F40017-2 Force PISTON PIN


F40017-2 PISTON PIN Force H0257F88A, H0257F88B, H0306B80C, H0307H81D, H0350H78L, H0351H76K, H0352F90B, H0352F90C, H0352H77H, H0352H79L, H0353E91A, H0353E91B, H0353H78K, H0353H80M, H0353H81N, H0353H82P, H0355D89A, H0356F89B, H0356H75F, H0357C86A, H0357C87A, H0357C88B, H0357F88 PISTON
F40017-2 PISTON PIN Force
Rating:
68

Buy PISTON PIN F40017-2 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 4
 

Force entire parts catalog list:

H0257F88A 1988,1989
H0257F88B 1988,1989,1991
H0306B80C 1980
H0307H81D 1981
H0350H78L 1978
H0351H76K 1976
H0352F90B 1990
H0352F90C 1990
H0352H77H 1977,1978
H0352H79L 1979
H0353E91A 1991
H0353E91B 1991
H0353H78K 1978
H0353H80M 1980
H0353H81N 1981
H0353H82P 1982
H0355D89A 1989
H0356F89B 1989
H0356H75F 1975,1976,1977
H0357C86A 1986
H0357C87A 1987
H0357C88B 1988
H0357F88A 1988
H0357F89C 1989
H0357G90A 1990
H0357H83N 1983,1984
H0456B78J 1978
H0456B79K 1979
H0456B80L 1980,1981
H0457H82N 1982
H0457H83P 1983,1984
H0503B83A 1983
H0503H84B 1984
H0507B85A 1985
H0507C86A 1986
H0507C87A 1987
H0507H81A 1981
H0507H82B 1982
H0555H74G 1974,1976

Information:


Illustration 1 g00748963The cylinder block has seven main bearings. The main bearing caps are fastened to the cylinder block with two bolts per each cap.Removal of the oil pan allows access to the following components:
Crankshaft
Main bearing caps
Piston cooling jets
Oil pump
Illustration 2 g00748989The cylinder head is separated from the cylinder block by a nonasbestos fiber gasket with a steel backing. Coolant flows out of the cylinder block through gasket openings and into the cylinder head. This gasket also seals the oil supply and drain passages between the cylinder block and the cylinder head. The air inlet ports are on the left side of the cylinder head, while the exhaust ports are located on the right side of the cylinder head. There are two inlet valves and two exhaust valves for each cylinder. Each set of inlet valves and each set of exhaust valves is actuated at the same time by the use of a valve bridge. The valve bridge is actuated by the pushrod. Replaceable valve guides are pressed into the cylinder head. The hydraulically actuated electronically controlled unit injector is located between the four valves. Fuel is injected directly into the cylinders at very high pressure. A pushrod valve system controls the valves. Piston, Rings And Connecting Rods
Illustration 3 g00773509
(1) Piston
(2) Piston cooling jet
(3) Connecting rod High output engines with high cylinder pressures require two-piece articulated pistons. The two-piece articulated piston consists of a forged steel crown that is connected to an aluminum skirt by the piston pin. Refer to the Parts Manual in order to obtain information about the type of pistons that are used in a specific engine.
Illustration 4 g00773499
(4) Compression ring
(5) Intermediate ring
(6) Oil ring
(7) Forged steel crown
(8) Aluminum skirt All of the rings are located above the piston pin bore. The compression ring is a Keystone ring. Keystone rings have a tapered shape. The action of the ring in the piston groove that is tapered helps prevent seizure of the rings. Seizure of the rings is caused by deposits of carbon. The intermediate ring is rectangular with a sharp lower edge. The oil ring is a standard type of ring or a conventional type of ring. Oil returns to the crankcase through holes in the oil ring groove.Oil from the piston cooling jets sprays the underside of the pistons. The spray lubricates the pistons and the spray cools the pistons. The spray also improves the piston's life and the spray also improves the ring's life.The connecting rod has a taper on the pin bore end. Two bolts hold the connecting rod cap to the connecting rod. The connecting rod can be removed through the cylinder.Crankshaft
Illustration 5 g00770993
(1) Crankshaft
(2) Gear The crankshaft converts the linear motion of the pistons into rotational motion. A vibration damper is used at the front of the crankshaft to reduce torsional vibrations (twist on the crankshaft) that can cause damage to the engine.The crankshaft drives a group of gears on the front of the engine. The gear group drives the following devices:
Oil pump
Camshaft
Hydraulic oil pump
Air compressor
Power steering pumpIn addition, belt pulleys on the front of the crankshaft drive the following components:
Radiator fan
Water pump
Alternator
Refrigerant compressorHydrodynamic seals are used at both ends of the crankshaft to control oil leakage. The hydrodynamic grooves in the seal lip move lubrication oil back into the crankcase as the crankshaft turns. The front seal is located in the front housing. The rear seal is installed in the flywheel housing.
Illustration 6 g00816002
Schematic Of Oil Passages In Crankshaft
(1) Oil gallery
(2) Main bearings
(3) Rod bearings Pressure oil is supplied to all main bearings through drilled holes in the webs of the cylinder block. The oil then flows through drilled holes in the crankshaft in order to provide oil to the connecting rod bearings. The crankshaft is held in place by seven main bearings. A thrust bearing next to the rear main bearing controls the end play of the crankshaft.Vibration Damper
The force from combustion in the cylinders will cause the crankshaft to twist. This is called torsional vibration. If the vibration is too great, the crankshaft will be damaged. The vibration damper limits the torsional vibrations to an acceptable amount in order to prevent damage to the crankshaft.Rubber Vibration Damper (If Equipped)
Illustration 7 g00818663
Rubber Vibration Damper
(1) Crankshaft
(2) Ring
(3) Rubber ring
(4) Hub
(5) Alignment marks The rubber vibration damper is installed on the front of crankshaft (1). The hub (4) and ring (2) are isolated by a rubber ring (3). The rubber vibration damper has alignment marks (5) on the hub and the ring. These marks give an indication of the condition of the rubber vibration damper.Viscous Vibration Damper (If Equipped)
Illustration 8 g00816013
Cross Section Of Viscous Vibration Damper
(1) Crankshaft
(2) Weight
(3) Case The viscous vibration damper is installed on the front of crankshaft


Parts piston Force:

F428015-1
 
F428015-1 PISTON
H0503B83A, H0503H84B, H0507B85A, H0507C86A, H0507C87A, H0507H81A, H0507H82B, H0555H74G
FA435260
 
FA435260 PISTON RING SET (4 PER SET)
H0503H84B, H0507B85A, H0507C86A, H0507C87A, H0507H81A, H0507H82B, H0555H74G
818115A 1
 
818115A 1 PISTON RINGS (4 PER SET) .030 OVERSIZE (NOT SHOWN)
H0503H84B, H0507B85A, H0507C86A, H0507C87A, H0507H81A, H0507H82B, H0555H74G
F377015-1
 
F377015-1 PISTON 35 H.P.
H0352H77H, H0352H79L, H0353H78K, H0353H80M, H0353H81N, H0353H82P
FA353260
 
FA353260 PISTON RING SET (6 PER SET) 35 H.P.
H0352H77H, H0352H79L, H0353H78K, H0353H80M, H0353H81N, H0353H82P
FS307260
 
FS307260 PISTON RINGS (6 PER SET) .010 OVERSIZE (NOT SHOWN) 35 H.P.
H0352H77H, H0352H79L, H0353H78K, H0353H80M, H0353H81N, H0353H82P
818112A 1
 
818112A 1 PISTON RINGS (6 PER SET) .030 OVERSIZE (NOT SHOWN) 35 H.P.
H0352H77H, H0352H79L, H0353H78K, H0353H80M, H0353H81N, H0353H82P
Back to top