7831 Force JET, MAIN FUEL (.058) (2500-5000')


7831 JET, MAIN FUEL (.058) (2500-5000') Force H040312RD, H0407E92C JET
7831 JET, MAIN FUEL (.058) (2500-5000') Force
Rating:
83

Buy JET, MAIN FUEL (.058) (2500-5000') 7831 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 11
 

Compatible models:

Force entire parts catalog list:

H040312RD 1995
H0407E92C 1992,1993,1994

Information:

Starting The Engine
Woodward PSG Governor
1. Perform all pre-start checks outlined previously. In addition, be sure the alternator and alternator belt are properly installed and adjusted.On some installations, low alternator output frequency will operate a relay to stop the starter. The alternator belts on these arrangements must be inspected regularly for proper belt tension and condition. 2. Push the ON-OFF-STOP switch to the ON position. 3. When the engine starts, move the switch to the OFF position. 4. Start the load.5. Regulate the engine speed with the RAISE-LOWER switch to attain the required instrument panel gauge readings. Woodward UG8 Governor
Start the engine as follows:1. Perform all pre-start checks outlined previously.2. Check the oil level in the sight level gauge with the engine stopped. Oil level should be near the top of the sight level gauge. See the LUBRICATION AND MAINTENANCE PROCEDURES. 3. Turn the load limit knob (3) until the indicator is between "5" and "7".4. Turn the synchronizer knob (2) clockwise until the indicator (4) is at "8". If the governor is equipped with an electric motor, operate synchronizer knob (2) by using the RAISE-LOWER switch on the control panel.5. Move the START-STOP switch to the START position; start the engine.6. Run the engine at low idle for 5 minutes.7. Turn the load limit knob (3) to "10".8. Turn synchronizing knob (2) clockwise until the engine runs at full governed speed.9. Turn speed droop knob (1) to obtain proper droop for the operation: a. For single unit operation, set knob (1) at "0".b. For parallel operation: See Parallel Operation Droop Adjustment in the ELECTRIC SET OPERATION instructions. Speed droop knob (1) on the first unit on the line may be set at "0" droop, and the remaining units set between "30" and "70". These settings should provide constant speed or frequency. If constant speed is not required, set droop knob (1) on all units between "30" and "70".10. Apply the load and readjust the synchronizer knob (2) to obtain the desired load division. Load pointer (5) indicates the relative load.Stopping The Engine
1. Remove the load. See ELECTRIC SET OPERATION instructions if equipped with an electric set generator.2. Reduce engine speed to low idle: Push down and hold the RAISE-LOWER switch until the engine low idle speed is reached. When manually operating a UG8 Governor, move the synchronizer knob until the synchronizer indicator points to "8", or the low idle stop is reached.3. While the engine is idling, check the engine oil level. Oil level must be maintained between the ADD and FULL mark on the side of the dipstick marked CHECK WITH ENGINE RUNNING.4. Stop the engine. a. Solenoid Shutoff: Move the ON-OFF-STOP switch to the STOP position. Hold the switch until the engine stops. b. PSG Governor: Move the shutoff lever forward, or hold the lever up, depending upon installation. Hold the lever in this position until the engine stops. c. UG8 Governor: Turn the load limit knob to "0". 5. Fill the day fuel tank. See the LUBRICATION AND MAINTENANCE PROCEDURES.6. Drain the raw water system if below freezing temperatures are expected; see Section G.7. Observe the Service Meter reading. Perform the periodic maintenance as instructed in the LUBRICATION AND MAINTENANCE CHART, Section C.


Parts jet Force:

6030
 
6030 JET-MAIN (.070) (0 - 2500')
H0091H84D, H009201SD, H009201UD, H009201US, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H015201RS, H015201US, H015211SS, H0152C84K, H0152S89A, H0407E92C, H075412VD, H090312RD, H0903E91H, H090412SD, H090412UD, H090422VD, H1501E89A
F10273
 
F10273 JET-THROTTLE (.047)
H0091H84D, H009201SD, H009201UD, H009201US, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H015201RS, H015201US, H015211SS, H0152C84K, H0152S89A, H040312RD, H040312SD, H0407E92C, H0507A90C, H0507A90D, H0507A91A, H0507A91C, H0507A92A, H0507E91
F10286
 
F10286 JET (.052)
H0407E92C, H0706A91B, H120LD90A, H1251A89D, H1251A89E, H125LD89A, H125LD89B
5733
 
5733 JET (.092)-Main Fuel (1500' - 3000')
H040312RD, H040312SD, H040312UD, H0407E92C, H0706A91B, H075312SD, H1201A90A, H120412RD, H120412SD, H1501E89A
6247
 
6247 JET (.090)-Main Fuel (3000' - 4500')
H040312RD, H040312SD, H040312UD, H0407E92C, H0706A91B, H075312SD, H075312UD, H1201A90A, H120412RD, H120412SD, H1501E89A
3796
 
3796 JET (.076)-Main Fuel (1500' - 3000')
H0407E92C, H090312RD, H0903E91H, H090412SD, H1501E89A
3794
 
3794 JET (.074)-Main Fuel (3000' - 4500')
H0407E92C, H075412VD, H090312RD, H0903E91H, H090412SD, H090412UD, H090422VD, H1501E89A
6207
 
6207 JET (.072)-Main Fuel (4500' - 6000')
H0407E92C, H075412VD, H090312RD, H0903E91H, H090412SD, H090412UD, H090422VD, H1501E89A
Back to top