FA486385 Force INSERT, PLATE SIDE


FA486385 INSERT, PLATE SIDE Force H0352H77H, H0356H75F INSERT
FA486385 INSERT, PLATE SIDE Force
Rating:
18

Buy INSERT, PLATE SIDE FA486385 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 66
 

Compatible models:

Force entire parts catalog list:

H0352H77H 1977,1978
H0356H75F 1975,1976,1977

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1857 Retaining Ring Pliers 1
B 1U-6683 Ring Expander 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g03003219
Ensure that all components are clean and free from wear and damage. If necessary, replace any components that are worn or damaged.
Position the spring for oil control ring (3) into the oil ring groove in piston (4). The central wire must be located inside the end of the spring.
Position the oil control ring with the word "TOP" in the upward position. Use Tooling (B) to install oil control ring (3) over the piston and the spring. Note: Ensure that the central wire is 180 degrees from the ring gap.
Use Tooling (B) to install intermediate compression ring (2) into the second groove in piston (4). The word "TOP" must be upward.
Use Tooling (B) to install top compression ring (1) into the top groove in piston (4). The word "TOP" must be upward.
Position the piston ring gaps at approximately 120 degrees away from each other. Note: A new piston assembly is supplied with new piston rings.
Illustration 2 g03001779
(A) Cut away for piston cooling jet
(9) Upper shell for connecting rod
(X) Identification marks
(Y) Location tag on connecting rod shells
(Z) Location tag in connecting rod for shells (not shown)
(10) Lower shell for connecting rod cap
Use Illustration 2 as an assembly guide.
Illustration 3 g03001216
Lubricate bushing (8) for piston pin (6) in the connecting rod with clean engine oil. Lubricate the bore for the piston pin in piston (4) with clean engine oil.
Install piston pin (6) to piston (4). Note: If the piston pin cannot be installed by hand, heat the piston to a temperature of 45° 5°C (113° 9°F).
Use Tooling (A) in order to install circlips (5) to the piston pin bore in piston (4). Note: Ensure that the circlips are seated in the grooves in the piston.
Install upper bearing shell (9) into connecting rod (7). Ensure that the locating tab for the upper bearing shell is correctly seated in slot in the connecting rod.
Install lower bearing shell (10) into connecting rod cap (11). Ensure that the locating tab for the lower bearing shell is correctly seated in the slot in the connecting rod cap.
Temporarily install connecting rod cap (11) and bolts (12) to connecting rod (7) when the assembly is out of the engine. Ensure that the etched number on connecting rod cap matches the etched number on connecting rod. Ensure the correct orientation of the connecting rod cap. The locating tab for the upper bearing shell and the lower bearing shell should be on the same side. Tighten bolts (12) to a torque of 20 N m (177 lb in).
Repeat Step 1 through Step 13 for the remaining piston and connecting rod assemblies. Note: Fracture split connecting rods should not be left without the connecting rod caps installed.End By:
Install the pistons and the connecting rods. Refer to Disassembly and Assembly, "Piston and Connecting Rods - Install" for the correct procedure.


Parts insert Force:

FA466892
 
FA466892 INSERT, FRONT PLATE
H0356H75F, H0456B78J, H0555H74G
FA466893
 
FA466893 INSERT, FRONT PLATE
H0356H75F, H0456B78J, H0555H74G
FA467892
 
FA467892 INSERT, FRONT PLATE
H0152B78D, H0356H75F, H0456B78J, H0555H74G, H0559H78K, H0659B78B, H0757H75A, H0757H76C, H0757H78D, H0857B78F, H0859H77A, H1057B78H, H1059H77G, H1157H78A, H1159H77A, H1209H76F, H1407H78A
FA467893
 
FA467893 INSERT, FRONT PLATE
H0152B78D, H0356H75F, H0456B78J, H0555H74G, H0559H78K, H0659B78B, H0757H75A, H0757H76C, H0757H78D, H0857B78F, H0859H77A, H1057B78H, H1059H77G, H1157H78A, H1159H77A, H1209H76F, H1407H78A
F485512
 
F485512 INSERT, PLATE
H0352H77H, H0356H75F, H0555H74G, H0559H77H, H0559H77J
F458677
 
F458677 INSERT, CHOKE KNOB
H0033H75C, H0060B76A, H0062H79M, H0064H78D, H0082H76G, H0082H79K, H0091B80B, H0091H79A, H0091H83C, H0091H84D, H0092284D, H0092B80G, H0092H79F, H0092H81H, H0092H81J, H0092H83K, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H0094H81F, H0101B78A, H0102H76
FA463892
A463893
Back to top