38829 LOCKWASHER (.500) Force
H1201A90A, H1501E89A
LOCKWASHER
Price: query
Rating:
Force entire parts catalog list:
- DRIVESHAFT HOUSING » 38829
- DRIVESHAFT HOUSING » 38829
Information:
1. Remove fuel lines (1) from the engine. 2. Disconnect tube assembly (3) and wires (2) from the governor. 3. Remove the bolts, the clamps and service meter (4) from the accessory drive housing. 4. Remove bolts (5) that hold the fuel injection pump housing to the accessory drive housing. 5. Fasten strap (7) and a hoist to fuel injection pump housing and governor (6).6. Remove bolts (8) and fuel injection pump housing and governor (6) from the engine. The weight of the fuel injection pump housing and governor is 39 kg (87 lb.). 7. If necessary remove seals (9) from the fuel injection pump housing.Install Fuel Injection Pump Housing And Governor
1. Use tool (A) and put engine at top center compression stroke. See TESTING AND ADJUSTING. 2. Remove nuts (1) and cover (2) from the automatic timing advance. 3. Loosen four bolts (2) that hold the automatic timing advance to the drive shaft for the fuel injection pump. 4. Remove plug (3) from the fuel injection pump housing. 5. Time the fuel injection pump by turning the camshaft until the notch in the camshaft is in alignment with the hole in the fuel injection pump housing. Install tool (B) through the housing and into the notch of the camshaft. 6. Inspect for wear or damage and make a replacement if necessary of seals (4).7. Put seals (4) in position on the fuel pump housing. 8. Fasten strap (6) and a hoist to fuel injection pump housing and governor (5).9. Install gasket (7) and fuel injection pump housing and governor (5) on the accessory drive housing and engine block with the bolts that hold it. 10. Tighten bolts (8) of automatic timing advance (9) in the following sequence.a) Tighten bolts (8) evenly to a torque of 35 N m (25 lb.ft.).b) Tighten bolts (8) evenly to a torque of 70 N m (50 lb.ft.).c) Tighten bolts (8) evenly to a final torque of 135 7 N m (100 5 lb.ft.). 11. To check for correct engine timing follow the steps below.a) Remove tool (B) from the fuel pump housing and the bolt from the flywheel.b) Turn the flywheel counterclockwise (as seen from the front of the engine) two complete revolutions.c) If the engine is in correct timing, tool (B) can be installed in the notch of the camshaft in the fuel injection pump housing and the bolt can be installed in the flywheel.d) If tool (B) and the bolt can not be correctly installed, the timing is not correct and Step 11 must be repeated. The flywheel can be out of alignment 1° and still be in correct timing. 12. Remove tool (B) and install plug (10) in the fuel injection pump housing.13. Install service meter (11) on the accessory drive housing with the clamps and bolts. 14. Install gasket (13) and cover (12) to the front cover. 15. Connect tube assembly (14) and wires (15) to the governor. 16. Install fuel lines (16) to the block and fuel injection pump housing.END BY:a) install fuel lines
1. Use tool (A) and put engine at top center compression stroke. See TESTING AND ADJUSTING. 2. Remove nuts (1) and cover (2) from the automatic timing advance. 3. Loosen four bolts (2) that hold the automatic timing advance to the drive shaft for the fuel injection pump. 4. Remove plug (3) from the fuel injection pump housing. 5. Time the fuel injection pump by turning the camshaft until the notch in the camshaft is in alignment with the hole in the fuel injection pump housing. Install tool (B) through the housing and into the notch of the camshaft. 6. Inspect for wear or damage and make a replacement if necessary of seals (4).7. Put seals (4) in position on the fuel pump housing. 8. Fasten strap (6) and a hoist to fuel injection pump housing and governor (5).9. Install gasket (7) and fuel injection pump housing and governor (5) on the accessory drive housing and engine block with the bolts that hold it. 10. Tighten bolts (8) of automatic timing advance (9) in the following sequence.a) Tighten bolts (8) evenly to a torque of 35 N m (25 lb.ft.).b) Tighten bolts (8) evenly to a torque of 70 N m (50 lb.ft.).c) Tighten bolts (8) evenly to a final torque of 135 7 N m (100 5 lb.ft.). 11. To check for correct engine timing follow the steps below.a) Remove tool (B) from the fuel pump housing and the bolt from the flywheel.b) Turn the flywheel counterclockwise (as seen from the front of the engine) two complete revolutions.c) If the engine is in correct timing, tool (B) can be installed in the notch of the camshaft in the fuel injection pump housing and the bolt can be installed in the flywheel.d) If tool (B) and the bolt can not be correctly installed, the timing is not correct and Step 11 must be repeated. The flywheel can be out of alignment 1° and still be in correct timing. 12. Remove tool (B) and install plug (10) in the fuel injection pump housing.13. Install service meter (11) on the accessory drive housing with the clamps and bolts. 14. Install gasket (13) and cover (12) to the front cover. 15. Connect tube assembly (14) and wires (15) to the governor. 16. Install fuel lines (16) to the block and fuel injection pump housing.END BY:a) install fuel lines
Parts lockwasher Force:
FO992
FO992 LOCKWASHER
H1000H79A, H1004H79A, H1006B80B, H1006B81C, H1007H79A, H1008H80A, H1057B78H, H1058H82G, H1059H76D, H1059H77G, H1150H79A, H1151H79A, H1154B79A, H1155H79A, H1156H80C, H1156H81D, H1157B79B, H1157H78A, H1158B82E, H1158H80D, H1159H77A, H1159H78B, H1159H79
FO16620
FO16620 LOCKWASHER KIT
H0202B81M, H0202H82N, H0252B83G, H0257F88A, H0257F88B, H0306B80C, H0307H81D, H0352F90B, H0352F90C, H0353E91A, H0353E91B, H0355D89A, H0356F89B, H0357C87A, H0357C88B, H0357F88A, H0357F89C, H0357G90A, H040312RD, H040312SD, H040312UD, H0407E92C, H0504H88
26992
26992 LOCKWASHER (1/4") (15)
H005201RS, H005201SD, H005201TS, H005201UD, H0052C88A, H0091H84D, H009201RS, H009201SD, H009201UD, H009201US, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H015201RS, H015201US, H015211SS, H0152C84K, H0152S89A, H025201RD, H025201TD, H025201T
26996
26996 LOCKWASHER (#10)
H005201RS, H005201SD, H005201TS, H005201UD, H0052C88A, H0091H84D, H009201RS, H009201SD, H009201UD, H009201US, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H015201RS, H015201US, H015211SS, H0152C84K, H0152S89A, H025201US, H040312RD, H040312S
78968
78968 LOCKWASHER (1/4" INTERNAL)
H0091H84D, H009201RS, H009201SD, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H015201RS, H015211SS, H0152C84K, H0152S89A, H025201TD, H025201TS, H025201US, H040312RD, H0407E92C, H0706A91B, H090312RD, H0903E91H, H1201A90A, H120412RD, H1501E89
53166
53166 LOCKWASHER (.312)
H040312RD, H040312SD, H040312UD, H0407E92C, H0706A91B, H075312SD, H075312UD, H075412VD, H090312RD, H0903E91H, H090412SD, H090412UD, H090422VD, H1201A90A, H120412RD, H120412SD, H120412UD, H1501E89A
58643
35048