F483510-1 Force LINK, REVERSE LOCK


F483510-1 LINK, REVERSE LOCK Force H0202B80L, H0202B81M, H0202H79K, H0202H82N, H0252B83G, H0252H78C, H0252H78D, H0306B80C, H0307H81D, H0350H78L, H0357C86A, H0357C87A, H0357F88A, H0357H83N LINK
F483510-1 LINK, REVERSE LOCK Force
Rating:
63

Buy LINK, REVERSE LOCK F483510-1 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 24
 

Force entire parts catalog list:

H0202B80L 1980
H0202B81M 1981
H0202H79K 1979
H0202H82N 1982
H0252B83G 1983,1984
H0252H78C 1978
H0252H78D 1978
H0306B80C 1980
H0307H81D 1981
H0350H78L 1978
H0357C86A 1986
H0357C87A 1987
H0357F88A 1988
H0357H83N 1983,1984

Information:

Probable Causes
Diagnostic codes
Fuel supply
Cold mode operation and cold cylinder cutout
Throttle
Air intake and exhaust system
Cylinder performance
Electrical connectors
Injection actuation pressure
Electronic unit injectors
Governor (if applicable)Recommended Actions
Diagnostic Codes
Check for active diagnostic codes on Caterpillar Electronic Technician (ET). Troubleshoot any active codes before continuing with this procedure.Fuel Supply
Visually check the fuel level. Do not rely on the fuel gauge only. If necessary, add fuel. If the engine has been run out of fuel, it will be necessary to purge the air from the fuel system. Refer to Operation and Maintenance Manual for more information.
Ensure that the fuel supply valve (if equipped) is in the full OPEN position.
Check the fuel lines for the following problems: restrictions, collapsed lines, pinched lines and loose connections. If problems are found with the fuel lines, repair the lines and/or replace the lines.
Prime the fuel system if any of the following procedures have been performed:
Replacement of the fuel filters
Service on the low pressure fuel supply circuit
Replacement of unit injectorsNote: A sight glass in the low pressure supply line is helpful in diagnosing air in the fuel. Refer to Systems Operation/Testing and Adjusting.
Check the fuel tank for foreign objects which may block the fuel supply.
Check the fuel filters.
Check the diesel fuel for contamination. Refer to Systems Operation/Testing and Adjusting.
Cold weather adversely affects the characteristics of the fuel. Refer to the Operation and Maintenance Manual for information on improving the characteristics of the fuel during cold weather operation.Cold Mode Operation and Cold Cylinder Cutout
Use Cat ET in order to verify that the engine has exited cold mode. During cold mode, fuel injection timing is modified. When the engine is in cold mode, the cold cylinder cutout strategy may be active. Cold mode cylinder cutouts may cause variations in vibration and available power. This is normal operation.Throttle
There may be a problem with the throttle. Refer to Troubleshooting, "Speed Control - Test".Air Intake and Exhaust System
Check the air filter restriction indicator, if equipped. Clean plugged air filters or replace plugged air filters. Refer to the Operation and Maintenance Manual.
Check the air inlet and exhaust system for restrictions and/or leaks. Refer to Systems Operation/Testing and Adjusting.Cylinder Performance
Check the valve lash and reset the valve lash, if necessary. Refer to Systems Operation/Testing and Adjusting.
Check for correct installation of the unit injector connectors. Check for correct installation of all other applicable connectors. Refer to Troubleshooting, "Electrical Connectors - Inspect".
Perform the "Cylinder Cutout Test" on Cat ET in order to identify any injectors that might be misfiring.
If Cat ET indicates a problem, remove the electronic unit injector from the suspect cylinder. Refer to Disassembly and Assembly.
Possible causes of low compression are shown in the following list:
Faulty piston
Faulty piston rings
Worn cylinder bores
Worn valves
Faulty cylinder head gasket
Damaged cylinder head
Perform all necessary repairs. Ensure that the repairs have eliminated the problem.
If the repair does not eliminate the problem, reinstall the electronic unit injectors that were removed and continue with this test procedure.Injection Actuation Pressure
Check the engine oil level. Engine oil supplies the injection actuation pressure circuit. The engine oil must be kept at the proper level for fuel injection.
If service has recently been performed on the engine, air may be present in the injection actuation pressure circuit. Allow the engine to fully warm up and operate the engine under load in order to purge the air from the injection actuation pressure circuit.
Perform the "Injection Actuation Pressure Test " in Cat ET. Check the injection actuation pressure. If necessary, check the operation of the injection actuation pressure control valve. Refer to Troubleshooting, "Injection Actuation Pressure Control Valve - Test".Electronic Unit Injectors
Perform the "Injector Solenoid Test" on Cat ET in order to determine if all of the injector solenoids are being energized by the ECM.
Perform the "Cylinder Cutout Test" on Cat ET in order to identify any injectors that might be misfiring.
If Cat ET indicates a problem, remove the electronic unit injector from the suspect cylinder and install a new electronic unit injector. Refer to Disassembly and Assembly.
Ensure that the repairs have eliminated the problem. If there is still a problem, refer to Troubleshooting, "Injector Solenoid - Test".Governor (if applicable)
Adjust the parameters for the governor in order to maintain stability.


Parts link Force:

F458445
 
F458445 LINK, MAGNETO CONTROL SHAFT
H0202B80L, H0202B81M, H0202H79K, H0202H82N, H0252B83G, H0252H77B, H0252H78C, H0252H78D, H0254H75A, H0351H76K
F458509
 
F458509 LINK, MAGNETO STATOR
H0202B80L, H0202B81M, H0202H79K, H0202H82N, H0252B83G, H0252H77B, H0252H78C, H0252H78D, H0254H75A, H0257F88A, H0257F88B, H0306B80C, H0307H81D, H0350H78L, H0351H76K, H0352F90B, H0352F90C, H0353E91A, H0353E91B, H0355D89A, H0356F89B, H0357C86A, H0357C87
Back to top