819152 Force PLATE-EXHAUST


819152 PLATE-EXHAUST Force H025201RD, H025201TD, H025201TS, H025201US PLATE

Buy PLATE-EXHAUST 819152 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 16
 

Compatible models:

Force entire parts catalog list:

H025201RD 1995,1996
H025201TD 1997
H025201TS 1997
H025201US 1998

Information:

1. Use tool (A), and remove three filter assemblies (4) from the oil filter base.2. Remove the bolts that hold elbows (2) and (3) to the oil filter base. Move the elbows away from the oil filter base.3. Fasten a hoist and tool (B) to oil filter base (1). Remove the bolts that hold oil filter base (1) to the engine. Remove the oil filter base from the engine. The weight of the oil filter base is 32 kg (70 lb). The following steps are for installation of the oil filter base.4. Fasten a hoist and tool (B) to oil filter base (1). Put the oil filter base in position on the engine, and install the bolts that hold it.5. Put new gaskets and elbows (2) and (3) in position on the end of the oil filter base. Install the bolts that hold them in place.6. Put clean oil on the seals of filter assemblies (4), and install the filter assemblies. Follow the instructions on the filter assemblies.7. Fill the engine with oil to the correct level. See the Operation & Maintenance manual for further information.Disassemble & Assemble Oil Filter Base (3512 EUI)
Start By:a. remove oil filter base
Typical Example1. Remove the bolts and support (2) from oil filter base assemblies (1).
Typical Example2. Remove cover (6), spring (5) and plunger (4) from each of the base assemblies.3. Remove elbow (3) from base assemblies (1).4. Remove the bolts that hold base assemblies (1) together, and separate the base assemblies.5. If necessary, remove the stud from each of the base assemblies. The following steps are for assembly of the oil filter base.6. If the studs were removed from base assemblies (8), put 9S3263 Thread Lock on the tapered end of the studs for a distance of 10.2 mm (0.402 in). Install the studs in the base assemblies, and tighten them to a torque of 80 14 N m (60 10 lb ft).7. Put the gaskets in position between base assemblies (1). Install the bolts that hold them together.8. Put the gasket and elbow (3) in position on the base assemblies, and install the bolts that hold them.9. Install plunger (4) and spring (5) in each of the base assemblies.10. Put the gaskets and covers (6) in position, and install the bolts that hold them.11. Put support (2) in position on base assemblies (1), and install the bolts that hold it in place.End By:a. install oil filter baseRemove & Install Oil Filter Base (3516 EUI)
1. Remove the bolts holding the wire harness clips and move the wiring harness out of the way. 2. Use tool (A), and remove four filter assemblies (4) from the oil filter base.3. Remove the bolts that hold elbow (2) and adapter (3) to the oil filter base. Move the elbow and adapter away from the oil filter base.4. Fasten a hoist and tool (B) to oil filter base (1). Remove the bolts that hold oil filter base (1) to the engine. Remove the oil filter base from the engine. The weight of the oil filter base is 39 kg (86 lb). The following steps are for installation of the oil filter base.5. Fasten a hoist and tool (B) to oil filter base (1). Put the oil filter base in position on the engine, and install the bolts that hold it.6. Put new gaskets and elbows (2) and (3) in position on the end of the oil filter base. Install the bolts that hold them in place.7. Put clean oil on the seals of filter assemblies (4), and install the filter assemblies. Follow the instructions on the filter assemblies.8. Put the wiring harness and clips in place and install the bolts in the clips.9. Fill the engine with oil to the correct level. See the Operation & Maintenance manual for further information.Disassemble & Assemble Oil Filter Base (3516 EUI)
Start By:a. remove oil filter base 1. Remove elbow (1), support (2) and adapter (3) from the oil filter base assemblies.2. Remove cover (4), gasket (5), spring (6) and plunger (7) from each of the base assemblies.3. Remove the bolts that hold base assemblies (8) together.4. If necessary, remove the stud from each of the base assemblies. The following steps are for assembly of the oil filter base.5. If the studs were removed from base assemblies (8), put 9S3263 Thread Lock on the tapered end of the studs for a distance of 10.2 mm (0.402 in). Install the studs in the base assemblies, and tighten them to a torque of 80 14 N m (60 10 lb ft).6. Put the gaskets in position between base assemblies (8). Install the bolts that hold them together.7. Put gaskets and elbow (1) and adapter (3) in position on the base assemblies, and install the bolts that hold them.8. Install plunger (7) and spring (6) in each of the base assemblies.9. Put gaskets (5) and covers (4) in position, and install the bolts that hold them.10. Put support (2) in position on base assemblies (8), and install the bolts that hold it in place.End By:a. install oil filter base


Parts plate Force:

819281
 
819281 PLATE (91C/92B & SER. # E000001 THRU E090399)
H0091H84D, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H0152C84K, H0152S89A, H025201RD, H025201TD, H025201TS
819155T
 
819155T PLATE-STATOR
H025201RD, H025201TD, H025201TS, H025201US
819153T
 
819153T PLATE-REED
H025201RD, H025201TD, H025201TS, H025201US
830282 1
 
830282 1 PLATE-HANDLE SUPPORT
H025201RD, H025201TD, H025201TS, H025201US
29310
 
29310 PLATE
H009201UD, H009201US, H015201US, H025201RD, H025201TD, H025201TS, H040312RD, H040312SD, H040312UD
819281 4
Back to top