35048 Force LOCKWASHER (.375)


35048 LOCKWASHER (.375) Force H0706A91B, H090312RD, H0903E91H, H1201A90A, H1501E89A LOCKWASHER
35048 LOCKWASHER (.375) Force
Rating:
13

Buy LOCKWASHER (.375) 35048 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 40
 

Force entire parts catalog list:

H0706A91B 1991,1992,1993,1994,1995
H090312RD 1995
H0903E91H 1991,1992,1993,1994
H1201A90A 1990,1991,1992,1993,1994
H1501E89A 1989,1990,1991,1992,1993,1994

Information:

1. Remove the bolts, clamps and service meter (1) from the accessory drive housing. 2. Remove the bolts, stop (3), spacer (2) and the gasket from the accessory drive housing. 3. Install stop (3) without the spacer and the gasket and install two 5/16"-18 NC bolts. 4. Remove bolt (5) and disconnect linkage (4) from the lever on the governor housing. 5. Remove felt washer (6) from the fuel injection pump. 6. Use tooling (A) and remove the bushing from the fuel injection pump. 7. Remove seal (7) from the fuel injection pump. 8. Move lever (9) forward to move the rack to the center position and use tool (B) and remove fuel injection pump (8) from the fuel injection pump housing.Install Fuel Injection Pumps
The fuel rack must be in the center position before the correct installation of an injection pump is possible.
1. Put the groove of barrel (2) in alignment with the slot of the gear segment (the slot is on the opposite side of the gear segment teeth).2. Move lever (3) forward to move the rack to the center position.3. Look inside the bore of the injection pump housing to find the dowel. Put groove of the barrel in alignment with the dowel and put the injection pump straight down into the bore.4. Use tool (A) and install fuel injection pump (1) in the fuel injection pump housing. 5. Inspect for wear or damage and make a replacement if necessary of seal (4).6. Put seal (4) in position on the fuel injection pump. 7. Install bushing (5) that holds the fuel injection pump in the fuel injection housing. If the fuel injection pump is in the correct position, bushing (5) will turn into the fuel injection housing by hand until the top of the bushing is even with the fuel pump housing.8. Use tool (B) and tighten bushing (5) to a torque of 200 13 N m (150 10 lb.ft.). 9. Put felt washer (6) in position on the fuel injection pump.10. After each pump has been installed, check total rack travel to make sure each pump has been installed correctly. See TESTING AND ADJUSTING. 11. Connect linkage (7) to the lever on the governor housing. 12. Remove stop (8) from the accessory drive housing. 13. Install spacer (9), the gasket and stop (8) on the accessory drive housing. 14. Install service meter (10), the clamps and the bolts on the accessory drive housing.END BY:a) install fuel linesDisassemble Fuel Injection Pumps
START BY:a) remove fuel injection pumps
Be careful when the injection pumps are disassembled. Do not damage the surfaces of the plungers, barrels and bonnets. Any scratches will cause leakage inside the fuel injection pump. The plunger and barrel for each pump are made as a set. Do not put the plunger of one pump in the barrel of another pump. If one part has wear, install a complete new pump assembly. Be careful when the plunger is put into the bore of the barrel.
1. Pull plunger (7), washer (6) and spring (5) out of barrel (4).2. Remove washer (6) from plunger (7).
Do not remove the gear from the plunger. The gear and plunger are assembled and adjusted at the factory.
3. Remove ring (3) and make a separation of barrel (4) from bonnet (1).4. Remove check valve (9), seat (8) and spring (2) from bonnet (1). If the check valve assembly is disassembled, do not mix the parts with parts from another check assembly.Assemble Fuel Injection Pumps
Put clean fuel oil on all parts during assembly.
1. Put spring (7), seat (9) and check valve (5) into position in bonnet (8).2. Install bonnet (8) on barrel (4) and install ring (6) to hold them together. Do not slide bonnet (8) across barrel (4) because the check valve assembly in the bonnet can cause damage to the face of barrel (4).3. Install spring (3) on barrel (4).4. Install washer (2) on plunger (1) with the flat side toward the gear on the plunger.5. Install plunger (1) in barrel (4) until washer (2) is engaged in the spring.END BY:a) install fuel injection pumps


Parts lockwasher Force:

FO992
 
FO992 LOCKWASHER
H1000H79A, H1004H79A, H1006B80B, H1006B81C, H1007H79A, H1008H80A, H1057B78H, H1058H82G, H1059H76D, H1059H77G, H1150H79A, H1151H79A, H1154B79A, H1155H79A, H1156H80C, H1156H81D, H1157B79B, H1157H78A, H1158B82E, H1158H80D, H1159H77A, H1159H78B, H1159H79
FO16620
 
FO16620 LOCKWASHER KIT
H0202B81M, H0202H82N, H0252B83G, H0257F88A, H0257F88B, H0306B80C, H0307H81D, H0352F90B, H0352F90C, H0353E91A, H0353E91B, H0355D89A, H0356F89B, H0357C87A, H0357C88B, H0357F88A, H0357F89C, H0357G90A, H040312RD, H040312SD, H040312UD, H0407E92C, H0504H88
26992
 
26992 LOCKWASHER (1/4") (15)
H005201RS, H005201SD, H005201TS, H005201UD, H0052C88A, H0091H84D, H009201RS, H009201SD, H009201UD, H009201US, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H015201RS, H015201US, H015211SS, H0152C84K, H0152S89A, H025201RD, H025201TD, H025201T
26996
 
26996 LOCKWASHER (#10)
H005201RS, H005201SD, H005201TS, H005201UD, H0052C88A, H0091H84D, H009201RS, H009201SD, H009201UD, H009201US, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H015201RS, H015201US, H015211SS, H0152C84K, H0152S89A, H025201US, H040312RD, H040312S
78968
 
78968 LOCKWASHER (1/4" INTERNAL)
H0091H84D, H009201RS, H009201SD, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H015201RS, H015211SS, H0152C84K, H0152S89A, H025201TD, H025201TS, H025201US, H040312RD, H0407E92C, H0706A91B, H090312RD, H0903E91H, H1201A90A, H120412RD, H1501E89
53166
 
53166 LOCKWASHER (.312)
H040312RD, H040312SD, H040312UD, H0407E92C, H0706A91B, H075312SD, H075312UD, H075412VD, H090312RD, H0903E91H, H090412SD, H090412UD, H090422VD, H1201A90A, H120412RD, H120412SD, H120412UD, H1501E89A
58643
 
58643 LOCKWASHER (.375)
H0407E92C, H0706A91B, H075312SD, H0903E91H, H1201A90A, H120LD92B, H1501E89A
38829
 
38829 LOCKWASHER (.500)
H1201A90A, H1501E89A
Back to top