F8028 Force PLAIN WASHER

Table 1
Required Tools
Tool Part Number Part Description Qty
A 9S-9082 Engine Turning Tool 1
B 8S-1378 Stud Remover and Resetter Tool 1
C 1B-9575 Bolt 2
C 9M-1974 Hard Washer 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Engines Without a Camshaft Rear Gear
Illustration 1 g00834103
Install the key (1) in the camshaft (2). Be sure that the key (1) is seated in the camshaft (2).
Illustration 2 g00834106
(2) Camshaft
(3) Dowel
(X) 8.5 0.5 mm (0.33 0.02 inch)
Install dowel (3) in the rear of camshaft (2). Install dowel (3) to a dimension of 8.5 0.5 mm (0.33 0.02 inch).
Illustration 3 g00834109
Install camshaft drive gear (4) on camshaft (2) if camshaft drive gear (4) has been removed. There are two methods that can be used in order to install camshaft drive gear (4) on the camshaft. Preferred Method - Mechanically press camshaft drive gear (4) on camshaft (2) without heating camshaft drive gear (4).Alternative Method - Heat camshaft drive gear (4) to a maximum temperature of 205 °C (400 °F) for no more than one hour and manually install camshaft drive gear (4) on camshaft (2). Do not use a torch to heat camshaft drive gear (4).
Put 8T-2998 Lubricant on the camshaft lobes and the rollers of the lifters. Put clean engine oil on the bearing journals of the camshaft.
Illustration 4 g00834110
Carefully install camshaft (2) in the cylinder block. Do not force the camshaft into position. If resistance to camshaft installation occurs, turn the camshaft so the lobes will align the bearing journals with the camshaft bearing bores.
Illustration 5 g00834113
Align the "V" marks on the camshaft drive gear and the idler gear in the front of the engine.
Illustration 6 g00834115
Install plate (5) on the cylinder block. Engines With a Camshaft Rear Gear
Note: All 3408E Engines have a balancer gear that is located in the flywheel housing. The balancer gear is driven by the crankshaft or the camshaft. The balancer gear has a timing mark. This timing mark must be aligned with the timing mark of the gear that drives the balancer gear. If there is access to the rear camshaft gear through the flywheel housing, the rear camshaft gear may be removed without removing the flywheel housing. If the balancer gear is driven by the crankshaft, the camshaft rear gear can be removed and installed without regarding the timing. If the balancer gear is driven by the camshaft rear gear, the timing marks on the camshaft rear gear and the balancer gear must be aligned when the camshaft rear gear is installed. Refer to Disassembly and Assembly, "Balancer Group - Remove" and Disassembly and Assembly, "Balancer Group - Install". 3412 Engines do not have a balancer gear. A dowel in the rear of the camshaft positions the rear camshaft gear on the camshaft. The rear camshaft gear is secured to the camshaft with four bolts.
Illustration 7 g00834103
Install the key in the camshaft. Be sure that the key is seated in the camshaft.
Illustration 8 g00834106
(2) Camshaft
(3) Dowel
(X) 8.5 0.5 mm (0.33 0.02 inch)
Install dowel (3) in the rear of camshaft (2). Install the dowel to a dimension of 8.51 mm (0.335 inch) to 9.01 mm (0.355 inch).