F217002 Force MAGNETO BREAKER CAM


F217002 MAGNETO BREAKER CAM Force H0064H82H, H0091H84D, H0092284D, H0092B80G, H0092H79F, H0092H81H, H0092H81J, H0092H83K, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H0094H81F, H0102H76C, H0102H78E, H0122H79E, H0152B78D, H0152B83J, H0152C84K, H0152H79E, H0152H80F, H0152H81G, H0152S89 MAGNETO
F217002 MAGNETO BREAKER CAM Force
Rating:
23

Buy MAGNETO BREAKER CAM F217002 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 11
 

Force entire parts catalog list:

H0064H82H 1982
H0091H84D 1984
H0092284D 1984,1985,1986,1987,1988,1989,1990,1991,1992,1993,1994,1995
H0092B80G 1980
H0092H79F 1979
H0092H81H 1981
H0092H81J 1981,1982
H0092H83K 1983
H0092H84L 1984
H0092S88A 1988
H0092S91A 1991
H0093S91A 1991
H0094H81F 1981,1982
H0102H76C 1976,1977
H0102H78E 1978
H0122H79E 1979
H0152B78D 1978
H0152B83J 1983,1984
H0152C84K 1984
H0152H79E 1979
H0152H80F 1980
H0152H81G 1981
H0152S89A 1989

Information:


Illustration 1 g01209492
Schematic
Illustration 2 g01209500
P1 ECM connector (P1-5) Return (P1-22) High throttle input (P1-23) Low throttle inputTest Step 1. Inspect Electrical Connectors and Wiring
Remove the electrical power from the ECM.
Thoroughly inspect the J1/P1 ECM connector. Refer to diagnostic functional tests Troubleshooting, "Electrical Connectors - Inspect" for details.
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector and the sensor connectors that are associated with the active diagnostic code.
Check the ECM connector (allen head screw) for the proper torque. Refer to diagnostic functional tests Troubleshooting, "Electrical Connectors - Inspect" for details.
Check the harness and wiring for corrosion, for abrasion, and for pinch points from the throttle switch to the ECM.Expected Result:All connectors, pins, and sockets are completely coupled and/or inserted. The harness and wiring are free of corrosion, of abrasion, and of pinch points.Results:
OK - The harness and wiring are OK. Proceed to Test Step 2.
Not OK - There is a problem in the connectors and/or wiring.Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled.Verify that the repair eliminates the problem.STOPTest Step 2. Check the Status of the Throttle Inputs
Connect the Caterpillar Electronic Technician (ET) to the service tool connector.
Restore the electrical power to the ECM.
Observe the status of the throttle inputs on Cat ET while you operate the throttle switch in each position.
Table 1
Throttle Input    Neutral    High "Rabbit"    Low "Tortoise"    
"#1 (Low)"     Off     Off     On    
"#2 (High)"     Off     On     Off    Expected Result:The status of the throttle switch corresponds with the table above.Results:
OK - The throttle switch is functioning properly at this time.Repair: Refer to diagnostic functional tests Troubleshooting, "Electrical Connectors - Inspect" if the problem is intermittent.STOP
Not OK - One or more of the inputs is incorrect. Proceed to Test Step 3.Test Step 3. Check the Harness between the Throttle Switch and the ECM
Remove the electrical power from the ECM.
Disconnect the wires for the suspect throttle input(s) from the throttle switch.
Restore the electrical power to the ECM.
Check the status of the suspect throttle inputs(s) on Cat ET. Refer to Table 1.
Use a jumper wire to short the wires for the suspect throttle input(s) to wire A287-BK.
Monitor the status of the suspect throttle input(s) on Cat ET.
Remove the jumper wire. Reconnect all wires to the original configuration.Expected Result:The status of the suspect throttle input(s) change when the jumper wire is connected.Results:
OK - The harness and the ECM are OK.Repair: Replace the throttle switch.Verify that the repair eliminates the problem.STOP
Not OK - The status of the suspect throttle input(s) do not change when the jumper wire is installed. Verify that the wire A287-BK to chassis ground is not open and that the wire has a good connection to chassis ground. Proceed to Test Step 4.Test Step 4. Check the Operation of the ECM
Remove the electrical power from the ECM.
Remove the wires for the suspect throttle input(s) from ECM connector P1.
Install a 208-0059 Adapter Cable As (70-Pin Breakout) at the J1/P1 ECM connector.
Restore the electrical power to the ECM.
Check the status of the suspect throttle input(s) on Cat ET.
Use a jumper wire to short the terminal(s) for the suspect throttle input(s) between the breakout T and engine ground.
Monitor the status of the suspect throttle input(s) on Cat ET.
Remove the jumper wire and breakout T. Reconnect all wires and connectors to the original configuration.Expected Result:The status of the suspect throttle input changes when the jumper wire is connected.Results:
OK - There is either an open circuit or a short circuit in the wiring between the ECM and the throttle switch.Repair: Repair the circuit.Verify that the repair eliminates the problem.STOP
Not OK - The ECM is not responding to the switch inputs.Repair: Verify your results. Refer to electronic troubleshooting Troubleshooting, "Replacing the ECM" before you replace the ECM.STOP


Parts magneto Force:

F73082
 
F73082 MAGNETO STATOR RING
H0060B76A, H0062H79M, H0064H78D, H0082H76G, H0082H79K, H0091B80B, H0091H79A, H0091H83C, H0091H84D, H0092284D, H0092B80G, H0092H79F, H0092H81H, H0092H81J, H0092H83K, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H0094H81F, H0095B81G, H0095H82H, H0101B78
F431838
 
F431838 MAGNETO CONTROL SHAFT
H0091B80B, H0091H79A, H0091H83C, H0091H84D, H0092284D, H0092B80G, H0092H79F, H0092H81H, H0092H81J, H0092H83K, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H0094H81F, H0101B78A, H0102H76C, H0102H78E, H0121B79A, H0122H79E, H0152B78D, H0152B83J, H0152C84
Back to top