FA715167 Force MANIFOLD KIT (15) (90C/92B & SER.# E000001-E127699)


FA715167 MANIFOLD KIT (15) (90C/92B & SER.# E000001-E127699) Force H0091H84D, H009201SD, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H015201RS, H015211SS, H0152C84K, H0152S89A MANIFOLD
FA715167 MANIFOLD KIT (15) (90C/92B & SER.# E000001-E127699) Force
Rating:
88

Buy MANIFOLD KIT (15) (90C/92B & SER.# E000001-E127699) FA715167 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 8
 

Force entire parts catalog list:

H0091H84D 1984
H009201SD 1996,1997
H0092284D 1984,1985,1986,1987,1988,1989,1990,1991,1992,1993,1994,1995
H0092H84L 1984
H0092S88A 1988
H0092S91A 1991
H0093S91A 1991
H015201RS 1995
H015211SS 1996,1997
H0152C84K 1984
H0152S89A 1989

Information:


Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     4C-5598     Anti-Seize Compound     -    
B     195-4609     Seal Pick     1    
C     -     Isopropyl Alcohol     -    
D     5P-4996     Plug     2    
Fuel leaked or spilled onto hot surfaces or electrical components can cause a fire. To help prevent possible injury, turn the start switch off when changing fuel filters or water separator elements. Clean up fuel spills immediately.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool.
Open the right side engine door.
Illustration 1 g02174349
Disconnect harness assemblies (1) , (2) , and (5) .
Disconnect tube assemblies (3) . Plug the coolant lines with Tooling (D) .
Remove flame detection temperature sensor (6) .
Remove bolts (4) and position the elbow out of the way.
Illustration 2 g02174351
Remove nuts (11) and remove combustion head (10) .
Remove gasket (9) , tube assembly (8) , and gasket (7) .
If required, remove studs (12) .
Illustration 3 g02174350
Remove fittings (13) and (14) .
Remove spark plug (15) and remove filter (16) .
Illustration 4 g02483739
Use Tooling (B) in order to remove O-ring seals (17) and (18) from harness assembly (5) . Discard O-ring seals (17) and (18) .Installation Procedure
Install combustion head (10) in reverse order.
Apply Tooling (A) onto the threads of studs (12) . Install the studs. Tighten studs (12) to a torque of 17 2 N m (150 18 lb in).
Apply Tooling (A) onto the threads of the studs and nuts (11) .
Illustration 5 g02174426
Using the torque sequence illustrated in Illustration 5 to tighten nuts (11) to a torque of 23 3 N m (204 27 lb in). Tighten nuts (11) again using the torque sequence illustrated in Illustration 5 to a torque of 28 3 N m (21 2 lb ft). Tighten nuts (11) again using the torque sequence illustrated in Illustration 5 to a torque of 28 3 N m (21 2 lb ft).
Use caution when you are using isopropyl alcohol. Avoid prolonged skin contact with isopropyl alcohol.Vapors may be harmful if inhaled. Use only in a well ventilated area. Do not smoke while using isopropyl alcohol.Isopropyl alcohol is flammable. Do not use near an open flame or near welding operations. Keep isopropyl alcohol away from heated surfaces exceeding 482°C (900°F).
Note: This connection is an electrical connection and cannot be lubricated with a petroleum-based lubricant. Isopropyl alcohol is the only approved lubrication for this connection.
Lubricate new O-ring seals (17) and (18) with Tooling (C) prior to installation.
Tighten filter (16) to a torque of 60 6 N m (44 4 lb ft).
Tighten fittings (14) and (13) to a torque of 30 2 N m (22 1 lb ft).
Tighten spark plug (15) to a torque of 47 4 N m (35 3 lb ft).
Apply Tooling (A) to the threads of flame detection temperature sensor (6) and install the sensor. Tighten flame detection temperature sensor (6) to a torque of 45 5 N m (33 3 lb ft).
Install a new gasket before installing bolts (4) .
Check the coolant level. If necessary, refer to Operation and Maintenance Manual, "Coolant - Change" for the proper filling procedures.
Perform the ARD ignition test. Refer to Troubleshooting Manual, "ARD Ignition - Test".


Parts manifold Force:

F2A424167
 
F2A424167 MANIFOLD W/STUDS AND PULLEY
H0091B80B, H0091H79A, H0091H83C, H0091H84D, H0092B80G, H0092H79F, H0092H81H, H0092H81J, H0092H83K, H0092H84L, H0094H81F, H0095B81G, H0095H82H, H0101B78A, H0102H76C, H0102H78E, H0121B79A, H0122H79E, H0125H79E, H0152B78D, H0152B83J, H0152C84K, H0152H79
FA424167
 
FA424167 MANIFOLD KIT
H0091H84D, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H0152C84K, H0152S89A
FA714167
 
FA714167 MANIFOLD KIT (9.9) (91C/92B & SER.#E000001-E127699)
H0091H84D, H009201RS, H009201SD, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H015211SS, H0152C84K, H0152S89A
A714167
 
A714167 MANIFOLD W/STUDS
H0092S91A, H0093S91A
Back to top