826164 Force NUT (7/8-14)


826164 NUT (7/8-14) Force H040312RD, H040312SD, H075312SD, H090412SD, H120412SD NUT
826164 NUT (7/8-14) Force
Rating:
88

Buy NUT (7/8-14) 826164 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 14
 

Force entire parts catalog list:

H040312RD 1995
H040312SD 1996,1997
H075312SD 1996,1997
H090412SD 1996,1997
H120412SD 1996,1997

Information:

Introduction
This Special Instruction provides the procedure in order to repower a 988F Wheel loader. The replacement engine will be a Tier II level 3408E engine. Refer to Table 1 for the engine arrangement numbers. The 988F Wheel Loader was originally equipped with a 3408B engine. The original 3408B engine is not regulated for emissions. This Special Instruction will provide the information in order to install the Tier II level replacement engine.Note: Ambient capability of this repower is limited to 43° C (109° F) maximum.
Table 1
Engine Arrangements
Original Engine Replacement Engine
4P-4988
122-1116
143-0029 262-7247(1)
(1) New Repower EngineThis Special Instruction does not include procedures that can be found in your existing manuals. Refer to the original Service Manual, Parts Manual, and Operation and Maintenance Manual for more information.When you have completed this procedure, prepare the machine for service. Refer to the Operation and Maintenance Manual.Note: Do not perform any procedure in this Special Instruction until the information has been read and understood.Reference: Service Manual, Parts Manual, Operation and Maintenance Manual.Note: This instruction contains some procedures that come from dealer feedback. The emissions replacement engine is not a direct replacement. Additional parts and additional labor hours may be needed in order to complete this engine replacement. Variations in machine serial number breaks or options could cause a discrepancy in the modifications, parts needed, and labor hours to complete this repower. This documentation is a guideline for Caterpillar dealer personnel in order to complete the repower procedure. If errors are found, submit feedback in SIS Web or contact the Emissions Solutions Group. The information that follows will be required:
Machine serial number
Original engine arrangement number
Original engine serial number
Emissions engine arrangement number
Details of the error
Photos of the error and photos after the proposed solutionRegistering the Retrofit
Reference: Special Instruction, REHS5097, "Instructions to Register the Retrofit"Documenting changes to a machine configuration is an advantage to Caterpillar and the dealer technicians that are sent to repair a machine. By identifying that the machine has been reconfigured, the technician will have a better opportunity to have the correct parts, tooling, and service information. Identifying that the machine has been reconfigured will also allow Caterpillar to include the retrofitted serial numbers in applicable service literature.Safety
Personal injury or death can result from sudden machine movement.Sudden movement of the machine can cause injury to persons on or near the machine.To prevent injury or death, make sure that the area around the machine is clear of personnel and obstructions before operating the machine.
Do not attempt to assemble this machine until you read and you understand the assembly instructions.Improper assembly procedures could result in injury or death.
Personal injury or death can result from improper lifting or blocking.When a hoist or jack is used to lift any part or component, stand clear of the area. Be sure the hoist or jack has the correct capacity to lift a component. Install blocks or stands before performance of any work under a heavy component.Approximate weights of the components are shown. Clean all surfaces where parts are to be installed.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Welding on Machines and Engines with Electronic Controls
Proper welding procedures are necessary in order to avoid damage to the electronic controls and to the bearings. When possible, remove the component that must be welded from the machine or the engine and then weld the component. When welding near an electronic control on the machine or the engine, temporarily remove the electronic control in order to prevent heat-related damage. The following steps should be followed in order to weld on a machine or an engine with electron


Parts nut Force:

64015
 
64015 NUT (1/4-20)
H005201RS, H005201SD, H005201TS, H005201UD, H0052C88A, H0091H84D, H009201RS, H009201SD, H009201UD, H009201US, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H015201RS, H015201US, H015211SS, H0152C84K, H0152S89A, H025201RD, H025201TD, H025201T
79989
 
79989 NUT (10-24)
H0052C88A, H040312RD, H0407E92C, H0706A91B, H0903E91H, H1201A90A, H1501E89A
34059
 
34059 NUT (#10-32)
H0407E92C, H0706A91B, H075312SD, H075312UD, H0903E91H, H1201A90A, H1501E89A
72008
 
72008 NUT (.250-20)
H040312RD, H040312SD, H040312UD, H0407E92C, H0706A91B, H075312SD, H075312UD, H075412VD, H090312RD, H0903E91H, H090412SD, H090412UD, H090422VD, H1201A90A, H120412RD, H120412SD, H120412UD, H1501E89A
35778
 
35778 NUT(.500-20)
H0407E92C, H0706A91B, H075312SD, H075312UD, H0903E91H, H1201A90A, H1501E89A
91962
 
91962 NUT (.500-20)
H040312RD, H040312SD, H040312UD, H0407E92C, H0706A91B, H075312SD, H075312UD, H075412VD, H090312RD, H0903E91H, H090412SD, H090412UD, H090422VD, H1201A90A, H120412RD, H120412SD, H120412UD, H1501E89A
826833 6
 
826833 6 NUT (M6)
H040312RD, H040312SD, H040312UD, H075312SD, H075312UD, H075412VD, H090412SD, H090412UD, H090422VD, H120412SD, H120412UD
40119 10
 
40119 10 NUT (M10 X 1.5) (MANUAL TILT MODELS)
H040312RD, H040312SD, H040312UD
Back to top