FA481469 Force ENGINE COVER LATCH HANDLE W/SHAFT


FA481469 ENGINE COVER LATCH HANDLE W/SHAFT Force H0152B78D, H0700H79A, H0709B79A, H0750H79A, H0756H80F, H0756H81G, H0756H82H, H0757B79E, H0757H75A, H0757H76C, H0757H78D, H0758H80B, H0758H82E, H0759H79A, H0850H79A, H0850H80A, H0850H81C, H0851H79A, H0855H79A, H0856B80H, H0856F84A, H0856F85A, H0856F86 ENGINE
FA481469 ENGINE COVER LATCH HANDLE W/SHAFT Force
Rating:
103

Buy ENGINE COVER LATCH HANDLE W/SHAFT FA481469 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 12
 

Force entire parts catalog list:

H0152B78D 1978
H0700H79A 1979
H0709B79A 1979
H0750H79A 1979
H0756H80F 1980
H0756H81G 1981
H0756H82H 1982
H0757B79E 1979
H0757H75A 1975,1976
H0757H76C 1976
H0757H78D 1978
H0758H80B 1980
H0758H82E 1982,1983,1984
H0759H79A 1979
H0850H79A 1979
H0850H80A 1980
H0850H81C 1981
H0851H79A 1979
H0855H79A 1979
H0856B80H 1980
H0856F84A 1984
H0856F85A 1985
H0856F86A 1986
H0856H82K 1982,1983
H0857B78F 1978
H0857H79G 1979
H0858B80C 1980
H0858B82E 1982
H0858C84H 1984
H0859B79B 1979
H0859H77A 1977
H0859H78A 1978
H0906R83D 1983,1984
H1000H79A 1979
H1004H79A 1979
H1006B80B 1980
H1006B81C 1981
H1007H79A 1979
H1008H80A 1980
H1008H83C 1983,1984
H1057B78H 1978
H1058H82G 1982
H1058V83H 1983
H1059H76D 1976
H1059H77G 1977
H1150H79A 1979
H1151H79A 1979
H1154B79A 1979
H1155H79A 1979
H1156H80C 1980
H1156H81D 1981
H1157B79B 1979
H1157H78A 1978
H1158B82E 1982
H1158H80D 1980
H1158H84G 1984
H1159H77A 1977
H1159H78B 1978
H1159H79C 1979
H1209H76F 1976,1977
H1251F84A 1984
H1251F86A 1986
H1251X85A 1985
H1258H81A 1981,1982
H1400H79A 1979
H1401H79A 1979
H1405H79A 1979
H1406H80C 1980
H1406H81D 1981
H1407B79B 1979
H1407H78A 1978
H1408B80C 1980
H1408H82D 1982
H1408H83E 1983,1984
H1409H78A 1978
H1409H79B 1979

Information:


Table 1
J1939 Code CDL Code Code Description Comments
4374-5 3118-5 Aftertreatment #1 Diesel Exhaust Fluid Pump Motor Speed : Current Below Normal This code indicates there is problem with the DEF pump or the wiring harness.
4374-6 3118-6 Aftertreatment #1 Diesel Exhaust Fluid Pump Motor Speed : Current Above Normal This code indicates there is problem with the DEF pump or the wiring harness. Note: 372-5260 Test Kit is required for completing this procedure.
Table 2
Associated Codes
SPN/FMI CDL/FMI Code Description
4337-8 3096-8 Aftertreatment #1 DEF Temperature #1 Sensor : Abnormal Frequency, Pulse Width, or Period
Illustration 1 g03185736Complete the procedure in the order in which the steps are listed.
Table 3
Troubleshooting Test Steps Values Results
1. Check for Fault Codes
A. Turn the keyswitch to the ON position.
B. Connect Cat ET.
C. Record the Fault codes.
Codes
Result: An associated code is present.
Refer to appropriate troubleshooting story.
Result: A 3118 or 4374 code is present.
Proceed to Test Step 2.
2. Check for Opens in the Pump Electronic Tank Unit (PETU) Wiring Harness for the DEF Pump Motor Circuit
A. Turn the keyswitch to the "OFF" position. The keyswitch must be OFF for 2 minutes to allow the DEF pump to purge, reset the code, and reset the DCU.
B. Disconnect the PETU wiring harness from the DEF pump and the Diesel Exhaust Fluid Controller (DCU).
C. Connect the 398-5063 Break-out Connector to the DCU connector.
Connect the 398-5056 Break-out Connector to the pump connector.
The connectors must be used to prevent damage to the DCU and pump connectors.
D. Measure the resistance between terminal 9 (PWM +) on the DEF pump connector and terminal 46 (PWM +) on the 86 pin DCU connector.
E. Measure the resistance between terminal 8 (PWM -) on the DEF pump connector and terminal 26 (PWM -) on the 86 pin DCU connector.
F. Measure the resistance between terminal 10 (PWM SIGNAL) on the DEF pump connector and terminal 24 (PWM SIGNAL) on the 86 pin DCU connector.
Open Circuit
Result: There was less than 10 Ohms of resistance on all of the DEF pump motor circuit wires.
Proceed to Test Step 3.
Result: There was more than 10 Ohms of resistance on any one of the DEF pump motor circuit wires.
Repair: There is an open in the harness. Repair the wiring or replace the harness.
Verify that the problem is resolved.
Proceed to Test Step 4.
3. Check for Short Circuits in the PETU Wiring Harness for the DEF Pump Motor Circuit
A. Turn the keyswitch to the "OFF" position. The keyswitch must be OFF for 2 minutes to allow the DEF pump to purge, reset the code, and reset the DCU.
B. Disconnect the PETU wiring harness from the DEF pump and the DCU.
C. Connect the 398-5063 Break-out Connector to the DCU connector.
Connect the 398-5056 Break-out Connector to the pump connector.
The connectors must be used to prevent damage to the DCU and pump connectors.
D. Measure the resistance between terminal 9 (PWM +) on the DEF pump connector and a known good chassis ground.
E. Measure the resistance between terminal 8 (PWM -) on the DEF pump connector and a known good chassis ground.
F. Measure the resistance between terminal 10 (PWM SIGNAL) on the DEF pump connector and a known good chassis ground.
Short Circuit
Result: There was more than 100 K Ohms of resistance between the connector terminal and ground on all of the DEF pump motor circuit wires.
Proceed to Test Step 4.
Result: There was less than 100 K Ohms of resistance between the connector terminal and ground on any one of the DEF pump motor circuit wires.
Repair: There is a short circuit in the harness. Repair the wiring or replace the harness.
Verify that the problem is resolved.
Proceed to Test Step 5.
4. Check for Short Circuits in the PETU Wiring Harness for the DEF Pump Motor Wiring
A. Turn the keyswitch to the "OFF" position. The keyswitch must be OFF for 2 minutes to allow the DEF pump to purge, reset the code, and reset the DCU.
B. Disconnect the PETU wiring harness from the DEF pump and the DCU.
C. Connect the 398-5063 Break-out Connector to the DCU connector.
The 398-5063 Break-out Connector must be used to prevent damage to the DCU connector.
D. Measure the resistance between terminal 46 (PWM +) and all other pins in the 86 pin DCU harness connector.
E. Measure the resistance between terminal 26 (PWM -) and all other pins in the 86 pin DCU harness connector.
F. Measure the resistance between terminal 24 (PWM SIGNAL) and all other pins in the 86 pin DCU harness connector.
Short Circuit
Result: There was more than 100 K Ohms of resistance on all of the DEF pump motor circuit wires.
Repair: A failed DEF pump has been detected. Replace the DEF pump.
Proceed to Test Step 5.
Result: There was less than 100 K Ohms of resistance on any one of the DEF pump motor circuit wires.
Repair: There is a short circuit in the harness. Repair the wiring or replace the harness.
Verify that the problem is resolved.
Proceed to Test Step 5.
5. Perform a DEF Dosing System Verification Test
A. Turn the keyswitch to the "ON" position. Do not start the engine.
B. Connect to the "Diesel Exhaust Fluid Controller #1 ECM" using Cat ET.
C. Perform the "DEF Dosing System Verification Test" .
Diagnostic Codes
Result: The code did not return.
Return the unit to service.


Parts engine Force:

A480944
 
A480944 ENGINE COVER W/RETAINER, SCREWS AND NUTS
H0757H75A, H0757H76C, H0857B78F
FA489944
 
FA489944 ENGINE COVER W/RETAINER, SCREWS AND NUTS
H1059H76D, H1059H77G, H1157H78A, H1209H76F, H1407H78A
3C553944
 
3C553944 ENGINE COVER COMPLETE
H1150H79A, H1151H79A, H1157B79B
F3C615944
 
F3C615944 ENGINE COVER COMPLETE
H0906R83D, H1008H83C, H1058V83H, H1158H84G
F3C854944
 
F3C854944 ENGINE COVER COMPLETE.
H0856F84A, H0858C84H
F3C598944
Back to top