F664025 Force PAD, INSULATING


F664025 PAD, INSULATING Force H0853F89E, H0853F89F, H0853F89G, H0856A89H, H0856L89D, H085LD89A, H085LD89B, H085LD89C, H0903E91H, H0903F90B, H0903F90C, H0903F91A, H0903F91C, H0906A90A, H090LD90A, H1201A90A, H120LD90A, H120LD90B, H1251A89A, H1251A89D, H1251A89E, H125LD89A, H125LD89 PAD
F664025 PAD, INSULATING Force
Rating:
38

Buy PAD, INSULATING F664025 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 78
 

Force entire parts catalog list:

H0853F89E 1989
H0853F89F 1989
H0853F89G 1989
H0856A89H 1989
H0856L89D 1989
H085LD89A 1989
H085LD89B 1989
H085LD89C 1989
H0903E91H 1991,1992,1993,1994
H0903F90B 1990
H0903F90C 1990
H0903F91A 1991
H0903F91C 1991
H0906A90A 1990
H090LD90A 1990
H1201A90A 1990,1991,1992,1993,1994
H120LD90A 1990
H120LD90B 1990
H1251A89A 1989
H1251A89D 1989
H1251A89E 1989
H125LD89A 1989
H125LD89B 1989
H1501E89A 1989,1990,1991,1992,1993,1994

Information:

1. Drain the coolant from the cooling system to a level below that of the water pump into a suitable container for storage or disposal.2. Remove elbow (1).3. Remove bolts (4) that hold cover (2) to the water pump. Remove bolts (5) that hold elbow (3) to cover (2).4. Remove line (6).5. Remove cover (2). Remove elbow (3). 6. Remove four bolts (7).7. Remove nuts (8) and one bolt (not shown). Remove the water pump.Install Water Pump
1. Put the water pump in position on the timing gear cover. Install nuts (8) and one bolt that hold the pump to the timing gear cover.2. Install four bolts (7). 3. Put clean engine oil or glycerin on O-ring seals (9). Install elbow (3). 4. Put cover (2) in position on the water pump. Install bolts (4) that hold the cover to the water pump and bolts (5) that hold elbow (3) to the cover.5. Install elbow (1).6. Install line (6).7. Refill the cooling system to the proper level. See the Operation & Maintenance Manual.Disassemble Water Pump
Start By:a. remove water pump 1. Remove O-ring seal (1) from adapter (2).2. Remove adapter (2) with a screwdriver. Remove the seal from the edge of adapter (2).3. Remove bolt (3) and washer. 4. Remove impeller (4) from the water pump housing with Tool (A). 5. Remove seal assembly (5). Remove ring and seal (6). 6. Remove the bolt and washer that hold gear (7) on the water pump shaft.7. Remove gear (7) with Tool (B).8. Remove bolts and retainer (9).9. Remove O-ring seal (8). 10. Remove shaft (10) and bearings as a unit.11. Remove bearing (11), spacer (12) and bearing (13) from shaft (10).12. Remove lip seal from the gear side of the water pump housing. Remove ring and seal from the impeller side of the water pump housing.Assemble Water Pump
1. Put clean engine oil or glycerin on the lip of seal (1). Use Tool (A) to install seal (1) as shown. Make sure the seal is flush in the counterbore. 2. Install bearing (4), spacer (3) and bearing (5) on shaft (2). Install shaft (2) in the water pump housing. 3. Install retainer (7) and O-ring seal (8).4. Install gear (6). Install washer and bolt that hold gear (6) to shaft (2).
Clean water only is permitted for use as a lubricant for assistance at installation. Do not damage or put hands on the wear surface of the carbon ring or the ceramic ring. Install the ceramic ring with the smoothest face of the ring toward the carbon seal assembly.
5. Put ceramic ring (10) in position in the rubber seal (9). Use hand pressure and the tool (which is with the replacement ring) to install the ceramic ring in the water pump housing. 6. Remove the spring from seal assembly (11). Use the tool that is with the replacement ring to install seal assembly (11). Push the seal assembly on the shaft until the carbon ring (on the seal assembly) makes light contact with the ceramic ring. 7. Install spring (12) on the seal assembly and impeller (13) on the shaft. Install the bolt and washer on the shaft. Tighten the bolt to a torque of 39 3 N m (29 2 lb ft). 8. Install O-ring seals (14) on adapter (15). Put clean engine oil on O-ring seals. Lubricate the bore of the water pump housing lightly with glycerin.9. Install adapter (15) in the water pump housing. Make sure the notch in the adapter is in alignment with dowel (16).End By:a. install water pump


Parts pad Force:

F660025
 
F660025 PAD, INSULATING
H085LD89A, H085LD89B, H085LD89C, H090LD90A, H120LD90A, H125LD89A, H125LD89B
F695025
F691025
 
F691025 PAD-Terminal Block
H0507A90A, H0507A90B, H0507A90C, H0507A90D, H0507A91A, H0507A91C, H0507A92A, H0507E91B, H090LD90B, H090LD90C, H090LD91D, H120LD90C, H120LD91B, H120LD91D, H120LD92B, H1501E89A
Back to top