Results:
OK - The resistance is greater than 20,000 Ohms. Proceed to Test Step 3.
Not OK - The resistance is less than 20,000 Ohms. There is a short in the harness or in the connectors.Repair: Repair the connector and/or wiring or replace the connector and/or wiring.STOPTest Step 3. Check the Resistance through the Harness for an Open Circuit
Turn the engine control to the OFF/RESET mode. The engine should be off.
Turn the battery disconnect switch to the OFF position.
Disconnect the ECM connector and the generator connector.
Disconnect any module that is connected to the Cat Data Link.
Short the wires of the Cat Data Link together. Create the short at P1-9 and P1-8 of the primary ECM connector.
Set an ohmmeter on the 200 ohm scale. Measure the resistance between the terminals of the Cat Data Link + and the Cat Data Link −. Measure the resistance at the connectors for the ECM. Measure the resistance between the terminals of any module that was connected to the Cat Data Link. Wiggle the harness during the measurements in order to reveal an intermittent open condition.
Short the wires of the Cat Data Link together. Create the short at Pin-13 and Pin-14 of the generator connector.
Reconnect all connectors and modules. Expected Result:The resistance is less than five Ohms for each measurement.Results:
OK - The resistance is less than five Ohms for each measurement.Repair: The harness is OK. There could be a problem with a module or with the ECM. Connect the suspect module on another engine. If the problem returns on the other engine, replace the suspect module. Turn the battery disconnect switch to the OFF position. Turn the battery disconnect switch to the ON position. If the diagnostic code is still present, replace the ECM. Refer to the diagnostic procedure Troubleshooting, "Replacing the ECM".STOP
Not OK - The resistance is greater than five Ohms for each measurement.Repair: There is an open circuit or there is excessive resistance in the harness. Repair the connectors and/or wiring or replace the connectors and/or wiring.STOP


Parts inlet Force:

FO10165
 
FO10165 INLET SEAT GASKET
H0033H75C, H005201RS, H0052C88A, H0060B76A, H0062H79M, H0064H78D, H0082H76G, H0082H79K, H0091B80B, H0091H79A, H009201RS, H0092B80G, H0092H79F, H0092H81H, H0095B81G, H0101B78A, H0102H76C, H0102H78E, H0121B79A, H0122H79E, H0125H79E, H0152B78D, H0152H79
FO10790
INLET NEEDLE, SEAT AND GASKET
FO10790 INLET NEEDLE, SEAT AND GASKET
H0033H75C, H0060B76A, H0062H79M, H0064H78D, H0082H76G, H0082H79K, H0091B80B, H0091H79A, H0092B80G, H0092H79F, H0092H81H, H0095B81G, H0101B78A, H0102H76C, H0102H78E, H0121B79A, H0122H79E, H0125H79E, H0152B78D, H0152H79E, H0152H80F, H0152H81G, H0202B80
F475244
 
F475244 INLET WATER LINE
H0558H79L, H0559B80M, H0559H77H, H0559H77J, H0559H78K
Back to top