FSA458260 Force PISTON RINGS (4 PER SET) .010 OVERSIZE (NOT SHOWN)


FSA458260 PISTON RINGS (4 PER SET) .010 OVERSIZE (NOT SHOWN) Force H0202B80L, H0202B81M, H0202H79K, H0202H82N, H0252B83G, H0252H77B, H0252H78C, H0252H78D, H0254H75A PISTON
FSA458260 PISTON RINGS (4 PER SET) .010 OVERSIZE (NOT SHOWN) Force
Rating:
43

Buy PISTON RINGS (4 PER SET) .010 OVERSIZE (NOT SHOWN) FSA458260 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: -
 

Force entire parts catalog list:

H0202B80L 1980
H0202B81M 1981
H0202H79K 1979
H0202H82N 1982
H0252B83G 1983,1984
H0252H77B 1977
H0252H78C 1978
H0252H78D 1978
H0254H75A 1975,1976

Information:


Table 1
Specifications for 346-4197 Crankshaft Gp    
Callout     Part Number     Part Name     Specification Description    
-     338-1402     Crankshaft Gear     Maximum permissible temperature of the gear for installation on the crankshaft is 180 °C (356 °F).    
-     355-8526     Crankshaft     The end play of a new crankshaft is
0.1 to 0.41 mm (0.00394 to 0.01614 inch).    
7     363-0559     Thrust Washer     Standard thickness of thrust washer is
2.69 to 2.75 mm (0.10591 to 0.10827 inch).    
-     -     Journal 1     Mounting    
-     -     Journal 2     Run out of the journal is
0.08 mm (0.0031 inch).    
-     -     Journal 3     Run out of the journal is
0.15 mm (0.0059 inch).    
-     -     Journal 4     Run out of the journal is
0.08 mm (0.0031 inch).    
-     -     Journal 5     Mounting    Inspect the crankshaft for wear or for damage. For more information regarding the servicing of the crankshaft, contact the Dealer Solution Network (DSN).Removal Procedure
Table 2
Required Tools    
Tool     Part Number     Part Description     Qty    
A     1U-8221     Lifting Sling     2    
B     -     5mm Allen Socket     1    Start By:
Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump" for the correct procedure.
Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front)" for the correct procedure.
Remove the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal" for the correct procedure.
Remove the rocker shaft and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod" for the correct procedure.
If necessary, remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head" for the correct procedure.
If necessary, remove the pistons and connecting rods. Refer to Disassembly and Assembly, "Pistons and Connecting Rods" for the correct procedure.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
The engine should be mounted on a suitable stand and placed in the inverted position.
If the cylinder head, the pistons and the connecting rods have not been removed already, remove the connecting rod bearings. Refer to Disassembly and Assembly, "Connecting Rod Bearings" for the correct procedure.
Illustration 1 g02441836
Use Tooling (B) in order to remove allen head screws (1) . Remove bridge piece (2) .
Ensure that the main bearing caps are marked for the location and orientation.
Illustration 2 g02441837
Illustration 3 g02441838
Remove bolts (3) from main bearing caps (2) . Remove main bearing caps (2) from the cylinder block.
Take care not to displace dowels (6) .
Remove lower main bearing shells (5) from main bearing caps (4) . Keep the lower main bearing shells with the respective main bearing caps.Note: The lower main bearing shells are plain bearings that have no oil holes.
Illustration 4 g02441839
Attach Tooling (A) and a suitable lifting device to crankshaft (7) . Lift crankshaft (7) out of the cylinder block. The weight of the crankshaft is approximately 39 kg (86 lb).Note: Do not damage any of the finished surfaces on the crankshaft. When the crankshaft is removed from the engine, the crankshaft must be supported on a suitable stand in order to prevent damage to the crankshaft timing ring.
Illustration 5 g02441840
Remove upper main bearing shells (8) from the cylinder block. Keep the upper main bearing shells with the respective main bearing caps.Note: The upper main bearing shells have a groove and two oil holes.
Remove thrust washers (7) .
If necessary, remove the crankshaft timing ring. Refer to Disassem


Parts piston Force:

FT2990
 
FT2990 PISTON PIN REMOVER
H0032H84G, H0042081C, H0042082D, H0042083E, H0042C84L, H0043F85A, H0202B80L, H0202B81M, H0202H79K, H0202H82N, H0252B83G, H0252H77B, H0252H78C, H0252H78D, H0254H75A, H0257F88A, H0257F88B, H0306B80C, H0307H81D, H0350H78L, H0351H76K, H0352F90B, H0352F90
F458017
 
F458017 PISTON PIN
H0202B80L, H0202B81M, H0202H79K, H0202H82N, H0252B83G, H0252H77B, H0252H78C, H0252H78D, H0254H75A
F458015-1
 
F458015-1 PISTON
H0202B80L, H0202B81M, H0202H79K, H0202H82N, H0252B83G, H0252H77B, H0252H78C, H0252H78D, H0254H75A
FA458260
 
FA458260 PISTON RING SET (4 PER SET)
H0202B80L, H0202B81M, H0202H79K, H0202H82N, H0252B83G, H0252H77B, H0252H78C, H0252H78D, H0254H75A
818119A 1
 
818119A 1 PISTON RINGS (4 PER SET) .030 OVERSIZE (NOT SHOWN)
H0202B80L, H0202B81M, H0202H79K, H0202H82N, H0252B83G, H0252H77B, H0252H78C, H0252H78D, H0254H75A
FSA458015
 
FSA458015 PISTON .010 OVERSIZE (NOT SHOWN)
H0202B80L, H0202B81M, H0202H79K, H0202H82N, H0252B83G, H0252H77B, H0252H78C, H0252H78D, H0254H75A
818118A 1
 
818118A 1 PISTON .030 OVERSIZE (NOT SHOWN)
H0202B80L, H0202B81M, H0202H79K, H0202H82N, H0252B83G, H0252H77B, H0252H78C, H0252H78D, H0254H75A
Back to top