820629 Force PLATE ASSEMBLY (WITH CORE), STATOR


820629 PLATE ASSEMBLY (WITH CORE), STATOR Force H0052C88A PLATE
820629 PLATE ASSEMBLY (WITH CORE), STATOR Force
Rating:
28

Buy PLATE ASSEMBLY (WITH CORE), STATOR 820629 Force genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$74.91
 

30-09-2017
.11[0.00] pounds
Briggs &am: Briggs & Stratto
Briggs & Stratton # 820629 SHIELD-HEAT
Sold on Amazon
Number on catalog scheme: 8
 

Compatible models:

H0052C88A   Force

Force entire parts catalog list:

H0052C88A 1988,1989,1990,1991,1992,1993,1994,1995

Information:


Table 1
Diagnostic Codes Table    
Code and Description    Conditions which Generate this Code    System Response    
E265(3) User Defined Shutdown     The inputs from the ground level shutdown switch to the Electronic Control Module (ECM) have changed states.     The engine will shut down. The code is logged.    
267-3 Remote Shutdown Input : Voltage Above Normal     Both of the switch contacts of the ground level shutdown switch are in the open state.     If both of the switch contacts from the ground level shutdown switch change to the same state and the engine is running, the engine will continue to run. The code is logged.    
267-4 Remote Shutdown Input : Voltage Below Normal     Both of the switch contacts of the ground level shutdown switch are in the closed state.    The ground level shutdown switch provides the ability to shut down the engine. The engine's ECM remains active. Caterpillar Electronic Technician (ET) can be used to communicate with the ECM. The ground level shutdown switch must be returned to the RUN position and the engine rpm must be zero before the ECM will allow the engine to start.To shut down the engine, lift the red cover guard and toggle the ground level shutdown switch to the SHUTDOWN position. The ECM reads the position of the ground level shutdown switch. If the engine is running, the ECM disables the fuel injection. The status screen will display "INJECTION DISABLED" and "REMOTE SHUTDOWN".The ECM will not allow the engine to start if the status for the ground level shutdown switch is "REMOTE SHUTDOWN".
Illustration 1 g01303340
Schematic
Illustration 2 g01303342
P1 ECM connector (P1-54) user defined shutdown (NO) (P1-56) user defined shutdown (NC)Test Step 1. Inspect Electrical Connectors and Wiring
Turn the keyswitch to the OFF position.
Thoroughly inspect the ECM connector J1/P1. Thoroughly inspect the connectors for the ground level shutdown switch. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector that are associated with the circuit.
Check the ECM connector (allen head screw) for the proper torque. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Check the harness and the wiring for abrasion and for pinch points.Expected Result:All connectors, pins, and sockets are completely coupled and/or inserted. The harness and wiring are free of corrosion, of abrasion, and of pinch points.Results:
OK - The harness and wiring are OK. Proceed to Test Step 2.
Not OK - There is a problem in the connectors and/or wiring.Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled.Verify that the repair eliminates the problem.STOPTest Step 2. Check the Status of the Ground Level Shutdown Switch on Cat ET
Connect Cat ET to the service tool connector. Start Cat ET.
Turn the keyswitch to the ON position.
Observe the status of the ground level


Parts plate Force:

F521537
 
F521537 PLATE, WATER PUMP
H0032H84G, H0042081C, H0042082D, H0042083E, H0042B78C, H0042B80G, H0042C84L, H0042C87A, H0042H77B, H0042H78D, H0042H78E, H0042H79F, H0043F85A, H005201RS, H005201SD, H005201TS, H005201UD, H0052C88A
FA341151
 
FA341151 PLATE, EXHAUST
H0032H84G, H0042081C, H0042082D, H0042083E, H0042B78C, H0042B80G, H0042C84L, H0042C87A, H0042H78D, H0042H78E, H0042H79F, H0043F85A, H005201RS, H005201SD, H005201TS, H005201UD, H0052C88A
F2A24757
 
F2A24757 PLATE FUEL PUMP REED W/REEDS AND SCREWS
H005201RS, H005201SD, H005201TS, H005201UD, H0052C88A, H0060H79C, H0060H80D, H0064H80F, H0064H82H, H0067H79C, H0071H81B, H0071H82C, H0071H83D, H0071H84E, H0072B81D, H0072H82E, H0091B80B, H0091H79A, H0091H83C, H0091H84D, H009201RS, H009201SD, H009201U
F687038T
 
F687038T PLATE, SUPPORT (PAINTED)
H005201RS, H005201SD, H005201TS, H0052C88A
F702038
819677
 
819677 PLATE, REED
H005201RS, H005201SD, H005201TS, H005201UD, H0052C88A
819345A 2
 
819345A 2 PLATE ASSEMBLY, STATOR
H005201RS, H005201SD, H005201TS, H005201UD, H0052C88A
Back to top