F7017 Force PISTON PIN


F7017 PISTON PIN Force H0033H75C, H0060B76A, H0062H79M, H0064H78D, H0082H76G PISTON
F7017 PISTON PIN Force
Rating:
103

Buy PISTON PIN F7017 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 2
 

Force entire parts catalog list:

H0033H75C 1975,1977
H0060B76A 1976
H0062H79M 1979
H0064H78D 1978
H0082H76G 1976,1977

Information:


Illustration 1 g00759504
SchematicTest Step 1. Inspect Electrical Connectors and Wiring
Turn the keyswitch to the OFF/RESET position.
Thoroughly inspect ECM connector J1/P1, machine connector J3/P3, and throttle switch connector J118/P118. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Check the harness and wiring for corrosion, abrasion, and pinch points from the throttle switch to the ECM.Expected Result:All connectors, pins, and sockets should be completely inserted and coupled. The harness and wiring should be free of corrosion, abrasion, and pinch points.Results:
OK - Proceed to Test Step 2.
Not OK - Repair: Repair the circuit.Verify that the repair eliminates the problem.STOPTest Step 2. Check "Throttle Cab Switch Position" on ET
Connect ET at the service tool connector.
Turn the keyswitch to the ON position.
Observe the status of the throttle switch and the throttle inputs on ET while you operate the throttle switch in each position.Results:
OK - The throttle switch is functioning properly at this time.Repair: Refer to Troubleshooting, "Electrical Connectors - Inspect" if the problem is intermittent.STOP
Not OK - Record the suspect input. Proceed to Test Step 3.Test Step 3. Jumper the Switch Input at the Throttle Switch Connector
Disconnect throttle switch connector J118/P118.
Observe the status of the suspect throttle input on ET.
Use a suitable piece of wire to short P118:1 (Digital Return) to the terminal for the suspect throttle input at throttle switch connector P118.
Observe the status of the suspect throttle input on ET.
Remove the wire short.Expected Result:The status of the suspect throttle input should be "Off" when throttle switch connector J118/P118 is disconnected. The status should be "On" when the wire short is installed.Results:
OK - The harness and the ECM are OK.Repair: Replace the throttle switch.Verify that the repair eliminates the problem.STOP
Not OK - Proceed to Test Step 4.Test Step 4. Check for Shorts in the Harness
Turn the keyswitch to the OFF/RESET position.
Disconnect ECM connector J1/P1 and throttle switch connector J118/P118.
Measure the resistance between engine ground and the terminal for the suspect throttle input at throttle switch connector P118.
Measure the resistance between the terminal for the suspect throttle input at throttle switch connector P118 and the remaining terminals at the connector.Expected Result:Resistance should be greater than 20,000 for each reading.Results:
OK - Proceed to Test Step 5.
Not OK - There is a short in the harness between the ECM and the throttle switch.Repair: Repair the circuit.Verify that the repair eliminates the problem.STOPTest Step 5. Check Resistance through the Harness
Illustration 2 g00759522
ECM connector P1 (ECM side)
Use a suitable piece of wire to short P118:1 (Digital Return) to the terminal of the suspect throttle input at throttle switch connector P118.
Measure the resistance between P1:29 (Digital Return) and the terminal for the suspect throttle input at ECM connector P1.Expected Result:Resistance should be less than 10 Ohms.Results:
OK - Proceed to Test Step 6.
Not OK - There is an open circuit or excessive resistance in the harness.Repair: Repair the circuit.Verify that the repair eliminates the problem.STOPTest Step 6. Check the Harness and the ECM
Illustration 3 g00759535
ECM connector P1 (wire side)
Turn the keyswitch to the OFF/RESET position.
Disconnect ECM connector J1/P1 and remove the wire for the suspect throttle input from ECM connector P1.
Reconnect all connectors.
Turn the keyswitch to the ON position.
Observe the status of the suspect throttle input on ET.
Turn the keyswitch to the OFF/RESET position.
Disconnect ECM connector J1/P1 and remove the wire from P1:5 (Digital Return).
Fabricate a jumper wire with pins at both ends. Insert the jumper wire at P1:5 (Digital Return) and the suspect throttle input at ECM connector P1.
Reconnect all connectors.
Turn the keyswitch to the ON position.Note: Additional diagnostic codes will be generated because P1:5 (Digital Return) will no longer be connected to other sensors and switches. Ignore the codes and clear the codes when you complete this test.
Observe the status of the suspect throttle input on ET.
Turn the keyswitch to the OFF/RESET position.
Remove the jumper wire from ECM connector P1 and reconnect all wires and connectors.Expected Result:The status of the suspect throttle input should be "Off" when the throttle input is open. The status should be "On" when the jumper wire (short) is installed.Results:
OK - There is a problem in the harness between the ECM and the throttle switch.Repair: Repair the circuit.Verify that the repair eliminates the problem.STOP
Not OK - The switch signal appears at the ECM. The ECM is not reading the switch properly.Repair: Verify your results. Replace the ECM. Refer to Troubleshooting, "Replacing the ECM" before replacing the ECM.STOP


Parts piston Force:

F127015
 
F127015 PISTON
H0033H75C
FA429015
 
FA429015 PISTON
H0060B76A, H0062H79M, H0064H78D, H0082H76G
FA317260
 
FA317260 PISTON RING SET (3 PER SET)
H0060B76A, H0062H79M, H0064H78D, H0082H76G
F430017
 
F430017 PISTON PIN
H0082H76G, H0082H79K
FA430015
 
FA430015 PISTON
H0082H76G, H0082H79K
818038A 1
 
818038A 1 PISTON RING SET (2 PER SET)
H0032H84G, H0042081C, H0042082D, H0042083E, H0042B78C, H0042B80G, H0042C84L, H0042H77B, H0042H78D, H0042H78E, H0042H79F, H0043F85A, H0052C88A, H0060B78B, H0060H79C, H0060H80D, H0062B78J, H0062H79K, H0064H80F, H0064H82H, H0067H79C, H0070B79A, H0071H81
Back to top