OB3062 Force LITERATURE (NOT SHOWN) 5H130


OB3062 LITERATURE (NOT SHOWN) 5H130 Force H0457H82N, H0457H83P, H0507H81A, H0507H82B, H0559H80N, H0856H82K, H0858B82E, H0858C84H, H1156H81D, H1158B82E, H1258H81A, H1406H81D, H1408H82D LITERATURE
OB3062 LITERATURE (NOT SHOWN) 5H130 Force
Rating:
23

Buy LITERATURE (NOT SHOWN) 5H130 OB3062 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: -
 

Force entire parts catalog list:

H0457H82N 1982
H0457H83P 1983,1984
H0507H81A 1981
H0507H82B 1982
H0559H80N 1980,1981
H0856H82K 1982,1983
H0858B82E 1982
H0858C84H 1984
H1156H81D 1981
H1158B82E 1982
H1258H81A 1981,1982
H1406H81D 1981
H1408H82D 1982

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A - Guide Studs
M8 by 50 mm 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that wiring harness are correctly routed and the cable straps are not over tightened. Over tightening of the cable straps will damage the wiring harness convoluting.
Illustration 1 g02191814
If necessary, follow Step 1a through Step 1d to assembly the engine oil cooler.
Ensure that engine oil cooler matrix (19) is clean, free from damage and restriction. Replace engine oil cooler matrix (19) if damaged or restricted.
Ensure that spacer plate (17) is clean and free from damage. Replace spacer plate (17) if damaged.
Position a new gasket (18) onto spacer plate (17). Install engine oil cooler matrix (19) to the spacer plate.
Install bolts (16) finger tight.
Illustration 2 g02192853
Illustration 3 g03195397
Tightening sequence for an engine oil cooler with a blanking plate or with a low mounted oil filter base
Clean the gasket surfaces of the cylinder block.
Install Tooling (A) into Position (B).
Position a new gasket (15) (not shown) onto Tooling (A).
Install the assembly of engine oil cooler (14) to the cylinder block.
Install bolts (13) to engine oil cooler (14).Note: Ensure that the bolts of different lengths are installed in the correct position. Ensure that any brackets for the tube assemblies are location and correctly orientated.
Tighten bolts (13) and bolts (16) to a torque of 22 N m (195 lb in) in the sequence that is shown in Illustration 3.
Remove Tooling (A).
Illustration 4 g02191813
If the engine has a low mounted oil filter on the left-hand side, install the oil filter base. Refer to Disassembly and Assembly, "Oil Filter Base - Remove and Install" for the correct procedure.If the engine has a right-hand side oil filter, follow Step 9a through Step 9d to install blanking plate (8).
Install bolts (10) to blanking plate (8).
Position a new gasket (9) (not shown) onto blanking plate (8).
Install the assembly of blanking plate (8) to the assembly of the engine oil cooler.
Tighten bolts (10) to a torque of 22 N m (195 lb in).
Position bracket (6) onto engine oil cooler. Install bolt (7). Tighten bolts (7) to a torque of 22 N m (195 lb in).Note: Ensure that locating pin for the bracket is correctly located into the engine oil cooler.
Install bolt (1) to fuel injection line clamp (2). Tighten bolts (1) to a torque of 10 N m (88 lb in).
Install new cable straps (3) to the engine wiring harness assembly.
Install the breather outlet pipe (4) to crankcase breather canister (5) and all its assembly clips. Refer to Disassembly and Assembly, "Crankcase Breather- Remove" for the correct procedure.
Install oil drain pipe (12) to crankcase breather canister (5) and crankcase breather valve (11). Refer to Disassembly and Assembly, "Crankcase Breather- Remove" for the correct procedure.
Fill the cooling system to the correct level. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct procedure.
Check the level of the engine lubricating oil. Refer to Operation and Maintenance Manual, "Engine Oil Level - Check" for the correct procedure.End By:
Install the mounting bracket for the Electronic Control Module (ECM) . Refer to Disassembly and Assembly, "ECM Mounting Bracket- Remove and Install" for the correct procedure.


Parts literature Force:

Back to top