FS310260 Force PISTON RINGS (6 PER SET) .010 OVERSIZE (NOT SHOWN)


FS310260 PISTON RINGS (6 PER SET) .010 OVERSIZE (NOT SHOWN) Force H0352H77H, H0356H75F, H0456B78J, H0456B79K, H0456B80L, H0457H82N, H0457H83P PISTON
FS310260 PISTON RINGS (6 PER SET) .010 OVERSIZE (NOT SHOWN) Force
Rating:
68

Buy PISTON RINGS (6 PER SET) .010 OVERSIZE (NOT SHOWN) FS310260 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: &nbsp
 

Force entire parts catalog list:

H0352H77H 1977,1978
H0356H75F 1975,1976,1977
H0456B78J 1978
H0456B79K 1979
H0456B80L 1980,1981
H0457H82N 1982
H0457H83P 1983,1984

Information:

Drain
Pressurized System: Hot coolant can cause serious burns. To open the cooling system filler cap, stop the engine and wait until the cooling system components are cool. Loosen the cooling system pressure cap slowly in order to relieve the pressure.
Stop the engine and allow the engine to cool. Loosen the cooling system filler cap slowly in order to relieve any pressure. Remove the cooling system filler cap.
Open the cooling system drain valve (if equipped). If the cooling system is not equipped with a drain valve, remove the cooling system drain plugs.Allow the coolant to drain.
Dispose of used engine coolant properly or recycle. Various methods have been proposed to reclaim used coolant for reuse in engine cooling systems. The full distillation procedure is the only method acceptable by Caterpillar to reclaim the used coolant.
For information regarding the disposal and the recycling of used coolant, consult your Caterpillar dealer or consult Dealer Service Tools.Flush
Flush the cooling system with clean water in order to remove any debris.
Close the drain valve (if equipped). Clean the drain plugs. Install the drain plugs. Refer to Torque Specifications, SENR3130 for more information on the correct torques.
Do not fill the cooling system faster than 5 L (1.3 US gal) per minute to avoid air locks.Cooling system air locks may result in engine damage.
Fill the cooling system with clean water. Install the cooling system filler cap.
Start and run the engine at low idle until the temperature reaches 49 to 66 °C (120 to 150 °F).
Stop the engine and allow the engine to cool. Loosen the cooling system filler cap slowly in order to relieve any pressure. Remove the cooling system filler cap. Open the drain valve (if equipped) or remove the cooling system drain plugs. Allow the water to drain. Flush the cooling system with clean water. Close the drain valve (if equipped). Clean the drain plugs. Install the drain plugs. Refer to Torque Specifications, SENR3130 for more information on the correct torques.Fill
Do not fill the cooling system faster than 5 L (1.3 US gal) per minute to avoid air locks.Cooling system air locks may result in engine damage.
Fill the cooling system with Extended Life Coolant (ELC). Refer to this Operation and Maintenance Manual, "Refill Capacities and Recommendations" topic (Maintenance Section) for more information on cooling system specifications. Do not install the cooling system filler cap.
Start and run the engine at low idle. Increase the engine rpm to high idle. Run the engine at high idle for one minute in order to purge the air from the cavities of the engine block. Stop the engine.
Check the coolant level. Maintain the coolant level within 13 mm (0.5 inch) below the bottom of the pipe for filling. Maintain the coolant level within 13 mm (0.5 inch) to the proper level on the sight glass (if equipped).
Clean the cooling system filler cap. Inspect the gasket that is on the cooling system filler cap. If the gasket that is on the cooling system filler cap is damaged, discard the old cooling system filler cap and install a new cooling system filler cap. If the gasket that is on the cooling system filler cap is not damaged, use a 9S-8140 Pressurizing Pump in order to pressure test the cooling system filler cap. The correct pressure for the cooling system filler cap is stamped on the face of the cooling system filler cap. If the cooling system filler cap does not retain the correct pressure, install a new cooling system filler cap.
Start the engine. Inspect the cooling system for leaks and for proper operating temperature.


Parts piston Force:

F40017-2
 
F40017-2 PISTON PIN
H0257F88A, H0257F88B, H0306B80C, H0307H81D, H0350H78L, H0351H76K, H0352F90B, H0352F90C, H0352H77H, H0352H79L, H0353E91A, H0353E91B, H0353H78K, H0353H80M, H0353H81N, H0353H82P, H0355D89A, H0356F89B, H0356H75F, H0357C86A, H0357C87A, H0357C88B, H0357F88
FT2990
 
FT2990 PISTON PIN REMOVER
H0032H84G, H0042081C, H0042082D, H0042083E, H0042C84L, H0043F85A, H0202B80L, H0202B81M, H0202H79K, H0202H82N, H0252B83G, H0252H77B, H0252H78C, H0252H78D, H0254H75A, H0257F88A, H0257F88B, H0306B80C, H0307H81D, H0350H78L, H0351H76K, H0352F90B, H0352F90
F486015
 
F486015 PISTON
H0352H77H, H0356H75F, H0456B78J, H0456B79K, H0456B80L, H0457H82N, H0457H83P
FA354260
 
FA354260 PISTON RING SET (6 PER SET)
H0352H77H, H0356H75F, H0456B78J, H0456B79K, H0456B80L, H0457H82N, H0457H83P
818113A 1
 
818113A 1 PISTON RINGS (6 PER SET) .030 OVERSIZE (NOT SHOWN)
H0352H77H, H0356H75F, H0456B78J, H0456B79K, H0456B80L, H0457H82N, H0457H83P
FSA486015
 
FSA486015 PISTON .010 OVERSIZE (NOT SHOWN)
H0352H77H, H0356H75F, H0456B78J, H0456B79K, H0456B80L, H0457H82N, H0457H83P
818124A 1
 
818124A 1 PISTON .030 OVERSIZE (NOT SHOWN)
H0352H77H, H0356H75F, H0456B78J, H0456B79K, H0456B80L, H0457H82N, H0457H83P
F377015-1
 
F377015-1 PISTON 35 H.P.
H0352H77H, H0352H79L, H0353H78K, H0353H80M, H0353H81N, H0353H82P
Back to top