F1978 SPRING PIN FOR MANUAL START MODELS Force
H0060B76A, H0060B78B, H0060H79C, H0060H80D, H0062B78J, H0062H79K, H0062H79M, H0064H80F, H0067H79C, H0070B79A, H0072H79B, H0072H80C, H0075H79A, H0082H76G, H0082H78J, H0082H79K, H0091B80B, H0091H79A, H0091H83C, H0091H84D, H0092B80G, H0092H79F, H0092H81
SPRING
Price: query
Rating:
Compatible models:
H0060B76A
H0060B78B
H0060H79C
H0060H80D
H0062B78J
H0062H79K
H0062H79M
H0064H80F
H0067H79C
H0070B79A
H0072H79B
H0072H80C
H0075H79A
H0082H76G
H0082H78J
H0082H79K
H0091B80B
H0091H79A
H0091H83C
H0091H84D
H0092B80G
H0092H79F
H0092H81H
H0092H81J
H0092H83K
H0092H84L
H0094H81F
H0101B78A
H0102H76C
H0102H78E
H0121B79A
H0122H79E
H0152B78D
H0152B83J
H0152C84K
H0152H79E
H0152H80F
H0152H81G
H0152S89A
H0202B80L
H0202B81M
H0202H79K
H0202H82N
H0252B83G
H0252H77B
H0252H78C
H0252H78D
H0254H75A
H0306B80C
H0307H81D
H0350H78L
H0351H76K
H0352F90B
H0352F90C
H0353E91A
H0353E91B
H0357C86A
H0357C87A
H0357F88A
H0357F89C
H0357G90A
H0357H83N
H0606H84A
Force
Force entire parts catalog list:
- MOTOR LEG » F1978
- ENGINE COVER AND SUPPORT PLATE » F1978
- ENGINE COVER AND SUPPORT PLATE » F1978
- ENGINE COVER AND SUPPORT PLATE » F1978
- ENGINE COVER AND SUPPORT PLATE » F1978
- ENGINE COVER AND SUPPORT PLATE » F1978
- MOTOR LEG » F1978
- ENGINE COVER AND SUPPORT PLATE » F1978
- ENGINE COVER AND SUPPORT PLATE » F1978
- ENGINE COVER AND SUPPORT PLATE » F1978
- ENGINE COVER AND SUPPORT PLATE » F1978
- ENGINE COVER AND SUPPORT PLATE » F1978
- ENGINE COVER AND SUPPORT PLATE » F1978
- MOTOR LEG » F1978
- ENGINE COVER AND SUPPORT PLATE » F1978
- MOTOR LEG » F1978
- MOTOR LEG » F1978
- MOTOR LEG » F1978
- MOTOR LEG » F1978
- MOTOR LEG » F1978
- MOTOR LEG » F1978
- MOTOR LEG » F1978
- MOTOR LEG » F1978
- MOTOR LEG » F1978
- MOTOR LEG » F1978
- MOTOR LEG » F1978
- MOTOR LEG » F1978
- MOTOR LEG » F1978
- MOTOR LEG » F1978
- MOTOR LEG » F1978
- MOTOR LEG » F1978
- MOTOR LEG » F1978
- MOTOR LEG » F1978
- MOTOR LEG » F1978
- MOTOR LEG » F1978
- MOTOR LEG » F1978
- MOTOR LEG » F1978
- MOTOR LEG » F1978
H0202B80L 1980
H0202B81M 1981
H0202H79K 1979
H0202H82N 1982
H0252B83G 1983,1984
H0252H77B 1977
H0252H78C 1978
H0252H78D 1978
H0254H75A 1975,1976
H0306B80C 1980
- MOTOR LEG » F1978
- MOTOR LEG » F1978
- MOTOR LEG » F1978
- MOTOR LEG » F1978
- 5H246 TILLER HANDLE KIT » F1978
- 5H246 TILLER HANDLE KIT » F1978
- 5H246 TILLER HANDLE KIT » F1978
- 5H246 TILLER HANDLE KIT » F1978
- MOTOR LEG » F1978
- MOTOR LEG » F1978
- MOTOR LEG » F1978
- 5H246 TILLER HANDLE KIT » F1978
- 5H246 TILLER HANDLE KIT » F1978
- MOTOR LEG » F1978
- POWER HEAD » F1978
Information:
Check Connectors for Moisture and Corrosion
Illustration 1 g01131211
Detail A illustrates the incorrect angle of wire entry into the connector. The wire should enter the connector at a perpendicular angle. (typical example)
Inspect all the harnesses. Ensure that the routing of the wiring harness allows the wires to enter the face of each connector at a perpendicular angle. Otherwise, the wire will deform the seal bore. The damaged seal will create a path for the entrance of moisture. Verify that the seals for the wires are sealing correctly.
Illustration 2 g01131276
Diagram for the installation of a connector plug (typical example)
(1) Electronic Control Module (ECM) connector
(2) Correctly inserted plug
(3) Incorrectly inserted plug Ensure that the sealing plugs are in place. If any of the plugs are missing, replace the plug. Ensure that the plugs are inserted correctly into the connector.
Illustration 3 g01131019
Seal for a three-pin connector (typical example)
Illustration 4 g01131165
Seal for the ECM connector (typical example)
Disconnect the suspect connector and inspect the connector seal. Ensure that the seal is in good condition. If necessary, replace the connector.Thoroughly inspect the connectors for evidence of moisture entry.Note: Some minor seal abrasion on connector seals is normal. Minor seal abrasion will not allow the entry of moisture.If moisture or corrosion is evident in the connector, the source of the moisture entry must be found. The source of the moisture entry must be repaired. If the source of the moisture entry is not repaired, the fault will recur. Simply drying the connector will not fix the fault. Check the following items for the possible moisture entry path:
Missing seals
Incorrectly installed seals
Nicks in exposed insulation
Improperly mated connectorsMoisture can also travel to a connector through the inside of a wire. If moisture is found in a connector, thoroughly check the connector harness for damage. Also check other connectors that share the harness for moisture.Check the Wires for Damage to the Insulation
Carefully inspect each wire for signs of abrasion, nicks, and cuts.Inspect the wires for the following conditions:
Exposed insulation
Rubbing of a wire against the engine
Rubbing of a wire against a sharp pointCheck all of the fasteners for the harness and the ECM in order to verify that the harness is correctly secured. Also check all of the fasteners in order to verify that the harness is not compressed. Pull back the harness sleeves in order to check for a flattened portion of wire. A fastener that has been overtightened flattens the harness. This damages the wires that are inside the harness.Inspect the Connector Terminals
Visually inspect each terminal in the connector. Verify that the terminals are not damaged. Verify that the terminals are correctly aligned in the connector and verify that the terminals are correctly located in the connector.Perform a Pull Test on Each Wire Terminal Connection
Illustration 5 g01131435
Receptacle lock wedge (typical example)
Ensure that the locking wedge for the connector is installed correctly. Terminals cannot be retained inside the connector if the locking wedge is not installed correctly.Perform the 45 N (10 lb) pull test on each wire. Each terminal and each connector should easily withstand 45 N (10 lb) of tension and each wire should remain in the connector body. This test checks whether the wire was correctly crimped in the terminal and whether the terminal was correctly inserted into the connector.Check Individual Pin Retention into the Socket
Illustration 6 g01131604
Diagram for testing pin retention (typical example)
Verify that the sockets provide good retention for the pins. Insert a new pin into each socket one at a time in order to check for a good grip on the pin by the socket.Check the Locking Mechanism of the Connectors
Ensure that the connectors lock correctly. After you lock the connectors, ensure that the two halves cannot be pulled apart.Verify that the latch tab of the connector is correctly latched. Also verify that the latch tab of the connector returns to the locked position.Check the Allen Head Screws on the Connectors
Visually inspect the allen h
Illustration 1 g01131211
Detail A illustrates the incorrect angle of wire entry into the connector. The wire should enter the connector at a perpendicular angle. (typical example)
Inspect all the harnesses. Ensure that the routing of the wiring harness allows the wires to enter the face of each connector at a perpendicular angle. Otherwise, the wire will deform the seal bore. The damaged seal will create a path for the entrance of moisture. Verify that the seals for the wires are sealing correctly.
Illustration 2 g01131276
Diagram for the installation of a connector plug (typical example)
(1) Electronic Control Module (ECM) connector
(2) Correctly inserted plug
(3) Incorrectly inserted plug Ensure that the sealing plugs are in place. If any of the plugs are missing, replace the plug. Ensure that the plugs are inserted correctly into the connector.
Illustration 3 g01131019
Seal for a three-pin connector (typical example)
Illustration 4 g01131165
Seal for the ECM connector (typical example)
Disconnect the suspect connector and inspect the connector seal. Ensure that the seal is in good condition. If necessary, replace the connector.Thoroughly inspect the connectors for evidence of moisture entry.Note: Some minor seal abrasion on connector seals is normal. Minor seal abrasion will not allow the entry of moisture.If moisture or corrosion is evident in the connector, the source of the moisture entry must be found. The source of the moisture entry must be repaired. If the source of the moisture entry is not repaired, the fault will recur. Simply drying the connector will not fix the fault. Check the following items for the possible moisture entry path:
Missing seals
Incorrectly installed seals
Nicks in exposed insulation
Improperly mated connectorsMoisture can also travel to a connector through the inside of a wire. If moisture is found in a connector, thoroughly check the connector harness for damage. Also check other connectors that share the harness for moisture.Check the Wires for Damage to the Insulation
Carefully inspect each wire for signs of abrasion, nicks, and cuts.Inspect the wires for the following conditions:
Exposed insulation
Rubbing of a wire against the engine
Rubbing of a wire against a sharp pointCheck all of the fasteners for the harness and the ECM in order to verify that the harness is correctly secured. Also check all of the fasteners in order to verify that the harness is not compressed. Pull back the harness sleeves in order to check for a flattened portion of wire. A fastener that has been overtightened flattens the harness. This damages the wires that are inside the harness.Inspect the Connector Terminals
Visually inspect each terminal in the connector. Verify that the terminals are not damaged. Verify that the terminals are correctly aligned in the connector and verify that the terminals are correctly located in the connector.Perform a Pull Test on Each Wire Terminal Connection
Illustration 5 g01131435
Receptacle lock wedge (typical example)
Ensure that the locking wedge for the connector is installed correctly. Terminals cannot be retained inside the connector if the locking wedge is not installed correctly.Perform the 45 N (10 lb) pull test on each wire. Each terminal and each connector should easily withstand 45 N (10 lb) of tension and each wire should remain in the connector body. This test checks whether the wire was correctly crimped in the terminal and whether the terminal was correctly inserted into the connector.Check Individual Pin Retention into the Socket
Illustration 6 g01131604
Diagram for testing pin retention (typical example)
Verify that the sockets provide good retention for the pins. Insert a new pin into each socket one at a time in order to check for a good grip on the pin by the socket.Check the Locking Mechanism of the Connectors
Ensure that the connectors lock correctly. After you lock the connectors, ensure that the two halves cannot be pulled apart.Verify that the latch tab of the connector is correctly latched. Also verify that the latch tab of the connector returns to the locked position.Check the Allen Head Screws on the Connectors
Visually inspect the allen h
Parts spring Force:
F8096
F8096 SPRING LOCKWASHER
H0091H83C, H0091H84D, H0095B80F, H0095B81G, H0095H82H, H0125H79E, H0152B78D, H0202B80L, H0202B81M, H0202H79K, H0202H82N, H0252B83G, H0252H77B, H0252H78C, H0252H78D, H0254H75A, H0257F88A, H0257F88B, H0306B80C, H0307H81D, H0350H78L, H0351H76K, H0352F90
F8056
F8056 SPRING LOCKWASHER
H0202B81M, H0202H79K, H0252B83G, H0252H77B, H0252H78D, H0254H75A, H0257F88A, H0257F88B, H0306B80C, H0307H81D, H0350H78L, H0351H76K, H0352F90B, H0352F90C, H0353E91A, H0353E91B, H0355D89A, H0356F89B, H0356H75F, H0357C86A, H0357C87A, H0357C88B, H0357F88
F458424
F458424 SPRING, STARTER PAWL PLATE
H0202B80L, H0202B81M, H0202H79K, H0202H82N, H0252B83G, H0252H77B, H0252H78C, H0252H78D, H0254H75A, H0306B80C, H0350H78L, H0351H76K
F458846
F458846 SPRING, STARTER INTERLOCK LEVER
H0202B80L, H0202B81M, H0202H79K, H0202H82N, H0252B83G, H0252H77B, H0252H78C, H0252H78D, H0254H75A, H0306B80C, H0350H78L, H0351H76K
F1703
F1703 SPRING LOCKWASHER
H0257F88A, H0257F88B, H0352F90B, H0352F90C, H0353E91A, H0355D89A, H0356F89B, H0357C88B, H0357F89C, H0357G90A, H0504H88C, H0504H88D, H0504P89B, H0505C89B, H0507A89C, H0507A89D, H0507A90A, H0507A90B, H0507A90C, H0507A90D, H0507A91A, H0507A91C, H0507A92
F318895
F8553
F8553 SPRING PIN
H0092B80G, H0092H79F, H0092H81H, H0092H81J, H0092H83K, H0092H84L, H0094H81F, H0102H76C, H0102H78E, H0122H79E, H0152B78D, H0152B83J, H0152C84K, H0152H79E, H0152H80F, H0152H81G, H0152S89A
F286414
F286414 SPRING, LEG WATER BRACKET
H0091B80B, H0091H79A, H0091H83C, H0091H84D, H0092284D, H0092B80G, H0092H79F, H0092H81H, H0092H81J, H0092H83K, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H0094H81F, H0095B80F, H0095B81G, H0095H82H, H0101B78A, H0102H76C, H0102H78E, H0121B79A, H0122H79