819042A 3 Force PISTON, .030 OVERSIZE


819042A 3 PISTON, .030 OVERSIZE Force H0903E91D PISTON
819042A 3 PISTON, .030 OVERSIZE Force
Rating:
83

Buy PISTON, .030 OVERSIZE 819042A 3 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: &nbsp
 

Compatible models:

H0903E91D   Force

Force entire parts catalog list:

H0903E91D 1991

Information:


Table 1
Troubleshooting Test Steps Values Results
1. Determine the Problem
A. Determine the communication problem.
If an indicator other than the "POWER" indicator is illuminated when Cat ET is not communicating with an ECM, disconnect and reconnect the communication adapter.
Communication problem
Result: Both indicators on the communication adapter are not flashing.
Proceed to Test Step 2.
Result: Cat ET indicates that the engine is serviced on both links.
Proceed to Test Step 2.
Result:Cat ET displays a message that indicates the firmware in the communication adapter does not support communication on both data links.
Proceed to Test Step 3.
Result: Cat ET displays an Error" #142 The interface hardware is not responding" message.
Proceed to Test Step 3.
Result:Cat ET displays a message that indicates that Cat ET cannot find an exact match for the software version in the ECM.
Update Cat ET to the latest available version.
Result: The power indicator is not illuminated.
Proceed to Test Step 5.
2. Verify that the Correct Communication Adapter is Being Used
A. A 317-7484 Communication Adapter Gp must be used to communicate. The following communication adapters cannot be used because the communication adapters do not communicate over both data links:
1. Wireless communication adapter
2. 7X-1701 Communication Adapter As
B. Determine the communication adapter that is being used.
Communication adapter
Result: An incorrect communication adapter is being used.
Connect a correct communication adapter. Refer to Troubleshooting, "Electronic Service Tools", if necessary.
Attempt to establish communication. Continue with this procedure if the communication adapter does not communicate on both data links.
Result: A correct communication adapter is being used. However, the "Power" indicator is not illuminated.
Proceed to Test Step 5.
Result: A correct communication adapter is being used. The "Power" indicator is illuminated.
Proceed to Test Step 4.
3. Check the Version of the Firmware for the Communication Adapter
The version of the firmware for the communication adapter must be "3.0.0" or higher.
A. Electronically disconnect Cat ET. Verify that the "power" indicator on the communication adapter is illuminated.
B. Click on the "Utilities" menu.
C. Click on the "Comm Adapter II Toolkit" menu.
D. Wait for the tool kit to open. Then, click the "Utilities" menu.
E. Click "Application Firmware Flash".
F. Select the latest ".apf" file from the list.
G. Click "OK". Then, click "Begin Flash".
H. Wait for the "Flashes Completed Successfully" message to appear.
I. Click "Toolkit". Verify that the "Application Firmware Version (Serial IP)" is "3.0.0" or higher.
J. Attempt to connect Cat ET.
Firmware
Result: Cat ET communicates on both data links.
The problem is resolved.
Result: Cat ET does not communicate on both data links.
Proceed to Test Step 4.
4. Verify That Cat ET is Configured Correctly
Cat ET must be configured correctly in order to communicate on both data links.
A. Click on the "Utilities" menu.
B. Click on the "Preferences" menu.
C. Select the "Communications" tab.
D. Verify that "Caterpillar Communication Adapter II (Serial IP)" is selected.
If "Caterpillar Communication Adapter II (Serial IP)" is not an option for selection, the version of Cat ET is incorrect. Version "2007B" or higher must be used.
Update the version of Cat ET. Then, perform this Test Step again.
Configured correctly
Result: Cat ET communicates on both data links.
The problem is resolved.
Result: Cat ET does not communicate on both data links. The "POWER" indicator is not illuminated.
Proceed to Test Step 5.
Result: Cat ET does not communicate on both data links. The "POWER" indicator is illuminated.
Proceed to Test Step 6.
Table 2
E. Verify that the port is correct.
F. Verify that the "Enable Dual Data Link Service" option is checked.
G. Click "OK". Cat ET must reconnect in order for any changes to be used.
H. Electronically disconnect Cat ET if changes are made to any of the settings for communications. Electronically connect Cat ET. Attempt to establish communication. Observe the indicators on the communication adapter.
A "limited support" warning should not be displayed. The "J1939 / DeviceNet" and "CDL" indicators should be flashing. The indicator indicates that Cat ET is communicating on both data links.
Electrical power
Illustration 1 g02061279
Power terminals at the service tool connector
(Terminal A) +Battery
(Terminal B) −Battery
Table 3
Troubleshooting Test Steps Values Results
5. Check the Electrical Power to the Communication Adapter
A. Check for battery voltage at the service tool connector.
Electrical power
Result: Battery voltage is not present at the service tool connector.
Inspect the vehicles wiring and fuses. Determine the cause of the missing voltage. Make the necessary repairs.
Attempt to establish communication after the electrical power is at the service tool connector.
Proceed to Test Step 6 if the service tool does not communicate on both data links.
Result: Cat ET indicates that the engine is serviced on both links.
Verify that the cable between the service tool connector and the communication adapter is OK. Replace the cable, if necessary.
Replace the communication adapter if the following conditions are true:
1. There is power at the cables "DATA LINK" connector.
2. The communication adapters "POWER" indicator is not illuminated.
Table 4
Troubleshooting Test Steps Values Results
6. Check the Electrical Power to the ECM
A. Verify that the keyswitch is ON.
B. Verify that battery voltage is present at the terminals that are indicated in the Illustration. Be sure to connect the voltmeter between the "UNSWITCHED +BATTERY" terminals and the "-BATTERY" terminals.
C. Verify that battery voltage is present at P1-70.
Electrical power
Result: Battery voltage is missing from a P1 terminal.
Inspect the vehicles wiring and fuses. Determine the cause of the missing voltage. Make the necessary repairs.
Attempt to establish communication after the electrical power is at all of the appropriate P1 terminals. Continue with this procedure, if necessary.
Result: Battery voltage is present at all of the appropriate P1 terminals.
Proceed to the Test Step 7
7. Try to Establish Communication With a Bypass Harness
Connect the communication adapter t


Parts piston Force:

FA449015
 
FA449015 PISTON
H0700H79A, H0750H79A, H0756H81G, H0756H82H, H0758H80B, H0758H82E, H0759H79A, H0850H79A, H0850H80A, H0850H81C, H0851H79A, H0851X88A, H0853F88B, H0855H79A, H0856C87A, H0856C87B, H0856H82K, H0858B80C, H0858B82E, H0858C84H, H0859B79B, H0859H77A, H0859H78
FA528260
 
FA528260 PISTON RING SET FOR 2 PISTONS
H0903E91D, H0903F90B, H0903F90C, H0903F91A, H0903F91C, H090LD90B, H090LD90C, H090LD91D, H120LD90B, H120LD90C, H120LD91D, H120LD92B, H1400H79A, H1401H79A, H1405H79A, H1406H81D, H1408B80C, H1408H82D, H1408H83E
FSA528260
 
FSA528260 PISTON RING SET FOR 2 PISTONS .010 OVERSIZE
H0903E91D, H0903F90B, H0903F90C, H0903F91A, H0903F91C, H090LD90B, H090LD90C, H090LD91D, H120LD90B, H120LD90C, H120LD91B, H120LD91D, H120LD92B, H1400H79A, H1401H79A, H1405H79A, H1406H81D, H1408B80C, H1408H82D, H1408H83E
FT2990 1
 
FT2990 1 PISTON PIN TOOLS-PISTON PINS
H005201SD, H005201TS, H005201UD, H0052C88A, H0091H84D, H009201SD, H009201UD, H009201US, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H015201US, H015211SS, H0152C84K, H0152S89A, H025201RD, H025201TD, H025201TS, H0353E91A, H040312RD, H040312S
FA654015
 
FA654015 PISTON ASSEMBLY
H0851X88A, H0853F88B, H0856C87B, H0903E91D, H0903E91H, H0903F90B, H0903F90C, H0903F91A, H0903F91C, H0906A90A, H1201A90A, H1251A88A, H1251A88B, H1251A88C, H1251A89A, H1251A89B, H1251A89C, H1251A89D, H1251A89E, H1251F87B, H1501E89A
818129A 1
 
818129A 1 PISTON RINGS (2 PER SET) .030 OVERSIZE
H0903E91D, H090LD91D, H120LD91D, H120LD92B
F719015-3
819041A 3
Back to top