FZ718366 Force MEDALLION (Gold US MARINE)


FZ718366 MEDALLION (Gold US MARINE) Force H0407E92C, H0507A91A, H0507A91C, H0507A92A, H0507E91B, H0706A91B, H0903E91D, H0903E91H, H0903F91A, H0903F91C, H1201A90A, H1501E89A MEDALLION
FZ718366 MEDALLION (Gold US MARINE) Force
Rating:
53

Buy MEDALLION (Gold US MARINE) FZ718366 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: --
 

Force entire parts catalog list:

H0407E92C 1992,1993,1994
H0507A91A 1991
H0507A91C 1991
H0507A92A 1992
H0507E91B 1991
H0706A91B 1991,1992,1993,1994,1995
H0903E91D 1991
H0903E91H 1991,1992,1993,1994
H0903F91A 1991
H0903F91C 1991
H1201A90A 1990,1991,1992,1993,1994
H1501E89A 1989,1990,1991,1992,1993,1994

Information:

1. Disconnect plug P7 from receptacle J7. The locking ring helps identify P7 from J7. Check the connections for damaged wires or pins and corrosion. Also check that the pins are at the proper height in the connector. Check that the wires and pins are tight in the connectors by pulling (slightly) on each wire of each connector (including the breakout "T").2. Install the 8T8695 Adapter (nine pin breakout "T") between J7 and P7. Twist the locking rings to secure the connections.3. Connect the voltmeter as shown. Check for the appropriate voltages between the lettered "T" pins as explained in Steps 4 through 11.4. Pin B (parking brake) to A (ground):* Less than .5 volts DC with the key on and parking brake applied.* More than 4.5 volts DC with the key on and parking brake released. Diagnosis - Disconnect breakout "T" and check the individual switch circuits for open, ground or faulty switch. Switch circuit must have less than 2.5 ohms resistance and more than 5000 ohms resistance to chassis ground.5. Pin C (brake switch) to A:* Less than .5 volts DC with the key on.* More than 4.5 volts DC with brake pedal applied and the key on. Diagnosis - Disconnect breakout "T" and check the individual switch circuits for open, ground or faulty switch. Switch circuit must have less than 2.5 ohms resistance and more than 5000 ohms resistance to chassis ground.
Vehicle Speed Buffer (1) Magnetic Pickup (2) in transmission. Step 6 checks the proper functioning of the truck wiring, vehicle speed sensor and vehicle speed buffer. If proper vehicle speed is present on the appropriate status screens of the 3176 (7X1055) DDT or the (8T8697) ECAP service tools during road test than Step 6 is not necessary.6. Pin D to pin A (static check): Disconnect the magnetic pickup (in transmission) from the input wires of the vehicle speed buffer.* Voltage should be 4.5 to 7.5 volts DC with the key on.
Vehicle Speed Buffer with Jumper Wire* With the jumper wire installed to the speed buffer input wires as shown, voltage is less than .75 volts DC with the key on. Diagnosis - If the voltages in both parts of Step 6 are correct, check the vehicle speed sensor per the manufactures specifications.In both parts of Step 6, if the voltage is 4.5 to 7.5 volts DC and does not change when the input wires are opened or jumpered: Remove breakout "T" and check wire from J7 pin D to J14 pin D for ground or open.* Remove the jumper wire and reconnect the magnetic pickup to vehicle speed buffer.7. Pin E to pin A:* Less than 1.0 volt DC with key on and foot pedal in low idle position.* More than 3.5 volts DC with foot pedal in high idle position. Diagnosis - Disconnect breakout "T". With the truck schematic, check wire E for continuity from J7 pin E to J11 pin C. Also check that wire E is not grounded to the chassis. Check for open or poor connections. Proceed to J11 connector tests. Steps 8, 9, 10, and 11 can be more easily checked using the appropriate status screens of the 3176 (7X1055) DDT or (8T8697) ECAP service tools.8. Pin F to pin A:* More than 4.5 volts DC with the cruise control switch in the off position and the key on.* Less than .5 volts DC with the cruise control switch in the on position and the key on. Diagnosis - Disconnect breakout "T" and check the individual switch circuits for open, ground or faulty switch. Switch circuit must have less than 2.5 ohms resistance and more than 5000 ohms resistance to chassis ground.9. Pin G to pin A:* Less than .5 volts DC with the key on.* More than 4.5 volts DC with the clutch disengaged and the key on. Diagnosis - Disconnect breakout "T" and check the individual switch circuits for open, ground or faulty switch. Switch circuit must have less than 2.5 ohms resistance and more than 5000 ohms resistance to chassis ground.10. Pin H to pin A:* More than 4.5 volts DC with set resume switch in the center position and the key on.* Les than .5 volts DC in resume (decelerate) position with the key on. Diagnosis - Disconnect breakout "T" and check the individual switch circuits for open, ground or bad switch. Switch circuit must have less than 2.5 ohms resistance and more than 5000 ohms resistance to chassis ground.11. Pin J to pin A:* More than 4.5 volts DC with set resume switch in the center position and the key on.* Less than .5 volts DC in set (accelerate) position with the key on. Diagnosis - Disconnect breakout "T" and check the individual switch circuits for open, ground or faulty switch. Switch circuit must have less than 2.5 ohms resistance and more than 5000 ohms resistance to chassis ground.12. Disconnect breakout "T" and reconnect P7 to J7. Secure the locking ring.If problem has not been resolved, proceed to the next connector to be tested as shown in the Operational Problem Chart section.If this is the last connector to be checked for the operational problem being investigated:* The problem could lie within the customer specified parameters. Check with the 3176 (7X1055) DDT or the (8T8697) ECAP.* Review connector tests again.


Parts medallion Force:

F694366 1
 
F694366 1 MEDALLION-US MARINE (RED) (89A/91D)
H0091H84D, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H0152C84K, H0152S89A, H0407E92C, H0507A91A, H0507A91C, H0507A92A, H0507E91B, H0706A91B, H0851X88A, H0853F88B, H0903E91D, H0903E91H, H0903F91A, H0903F91C, H090LD90B, H090LD90C, H090LD91
819169
 
819169 MEDALLION-FORCE
H0052C88A, H0091H84D, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H0152C84K, H0152S89A, H0407E92C, H0706A91B, H0903E91H, H1201A90A, H1501E89A
F663366-1
 
F663366-1 MEDALLION, "FORCE"
H0352F90B, H0352F90C, H0353E91A, H0353E91B, H0357G90A, H0507A90A, H0507A90B, H0507A90C, H0507A90D, H0507A91A, H0507A91C, H0507A92A, H0507E91B, H085LD89A, H085LD89B, H085LD89C, H0903E91D, H0903F90B, H0903F90C, H0903F91A, H0903F91C, H0906A90A, H090LD90
FZ721366
 
FZ721366 MEDALLION (Gold FORCE)
H0407E92C, H0507A91A, H0507A91C, H0507A92A, H0507E91B, H0903E91D, H0903E91H, H0903F91A, H0903F91C, H1201A90A, H1501E89A
Back to top