F691312 Force PIN


F691312 PIN Force H120LD90C, H120LD91B PIN
F691312 PIN Force
Rating:
33

Buy PIN F691312 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 44
 

Compatible models:

Force entire parts catalog list:

H120LD90C 1990
H120LD91B 1991

Information:

Recommended Actions
Complete the procedure in the order in which the steps are listed.
Table 1
Troubleshooting Test Steps Values Results
1. Leak in the Engine Oil Cooler
A. Check for leaks in the engine oil cooler. Refer to Testing and Adjusting for the proper procedure.
Oil Cooler
Result: A leak is found in the engine oil cooler.
Repair: Install a new oil cooler core. Refer to the Disassembly and Assembly manual.
Flush the cooling system. Refer to the Operation and Maintenance Manual for the proper flushing procedure. Refill the cooling system with the proper coolant. Refer to the Operation and Maintenance Manual for the correct coolant and capacities.
Check the oil for coolant. If coolant is found in the oil, drain the crankcase. Refill the crankcase with the proper oil after the leak has been repaired. Refer to the Operation and Maintenance Manual for the correct oil capacities and viscosity.
Result: A leak was not found in the engine oil cooler.
Proceed to Test Step 2.
2. Leak in the Power Train Oil Cooler
A. Check for leaks in the power train oil cooler. Refer to Testing and Adjusting for the proper procedure
Power Train Cooler
Result: A leak is found in the power train oil cooler.
Repair: Install a new oil cooler core. Refer to the Disassembly and Assembly manual.
Flush the cooling system. Refer to the Operation and Maintenance Manual for the proper flushing procedure. Refill the cooling system with the proper coolant. Refer to the Operation and Maintenance Manual for the correct coolant and capacities.
Check the oil for coolant. If coolant is found in the oil, drain the crankcase. Refill the oil after the leak has been repaired. Refer to the Operation and Maintenance Manual for the correct oil capacities and viscosity.
Result: A leak was not found in the power train oil cooler.
Proceed to Test Step 3.
3. Water-Cooled Turbocharger (if equipped)
A. Inspect the turbocharger for cracks.
B. Remove the oil drain line from the turbo and pressurize the cooling system, Refer to Testing and Adjusting, "Cooling System - Test".
C. Check the turbocharger for coolant leakage.
Turbocharger
Result: The turbocharger is cracked.
Repair: Replace the turbocharger. Refer to the engine Disassembly and Assembly for the correct procedure.
Flush the cooling system, Refer to the Operation and Maintenance Manual for the correct procedure.
Refill the cooling system with the proper coolant. Refer to the Operation and Maintenance Manual for the correct coolant and capacities.
Check the oil for coolant. If coolant is found in the oil, drain the oil. Refill the oil after the leak has been repaired. Refer to the Operation and Maintenance Manual for the correct oil capacities.
Result: The turbocharger is not cracked.
Proceed to Test Step 4.
4. Cylinder Head Gasket
A. Remove the cylinder head. Refer to the Disassembly and Assembly manual.
B. Check the cylinder liner projection. Refer to the Systems Operation/Testing and Adjusting manual.
C. Install a new cylinder head gasket and new water seals in the spacer plate. Refer to the Disassembly and Assembly manual.
Cylinder Head Gasket
Result: New cylinder head gasket and water seals were installed.
Proceed to Test Step 5.
5. Cylinder Head
A. Check for cracks in the cylinder head. Perform a leak test on the cylinder head. Refer to System Operation, Testing and Adjusting for the proper procedure for checking the cylinder head.
Cylinder Head
Result: A crack is found in the cylinder head.
Repair: Repair the cylinder head and/or replace the cylinder head. Refer to the Disassembly and Assembly manual.
Result: A crack is not found in the cylinder head.
Proceed to Test Step 6.
6. Cylinder Block
A. Inspect the cylinder block for cracks.
Cylinder Block
Result: A crack is found in the cylinder block.
Repair: Repair the cylinder block or replace the cylinder block. Inspect the top deck. Refer to the Reuse and Salvage Guidelines for the proper inspection procedure.


Parts pin Force:

F84871-1
 
F84871-1 PIN, GEAR SHIFT
H0700H79A, H0709B79A, H0750H79A, H0756H80F, H0756H81G, H0756H82H, H0757B79E, H0758H80B, H0758H82E, H0759H79A, H0850H79A, H0850H80A, H0850H81C, H0851H79A, H0851X88A, H0853F88B, H0853F89C, H0853F89E, H0853F89F, H0853F89G, H0855H79A, H0856A89A, H0856A89
F694017
PIN, PISTON
F694017 PIN, PISTON
H0505C89B, H0507A89C, H0507A89D, H0507A90A, H0507A90B, H0507A90C, H0507A90D, H0507A91A, H0507A91C, H0507A92A, H0507E91B, H0507Z89B, H085LD89A, H085LD89B, H085LD89C, H0903E91D, H0903F91A, H0903F91C, H090LD90A, H090LD90B, H090LD90C, H090LD91D, H120LD90
F695037
 
F695037 PIN, TRIM CYLINDER
H085LD89A, H085LD89B, H085LD89C, H090LD90A, H090LD90B, H090LD90C, H090LD91D, H120LD90A, H120LD90B, H120LD90C, H120LD91B, H120LD91D, H120LD92B, H125LD89A, H125LD89B
F8580
 
F8580 PIN, LOCATING
H085LD89A, H085LD89B, H085LD89C, H0903E91H, H090LD90A, H090LD90B, H090LD90C, H090LD91D, H1201A90A, H120LD90A, H120LD90B, H120LD90C, H120LD91B, H120LD91D, H120LD92B, H125LD89A, H125LD89B, H1501E89A
F695440
 
F695440 PIN, PIVOT
H085LD89A, H085LD89B, H085LD89C, H090LD90A, H090LD90C, H120LD90A, H120LD90B, H120LD90C, H125LD89A, H125LD89B
F719372
 
F719372 PIN-Water Jacket Tube
H0706A91B, H075312SD, H075312UD, H075412VD, H090312RD, H0903E91D, H0903E91H, H0903F91A, H0903F91C, H090412SD, H090412UD, H090422VD, H090LD90B, H090LD90C, H090LD91D, H1201A90A, H120412RD, H120412SD, H120412UD, H120LD90B, H120LD90C, H120LD91B, H120LD91
F2419
 
F2419 PIN-Spring
H0903E91D, H0903E91H, H0903F90B, H0903F90C, H0903F91A, H0903F91C, H090LD90B, H090LD90C, H090LD91D, H1201A90A, H120LD90C, H120LD91B, H120LD91D, H120LD92B, H1501E89A
F8586
 
F8586 PIN-Dowel
H0903E91D, H0903E91H, H0903F90C, H0903F91A, H0903F91C, H090LD90B, H090LD90C, H090LD91D, H1201A90A, H120LD90B, H120LD90C, H120LD91B, H120LD91D, H120LD92B, H1501E89A
Back to top